Summary of the content on the page No. 1
MODELS
SF6000
SF5510
SF4030
SF4010
SF3010
SF3000
HD 4010
Summary of the content on the page No. 2
5 YEAR LIMITED WARRANTY 5 This Dukane audio visual product is warranted to the original purchaser under a 5 year limited warranty – – in normal use and service – – against defects in material and workmanship. DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,INCLUDING ALL WARRANTIES OF MERCHANT- ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. During the warranty period, Dukane Corporation will repair or replace (at the Manufacturer’s option) any such defective part
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS When using your overhead projector, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Close supervision is necessary when any projector is used by or near children. Do not leave projector unattended while in use. 3. Care must be taken as burns can occur from touching hot parts. 4. Do not operate projector with a damaged cord or if the projector has been dropped or damaged — until it
Summary of the content on the page No. 4
Thank you for choosing a Starfire® Series Portable/Professional Overhead Projector. The sleek, low-profile Starfire Overhead Projectors are available in your choice of 3000, 4000/3200, 5500/4400 and 6000 ANSI lumens. Features of each model vary and can include a single, triple or triple/wide-angle lens; built-in AC outlets; and even an electronic “soft start” power supply that improves the projected image, extends the lamp life and reduces operating costs. Because operation of all units is very
Summary of the content on the page No. 5
TABLE OF CONTENTS Page LIFETIME LIMITED WARRANTY .................................Inside Cover SPECIFICATIONS .................................................................. 1 ELECTRICAL SAFETY GROUNDING INSTRUCTIONS ........................ 1 INDEX OF FUNCTIONAL PARTS ............................................. 2-3 SF MODEL SETUP and FOLDUP ............................................. 4-5 HD MODEL SETUP ................................................................. 6 OPERATION ........
Summary of the content on the page No. 6
Summary of the content on the page No. 7
SPECIFICATIONS SF MODEL Dimensions........... 5.6" H x 16.4" W x 17.8" D (Folded) 32" H x 16.4" W x 17.8" D (Opened) HD MODEL Dimensions.......... 8.5" H x 16.4" W x 17.8" D (Folded) 32" H x 16.4" W x 17.8" D (Opened) Aperture............................... 6000, 5510 — 11.2" x 11.2" (A4) 3000, 3010, 4010, 4030 — 10.5" x 10.5" Lens ............................ 3000 — Single Element, 293mm (11.5") 3010, 4010, 5510 — Three Element, 327mm (13.0") 4030, 6000 — Four Element, 280mm (11.0") Lamp ......
Summary of the content on the page No. 8
INDEX OF FUNCTIONAL PARTS A number of terms are used frequently in this instruction booklet. The OVERHEAD PROJECTOR will be easier to operate if you become familiar with the terms for the functional parts listed below: 1 2 2a 4 5 6 7 8 10 3 11 9 1. Mirror; use to direct projected 4. Mast; rack & pinion focusing image mechanism 2. Projection Head; rotates 180° 5. Focus Knob; turn to focus pro- to allow projection in different jected image directions or onto different 6. Stage; place presentation
Summary of the content on the page No. 9
13 12 14 15 12. Door Leg Assembly; close for 14. Lamp Change Lever; slide for foldaway design, cord storage replacement/reserve lamp 13.Door Latch (one each side); 15. Power Cord; stored in the unit’s keeps doors closed base Models 6000 and 4030 also feature a soft start power supply which extends lamp life, reduces operating costs and ensures a smoother, flicker-free image. 3
Summary of the content on the page No. 10
SETUP INSTRUCTIONS SF MODELS 1. Set unit on projection table in the vertical position (handle up). 2. Slide bottom door latches out and swing both doors around to magnet latches. Pull out the entire power cord. Leave doors open. 3. Tip unit over to rest on its legs. (Doors act as feet for the unit). 4. Turn focus knob clockwise until it stops at the end of the mast. 5. Rotate mast up until it locks into place. 6. Rotate the projection head assembly counterclockwise to the working position. Doors
