Summary of the content on the page No. 1
May 2008
701P48331
8265/8290/8365/8390
Wide Format Color Printer
User Guide
Summary of the content on the page No. 2
Summary of the content on the page No. 3
COPYRIGHT NOTICE COPYRIGHT © 2008 Xerox. All rights reserved. This document may not be reproduced by any means, in whole or in part, without written permission of the copyright owner. This document is furnished to support the Xerox 8265/8290/8365/8390 Wide Format Color Printer Series. In consideration of the furnishing of the information contained in this document, the party to whom it is given, assumes its custody and control and agrees to the following: The information h
Summary of the content on the page No. 4
This page has been intentionally left blank.
Summary of the content on the page No. 5
TABLE OF CONTENTS 1 Safety Instructions..................................................................................................... 1 1.1 Introduction ........................................................................................................... 1 1.2 Warnings, Cautions and Notes ............................................................................. 1 1.3 Important Safety Instructions ...........................................................................
Summary of the content on the page No. 6
4.3.1 Setup Menu 1/7 ............................................................................................. 41 4.3.2 Setup Menu 2/7 ............................................................................................. 53 4.3.3 Setup Menu 3/7 ............................................................................................. 63 4.3.4 Setup Menu 4/7 ............................................................................................. 67 4.3.5 Setup Menu 5/7 .
Summary of the content on the page No. 7
6.6.2 Cleaning the Inside of the Printer................................................................. 128 6.6.3 Head Cleaning............................................................................................. 128 6.7 LongStore Procedure........................................................................................ 131 6.7.1 Ready the Printer for LongStore .................................................................. 131 6.7.2 Starting up after a LongStore.......
Summary of the content on the page No. 8
This page has been intentionally left blank. iv 8265/8290/8365/8390 User Guide
Summary of the content on the page No. 9
1 SAFETY INSTRUCTIONS 1.1 INTRODUCTION This chapter explains the meaning of safety terms for personnel who operate this equipment, important safety instructions, and the positions of the warning labels. Important Be sure to follow all instructions and warnings in this manual when using the equipment. 1.2 WARNINGS, CAUTIONS AND NOTES Safety terms in this manual and the contents of warning labels attached to the printer are categorized into the following three types depend
Summary of the content on the page No. 10
1 Safety Instructions Earth terminals for telephone line or lightening rod → Doing so may cause a large flow of voltage if lightening occurs. Water pipes or faucets → If there is a plastic part in the pipe, the earth will not work properly. • Do not insert or drop metal or inflammable objects into openings, such as ventilation outlets. Doing so may result in electrical shock and fire. • Stop using your printer if a liquid has been spilled into it. This may cause electrical shock or
Summary of the content on the page No. 11
1 Safety Instructions • Be careful not to pinch your fingers when opening and closing the cover of the ink compartment. • Be careful not to pinch your fingers when opening and closing the front cover. • Follow the instructions below when connecting the network interface cable. Otherwise, electrical shock or fire may occur. Do not touch the connector. Do not connect the network cable connector which has not the same specifications as the interface board. • When cutting the roll m
Summary of the content on the page No. 12
1 Safety Instructions 1.4 WARNING LABELS The handling, attachment locations, and types of warning labels are explained below. Warning labels are attached on areas which require attention. Read and understand the positions and contents thoroughly before performing your work. 1.4.1 Handling the Warning Labels Be sure to note the following when handling the labels. Notes • Make sure that all labels can be recognized. If text or illustrations cannot be seen clearly, either clea
Summary of the content on the page No. 13
1 Safety Instructions No Type 1 2 3 4 5 8265/8290/8365/8390 User Guide 5
Summary of the content on the page No. 14
1 Safety Instructions 6 7 8 9 6 8265/8290/8365/8390 User Guide
Summary of the content on the page No. 15
1 Safety Instructions 10 1.4.2.2 Location and Types of Warning Labels on the Rear of the Printer No Type 3 CAUTION THIS UNIT HAS TWO POWER SUPPLY CORDS, WHEN WINDING UNIT IS PROVIDED. TO REDUCE THE RISK OF ELECTRICAL SHOCK, DISCONNECT ALL POWER SUPPLY CORDS BEFORE SERVICING. 4 8265/8290/8365/8390 User Guide 7
Summary of the content on the page No. 16
1 Safety Instructions This page has been intentionally left blank. 8 8265/8290/8365/8390 User Guide
Summary of the content on the page No. 17
2 PRINTER OVERVIEW 2.1 FEATURES The features of the printer are explained below. (1) High speed output Achieve high speed printing, maximum media width of 2280 mm and printing width up to 2250 mm. (2) Wide variety of compatible media Adjustable head height can be adapted to various media thickness from 0.08 up to 1.1 mm. (3) Vibrant Colour Reproduction To reproduce sharp and vivid colour, either 4 or 6 ink colours are used for printing. Ink cassette come in either 220
Summary of the content on the page No. 18
2 Printer Overview 2.2 PART NAMES AND FUNCTIONS Part names and functions are explained below. 2.2.1 Front of Printer No Name Function 1 Heater plate Supports and heats the media during printing. Keeps the operator safe from the drive parts of the printer while it is operating. Only open and/or close the cover to perform following operations: 2 Front cover • Media setting and replacement • Cutter blade replacement • Cleaning the cleaning wiper 3 Carriage Drives and holds the
Summary of the content on the page No. 19
2 Printer Overview 2.2.2 Rear of Printer No Connection 1 Ethernet connector 2 Card reader slot 3 SmartChip label 4 Bracket Cover 5 Centronics connector Foot switch connector 6 7 Power inlet 8 Environmental label 9 DB-25 connector 10 ID label 8265/8290/8365/8390 User Guide 11
Summary of the content on the page No. 20
2 Printer Overview 2.2.3 Position and Function of the Heating Elements Heater element Temperature Function • Open the pores to make the media more receptive for Pre-heater (Heater A) 20 – 50°C 8365/8390 Mild Solvent Ink. • To establish optimum fixation onto the media (coated and Fixer (Heater B) 20 – 40°C uncoated). • Optimizes the dot gain control. • The post-fixer finalizes the fixation process and helps to Post-Fixer (Heater C) 20 – 70°C make the prints touch-dry. • The drye
