Summary of the content on the page No. 1
SP-200E
Statement Printer
User’s Guide
Version 1.00
7/2006
Edition 1
Copyright © 2006 ZyXEL Communications Corporation. All rights reserved.
Summary of the content on the page No. 2
SP-200E User’s Start Guide 1 Introducing the SP-200E The SP-200E is a 2-inch thermal printer with an integrated, easy-to-use, push-button control panel. It lets you generate subscriber accounts and print account information with the push of a button. It is also compact and portable and does not need a computer or printer. It is ideal for offices, coffee shops, libraries, hotels and airport terminals that provide Internet access for customers. You can connect multiple SP-200Es to a single hot
Summary of the content on the page No. 3
SP-200E User’s Start Guide 2.2 Rear Panel 1 Reset button 2 Power switch 3 DC power socket 4 Ethernet port (RJ-45) 5 PS/2 keypad port 1 2 3 4 5 Table 1 Rear Panel Hardware Label Description RST Press this button for 10 seconds to restore the factory default settings. The default IP address is 192.168.1.1. ON OFF Use this power switch to turn the printer on or off. DC Use the printer’s included power adaptor to connect this power socket to a power supply. POE RJ-45 port U
Summary of the content on the page No. 4
SP-200E User’s Start Guide 2.3 Front Panel Push-Buttons Push the power switch to ON. The buttons on the front panel light up when the statement printer is receiving power. The following table describes push-button’s LED status and functions. Note: If the printer prints continuously for two minutes, you must stop printing for at least eight minutes. Table 2 Front Panel Push-Buttons LED Status Printer mode Function All Button Off All of the printer’s functions are stopped. LEDs Off Hold button
Summary of the content on the page No. 5
SP-200E User’s Start Guide 3 Set a paper roll in the printer so that it unrolls 4 Pull some paper out to start the roll. from the bottom. Press down on the middle of the cover to close it (do not press on only one side of the cover). Press firmly until you feel the cover lock into the closed position. 5 Hold button A down to print a self-test. Pull the paper down across the tear bar from one side to the other to cut it. 4 Web Configurator The web configurator allows you to change the SP-200
Summary of the content on the page No. 6
SP-200E User’s Start Guide • Click Setup to log in if you want to configure the SP-200E (see section 4.2). • Click Firmware Upgrade if you want to upload firmware (see section 4.3). Note: The SP-200E automatically logs you out if there is no activity for longer than five minutes after you log in. If this happens, simply log back in again. 4.2 Configuration The Setup screen displays after you enter the user name and password and click Setup. 6
Summary of the content on the page No. 7
SP-200E User’s Start Guide Table 3 Setup Screen LABEL DESCRIPTION IP Address The SP-200E uses a static IP address. Enter the IP address in dotted decimal notation. The default is 192.168.1.7. You must also enter it in the hotspot or service gateway. Subnet Mask Enter the subnet mask in dotted decimal notation. The default is 255.255.255.0. Destination IP address Enter the IP address of the hotspot or service gateway. Port Enter the port number that the SP-200E uses when communicating with
Summary of the content on the page No. 8
SP-200E User’s Start Guide After you enter the user name and password and click Firmware Upgrade in the login screen, you need to wait a moment and click Continue to display the Firmware Upgrade screen. Specify the name of the firmware file in the Local PC File Path field or click Browse to locate the file and click Apply to start the file transfer process. The firmware must be a binary file and should have a .bin extension. Note: WARNING! Do not close the browser or disconnect or turn off th
Summary of the content on the page No. 9
SP-200E User’s Start Guide Paper Width 58(+0/-1) mm Printing Width 48 mm Paper Length 50 m max. Number of Statements Per Paper A single account statement is around 15 cm in length. You should be able to Roll print about 333 account statements on a 50 m paper roll. Paper Roll Outside Diameter 63(+2/-2) mm Paper Roll Inside Diameter 12(+0.5/-0) mm Printing Speed 25.4 mm / second Dot Resolution 8 dots / mm (203 dpi) Dot Configuration 384 dots / line Paper Detection Photo interrupter Thermal Head
Summary of the content on the page No. 10
SP-200E User’s Start Guide 6 Troubleshooting Table 5 Troubleshooting Problem Corrective Action The push-button Make sure that you have the correct power adaptor connected to the printer and plugged in LEDs are off. to an appropriate power source. Check all cable connections. If the front panel button LEDs still do not turn on, you may have a hardware problem. In this case, you should contact your local vendor. I cannot print the Check that the statement printer is connected to the gateway.
Summary of the content on the page No. 11
SP-200E User’s Start Guide • Never disassemble the printer or the adapter. • Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. • Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. • This product is recyclable. Dispose of it properly. 8 Procedure to View a Product’s Certification(s) 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the Zy