Summary of the content on the page No. 11
STEP 6 — STEP 7 — FOLDUP INSTRUCTIONS Perform Setup Steps in reverse order. • Unlock/lower mast by pushing down on lock collar as shown. 5
Summary of the content on the page No. 12
SETUP INSTRUCTIONS HD MODELS 1. Set unit on projection table and pull out the power cord from cord storage compartment. 2. Turn focus knob clockwise until it stops at the end of the mast. 3. Rotate mast up until it locks into place. 4. Rotate the projection head assembly counterclockwise to the working position. 5. Open mirror. STEP 2 — STEP 1 — STEP 3 — STEP 4 — STEP 5 — 6
Summary of the content on the page No. 13
OPERATION Place the projector on a stable surface that is desk or table height. Make sure that the side vent is not blocked. Plug the power cord into a standard 120V AC outlet. Push the power button to turn the projector on. I=ON O = OFF Place a transparency on the stage. Adjust the focus by turning the focus knob. You may alternate between the wide angle (SF6000 & 4030) and standard lens by rotating the 4th element lens towards or away from the projection head (some adjustment on screen-to- pro
Summary of the content on the page No. 14
High/Low Lamp Switch When using with an LCD panel, use the projector at its brightest lumen output (Models 6000, 5510, 4030, 4010). Reduce light output (High/Low switch) to extend lamp life. Ideal when using regular transparencies. Lamp Changer The lamp changer allows you to quickly replace a failed lamp. Turn the power switch “OFF.” Simply push slightly, then slide the lamp changing lever towards the side labeled “RESERVE.” LEVER CAUTION: If the OHP is brought directly from a cold to a warm lo
Summary of the content on the page No. 15
LAMP REPLACEMENT Your projector uses: 3000, 3010 — 360W, ENX. 4010, 4030, 5510, 6000 — 410W, FXL. WARNING Lamp and adjacent metal parts are hot. Allow lamp to cool before replacing. Glass components may shatter. Handle carefully. To Remove an Exhausted Lamp: 1. Remove the lamp by squeezing the lamp retainer clip and remove lamp. 2. Avoid touching the new lamp — oily skin can cause discoloration of the lamp capsule or reflector. 3. Push the new lamp down into socket until firmly seated and the re
Summary of the content on the page No. 16
CLEANING For best performance, keep your projector free of dust and surface dirt. Keep covered when not in use. Daily Cleaning: Use a soft, lint-free cloth to remove dust from stage glass, projection lens and magnifier lens (6000 and 4030 models only). Lens cleaner may also be used on these components. Projection Mirror: Do not attempt to clean this mirror with cleaning agents — use a soft lens brush to remove dirt. Fresnel Lens: Use a soft, lint-free cloth or soft brush to remove dust. Use of c
Summary of the content on the page No. 17
TROUBLESHOOTING Symptom Probable Cause Solution Neither lamp or a. Unit unplugged a. Plug unit into fan operate outlet b. No power at wall outlet b. Verify outlet has power c. Stage lid not closed c. Close stage lid d. Mirror box not lowered, d. Open bottom (interlock switch not doors and insure activated) mirror box lowers e. Blown fuse e. Call service No lamp, fan runs a. Burned-out lamp a. Replace lamp b. Lamp changer not engaged b. Slide changer arm into position c. Lamp not seated in recept
Summary of the content on the page No. 18
OPTIONAL ACCESSORIES SF MODELS ENX LAMP 360W/82V 456-188 (Models 3000/3010) FXL LAMP SOFT SHOULDER BAG ROLL FILM 410W/82V (PADDED) ADAPTER KIT 456-192 (Models 4010, 4030, 5500, 6000) 128-46 438-814 HARD-SIDED CARRYING CASE ATA SHIPPING CASE ACETATE ROLL (50') 185-398 185-397 310-6 To order accessories, please call 1-800-676-2487. PROTECTIVE DUST COVER 128-61 12
Summary of the content on the page No. 19
OPTIONAL ACCESSORIES HD MODELS ENX LAMP 360W/82V 456-188 (Models 3000/3010) FXL LAMP SOFT SHOULDER BAG ROLL FILM 410W/82V (PADDED) ADAPTER KIT 456-192 (Models 4010, 4030, 5500, 6000) 128-1 438-814 HARD-SIDED CARRYING CASE ATA SHIPPING CASE 185-385 185-397 To order accessories, please call 1-800-676-2487. 13
Summary of the content on the page No. 20
Part # 401-545-05
