Summary of the content on the page No. 1
MP7730 Multimedia Projector
Operator’s Guide
MP7730 Projecteur multimédia Guide de l’opérateur
MP7730 Multimedia-Projektor Benutzerhandbuch
Proyector de Multimedia MP7730 Manual del Usuario
MP7730 Proiettore Multimediale Manuale dell’operatore
MP7730 Bruksanvisning för multimediaprojektor
MP7730 Multimedia Projector Gebruiksaanwijzing
™
© 3M IPC 2000 3M Multimedia Projector MP7730
1
Lock
DLP
A TEXAS INSTRUMENTS PRODUCT
MP7630
Summary of the content on the page No. 2
™ 3M Multimedia Projector MP7730 © 3M IPC 2000 2
Summary of the content on the page No. 3
Table of Contents Please click on any section to jump to that section Introduction Safeguards .................................................................................... 4 Thank You for Choosing 3M .......................................................... 6 Warranty ........................................................................................ 6 Shipping Box Contents .................................................................. 7 Optional Accessories ....................
Summary of the content on the page No. 4
Introduction Intended Use Before operating the machine, please read the entire manual thoroughly. The 3M Multimedia Projector MP7730 was designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe o
Summary of the content on the page No. 5
L-Click + Magnify - Mute Introduction Product Safety Labels The following safety labels are used on or within the MP7730 projector to alert you to items or areas requiring your attention. Tested To Comply With FCC Standards Model No.: FP850 FOR HOME OR OFFICE USE This device complies with part 15 of the FCC Rules. Rating: ~100-240V, 50-60Hz, 2A Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferenc
Summary of the content on the page No. 6
Introduction Thank You for Choosing 3M Thank you for choosing 3M multimedia projection equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions. Warranty Limited Warranty 3M warrants this product against
Summary of the content on the page No. 7
T T L T P O T A EXA S I N SD RU ME N S P R DUC MP 30 76 R-Click + Volume - Introduction Shipping Box Contents ™ The 3M MP7730 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC, ™ Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Power Cord VGA MP7730 Multimedia Remote Control Mac 2-prong US, UK, Cable Projector Transmitte
Summary of the content on the page No. 8
L-Click + Magnify - Mute Introduction Part Identification 2 1 3 4 5 6 7 8 9 12 11 10 14 Laser Standby/On Source Menu Exit Freeze Blank Drag Ch Down Ch Up Reverse 13 2 1 3 5 4 6 8 7 9 + 0 /- Add/Erase Scan 1. Standby/On Button 8. Projection Lens 2. External Control Pad 9. Height Adjustment Feet 3. Remote Control Sensor 10. AC Power Cord Input 4. Carrying Handle 11. Serial Port Terminal Connection 5. Image Tilt Control 12. Mouse Control Port (Serial • PS/2 • ADB) 6. Kensington Lock
Summary of the content on the page No. 9
Introduction Machine Characteristics ™ ™ The MP7730 Multimedia Projector integrates ultra-high bright lamp and TI DLP technology into a single unit. The MP7730 Multimedia Projector offers the following features: • Small and portable unit • Full function remote control • Easy to set up and use • Digital keystone correction • XGA resolution and component video compatible • IR remote control sensor on top • Horizontal and vertical image inverting • On screen menus in seven languages • Horizontal an
Summary of the content on the page No. 10
L-Click + Magnify - Mute Introduction Remote Control Identification Source Press button to change input source. Standby/On Laser Press STANDBY/ON button to begin Press button to turn on the Laser Pointer projection mode (lamp on). To turn lamp off, press STANDBY/ON, then select YES Exit on Shutdown screen. Select NO to Press button to exit menu screens. Laser Standby/On continue running. Source Menu Exit Menu Selection Arrows Menu Press buttons to change between the four Press to display the men
Summary of the content on the page No. 11
+ Magnify - Introduction Remote Control Features The remote control sensor is located near the back of the projector. The distance between the sensor and the remote control unit must be shorter than 4 meters (13 feet). Freeze The image will be frozen when the FREEZE button is pressed. A “Pause” icon appears at the lower right of the screen for three seconds during the freeze function. A “Play” icon appears at the lower right of the screen for three seconds when the freeze function is released. T
