Summary of the content on the page No. 1
USER’S MANUAL
TM
10V 14V
10/14 ppm page printer
Summary of the content on the page No. 2
Federal Communications Commission Notice to American Radio Frequency Interference Statement Users Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
Summary of the content on the page No. 3
In case that the interface board, Ethernet C, is installed, this equipment complies with EMI regulations as follows: Federal Communications Commission Notice to American Radio Frequency Interference Statement Users Notice: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial enviro
Summary of the content on the page No. 4
SM As an International ENERGY STAR Partner, Fujitsu Limited has determined that this product meets the International ENERGY STAR Office Equipment Program for energy efficiency. The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipments. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which b
Summary of the content on the page No. 5
FM-4 User’s Manual
Summary of the content on the page No. 6
The contents of this manual may be revised without prior notice and without obligation to incorporate changes and improvements into units already shipped. Fujitsu has made every effort to ensure that the information included here is complete and accurate at the time of publication. The company assumes no liability for errors and omissions. Copyright © 1996 Fujitsu Limited Printed in Japan. All rights reserved. No part of this manual may be reproduced or translated, stored in a database or ret
Summary of the content on the page No. 7
Precautions Read this section and remember these instructions to ensure your safety and your printer’s correct performance. Follow the cautions and notices labeled on the printer or marked with icons in the manual. Save this manual for future reference. • Use only the power cord furnished with the printer and a properly grounded outlet. Do not use an extension power cord. • Confirm that the rated voltage of your printer matches the voltage of your power outlet. The maximum wattage of the pr
Summary of the content on the page No. 8
Contents Preface ............................................................................................ v Manual and Floppy Disks................................................................. v Operating Environments ................................................................. vi Conventions .................................................................................... vi Control Panel...........................................................................vii Chapter 1 Get
Summary of the content on the page No. 9
Contents Chapter 2 Using Printer Software ............................................................... 2–1 Remote Setup Utility Program, PPMENU .................................. 2–1 Installing PPMENU ............................................................. 2–2 Factory Defaults .................................................................... 2–4 Printer Management Utility Program, Lexmark’s MarkVision ..... 2–6 Installing MarkVision ...................................................
Summary of the content on the page No. 10
Contents Chapter 4 Enhancing and Customizing the Printer ..................................... 4–1 Adding RAM ............................................................................... 4–1 Installing an Alternate Emulation ................................................ 4–3 Installing an Interface Expansion Board....................................... 4–4 Installing an Interface Board ................................................. 4–4 Connecting to the Serial Port ......................
Summary of the content on the page No. 11
Contents Chapter 6 Solving Problems ....................................................................... 6–1 Clearing Paper Jams .................................................................... 6–1 Operational Problems .................................................................. 6–8 Print Quality Problems ................................................................ 6–9 Error Indications ....................................................................... 6–11 Action-required
Summary of the content on the page No. 12
Preface Thank you for purchasing the Fujitsu PrintPartner 10V/14V Page Printer. The PrintPartner 10V is a 10-ppm, 600-dpi, laser printer. The PrintPartner 14V is a 14-ppm, 600-dpi, laser printer. The PrintPartner 10V/14V is compatible with the HP LaserJet 4 printers, which are an industry-standard page printers. Available options are: • 1-, 2-, 4-, 8-, 16-, and 32-megabyte memory expansion cards • FPS card: PostScript level 2 compatible emulation • Interface expansion boards: serial interface, L
Summary of the content on the page No. 13
Organization Operating To run the Printer Driver, you need an IBM PC/AT or PS/2 computer or compatible running MS-Windows 3.1/3.11 or MS- Environments Windows 95. To run MarkVision, you need an IBM PC/AT or PS/2 computer or compatible running MS-Windows 95 (not MS-Windows 3.1/3.11), with at least 5MB of memory available on a hard disk, a 3.5" double- sided high density (2HD) floppy disk drive, and a VGA (640 × 480 dots) or higher resolution display. To run the Network Printer Utility, you need a
Summary of the content on the page No. 14
Control Panel The printer’s control panel incorporates two rows of buttons, with each button having one or two labels (see below). The physical button is beneath the rectangular section of no-labeled space. The top label represents the basic function, which is activated by a touch of the button. The bottom label represents the second function, which is activated when you release the button after holding it down more than five seconds. FORM + Basic functions READY FEED MENU Physical buttons RESET
Summary of the content on the page No. 15
viii User’s Manual
Summary of the content on the page No. 16
CHAPTER GETTING STARTED Getting Started 1 This chapter provides complete setup instructions in the following sections: •Getting Acquainted. Learning the printer’s main parts and its paper paths. •Getting Ready. Choosing a suitable location and unpacking the printer. •Setting Up. Assembling the printer. •Connecting the Printer. Selecting an interface and connecting to the computer. •Installing the Printer Driver. •Printing Your First Document. •Where to Go from Here. Getting The illustrations on
Summary of the content on the page No. 17
Getting Acquainted Stacker-full sensor Top cover Control panel (Paper stacker) Upper door Slide cover (Font/emulation card slot Front cover and RAM card slots inside) Manual feed slot (inside the cover) Paper tray Multi-function feeder connector Figure 1–1 Front and right side view Interface board Rear stacker slot cover Power switch Centronics parallel interface connector Power cord connector Figure 1–2 Rear and left side view 1-2 User’s Manual
Summary of the content on the page No. 18
Getting Acquainted Toner bottle GETTING STARTED Print density dial Print unit Figure 1–3 Interior view The path from the paper tray to the top cover is for ordinary paper. The straight path from the manual feed slot or optional multi- function feeder to the rear stacker is for transparencies and envelopes. Top cover (main stacker) Manual Rear feed stacker slot Paper tray From optional paper tray Figure 1–4 Paper paths User’s Manual 1-3
Summary of the content on the page No. 19
Getting Ready Getting Ready This section will help you: • Choose a suitable location for the printer • Inventory the parts of the printer as you unpack it Picking a Suitable Location The first step is to pick a suitable location for your printer. For peak performance and usability, follow these guidelines: • Place the printer on a sturdy, level surface. • Choose a room that is well ventilated and free of excessive dust. Leave space on either side of the printer for proper ventilation. • To avoid
Summary of the content on the page No. 20
Getting Ready • Use only the power cord GETTING furnished with the printer. STARTED Do not use an extension cord. • Do not touch any connector contacts and corona wires to avoid possible electrostatic damage to the printer. • Do not use a circuit shared with equipment that causes electrical noise, such as motors. • Do not use a circuit shared with equipment that uses a lot of power, such as a copier or a coffee maker. Unpacking and Checking Your Printer As you unpack the printer, check each item