Summary of the content on the page No. 12
Introduction Laser Press this button to generate the laser beam that functions as a red pointer on the screen. Laser button Disk Pad If the PS/2 (ADB) mouse cable is connected with the PC Notebook or Mac Powerbook mouse port, the Disk Pad can take over the Notebook or Powerbook mouse function. When the MAGNIFY function is activated, use the Disk Pad to move around the display areas. Note: The mouse function is not available when the MAGNIFY function is turned on. Disk Pad button R-Click, L-Clic
Summary of the content on the page No. 13
System Setup Screen Chart Place the projector at the required distance from the screen according to the desired picture size (see the table below). MP7730 PROJECTOR-TO-SCREEN DISTANCES Distance to Screen Screen Size Minimum Maximum Diagonal Width Height 6.0 ft. 8.0 ft. 40.0 in. 32.0 in. 24.0 in. Lens center 1.8 m 2.4 m 101.6 cm 81.3 cm 61.0 cm 9.0 ft. 12.0 ft. 60.0 in. 48.0 in. 36.0 in. 2.7 m 3.7 m 152.4 cm 121.9 cm 91.4 cm 12.0 ft. 16.0 ft. 80.0 in. 64.0 in. 48.0 in. 3.7 m 4.9 m 203.2 cm 162.6
Summary of the content on the page No. 14
MOUSE VIDEO System Setup Connecting to Various Equipment ™ It only takes a few minutes to connect the 3M Multimedia Projector MP7730 to your computer, VCR, or other device. Caution Turn off power to all devices before making connections. Never plug anything into the projector or computer while any device is in operation. The MP7730 must be powered down when making connections. The mouse emulation may not work if the unit is not powered down before the mouse cable connections are made. Connection
Summary of the content on the page No. 15
System Setup Mouse Connection General cable The general cable links the projector to the proper mouse adapter cable for your computer. 1. Attach the male Mini-DIN end of the general cable to the Mouse port on the rear of the projector. 2. Attach the female Mini-DIN end of the general cable to the end of the proper mouse adapter cable for your computer (serial, PS/2 or ADB cable). Line up the Female Mini-DIN Male Mini-DIN arrows on the sides of the plugs before attaching. Be sure not to bend or b
Summary of the content on the page No. 16
Operation Startup Ground lead 1 The 2-prong adapter with ground is used with Power older U.S. electrical outlets that only support 2-prong power cord plugs. Note: Make all cable connections and line Note: When using this adapter, the hookups with the ground lead MUST be securely power off. fastened to the ground screw on the outlet. Plug the 2-prong adapter into the bottom socket of the eletrical outlet. Hook the end of the ground lead firmly around the neck of the outlet’s ground 2 screw.
Summary of the content on the page No. 17
Operation Main Menu Press “Menu” key and the main menu will display on the screen. Press “Menu” again to enter page items, and press and to select sub-menus. The main menu will go off automatically if there is no further action from user for 10 seconds. Press EXIT button to leave the current sub-menu, and press EXIT again to leave the main menu. Menu Pages MENU } BAR MENU Display Menus Image Menus Control Menus Source Menus LAYOUT Auto Size Language Keystone Without Horizontal Phase Mirr
Summary of the content on the page No. 18
Operation DLP A TEXAS INSTRUMENTS PRODUCT Menu Exit MP7630 Keystone Keystone 0 0 Brightness 50 Brightness 50 Menu MENU EXIT 50 STANDBY/ON Contrast Contrast 50 Color Balance 1 Color Balance 1 Menu Exit MENU EXIT To Menu Items Menu 1 Menu Keystone x2 Keystone 0 0 50 Brightness Brightness 50 50 50 Contrast Contrast Color Balance 1 1 Color Balance Display Menu ™ 3M Multimedia Projector MP7730 © 3M IPC 2000 18
Summary of the content on the page No. 19
Operation Display Menu Keystone (0-255) 128 160 128 96 Brightness (0-255) 65 128 193 Contrast (0-255) 65 193 128 Color Balance (0-2) 0 2 1 ™ © 3M IPC 2000 3M Multimedia Projector MP7730 19
Summary of the content on the page No. 20
Operation Image Menu To Menu Items Menu 1 Off On Auto Resize Off On Auto Resize x1 Menu H.Phase 31 H.Phase 31 Menu 2 127 H.Size 127 H.Size x1 Menu 165 H.Position 165 H.Position Menu 3 x1 V.Position 105 Menu V.Position 105 Auto Resize Will automatically adjust image to fit onto screen. Off On Horizontal Phase (Auto Resize OFF) (0-31) Horizontal Size (Auto Resize OFF) 193 65 (0-255) Horizontal Position Vertical Position (Auto Resize OFF) (Auto Resize OFF) (0-255) (0-255) 65 193 193 65 ™ 3M Multime
