Summary of the content on the page No. 1
®
CX200
Desktop Label Printer
Summary of the content on the page No. 2
Section 1 General Information 1-1 Overview
!
"
#
#
#
$ CX
Summary of the content on the page No. 3
SECTION 1 - GENERAL INFORMATION 1-2 Dimensions D H W CX200DT CX200TT Weight 3.1lb./1.41 kg 3.6 lb./1.63 kg Depth 10 in. (254 mm) Heigth 6.6 in (168 mm) Width 6.9 in. (175 mm) ' Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 4
SECTION 1 - GENERAL INFORMATION 1-3 Specifications Model CX200DT/CX200TT Print Method Direct Thermal/Thermal Transfer Resolution 203 dpi 8 dpmm Max. Media Width 4.65 inches 118 mm Min Media Width 2.0 inches 51 mm Max. Print Width 4.1 inches 104 mm Max. Print Length 14 inches 356 mm Max. Print Speed 3 ips 76 mm/s Installed RAM 512 KB, non-volatile Installed ROM 512 KB, Flash Communications RS232C Serial and Centronics Parallel Max. Media Roll OD 5.0 inches 127 mm Ribbon 460 feet (140m) Wax, Wax/
Summary of the content on the page No. 5
SECTION 1 - GENERAL INFORMATION 1-4 Attributes TOP CASE READY INDICATOR ON-LINE/OFF LINE BUTTON FEED BUTTON PAPER GUIDE BOTTOM CASE FRONT CASE EXTERNAL MEDIA SERIAL FEED KNOCKOUT PORT PARALLEL PORT PLATEN ROLLER REMOVAL ACCESS SLOTS WALL MOUNTING SLOTS POWER CABLE POWER INPUT ROUTING CHANNEL ) Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 6
SECTION 1 - GENERAL INFORMATION 1-4 Attributes PAPER GUIDE (SHOWN WITH LABELS) PAPER GUIDE (SHOWN WITHOUT LABELS) RELEASE LEVERS FOR PRINT HEAD/RIBBON MECHANISM * Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 7
SECTION 1 - GENERAL INFORMATION 1-5 Controls, Indicators and Connections !
,
#
DEVICE NAME PRIMARY FUNCTION USE PRESS - to advance media PRESS while pressing READY FEED button Advances print media indicator-to print test label PRESS to pause printing during batch mode operation GREEN - Printer ready for data READY indicator Shows print status OFF - Printer busy, or Off-Line RED - Printer needs at
Summary of the content on the page No. 8
SECTION 1 - GENERAL INFORMATION 1-5 Controls, Indicators and Connections PIN # DESCRIPTION PIN # DESCRIPTION 1 Strobe 2 RXD (printer data input) 2-9 Data bits 0-7 3 TXD (printer data output) 10 Acknowledge 5 Ground 11 Busy 7 RTS (printer busy) 12 Out of paper 8 CTS 13 +5 VDC 1,9 +5 VDC, 200 mA max 14-15 No connection 17 Chassis ground 18 +5 VDC 31 Reset PARALLEL INPUT CONNECTOR 32 Error CENTRONICS 36 PIN SERIAL INPUT CONNECTOR DB9S 16,33 Signal Ground 19-30 34-36 No connection 18 1 1 5 BACK END
Summary of the content on the page No. 9
SECTION 1 - GENERAL INFORMATION 1-5 Controls, Indicators and Connections Printer Power Connection !
# !
'
# # Important! / #
!
#
!
/
Note:
Summary of the content on the page No. 10
SECTION 1 - GENERAL INFORMATION 1-5 Controls, Indicators and Connections Connecting the Interface Cable AVAILABLE DB9S PARALLEL PORT SERIAL PORT CONNECT THIS END OF THE PARALLEL CABLE TO THE CONNECT THIS END OF THE CENTRONICS 36 PIN CABLE PORT ON THE COMPUTER TO THE PARALLEL PORT ON THE PRINTER 0 Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 11
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Labels or Tags ALSO REFER TO THE ACCOMPANYING ILLUSTRATIONS (NEXT PAGE)
'
!
! !
( 2# 3 4 ) 5! ! ! !
! %
Summary of the content on the page No. 12
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Labels or Tags PRESS BACK THE RELEASES TO UNLOCK PAPER GUIDE MEDIA ROLL LIFT PRINT HEAD AND SLIDE UNDER MEDIA READY INDICATOR FEED BUTTON Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 13
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Ribbon '11
&&
" ( - ALSO REFER TO THE ACCOMPANYING ILLUSTRATIONS # '
!
! !
( 5! ! ! ):
Summary of the content on the page No. 14
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Ribbon (Continued) 1 % # !
!
!
!
'
( 7 2& !
899"
) &
-
Summary of the content on the page No. 15
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Ribbon (Continued) PLACE TAKE-UP CORE INTO LEFT TAKE-UP SPINDLE SUPPLY TAKE-UP KNOB CORE SPRING LOADED RIBBON TAKE-UP KNOB PRINT HEAD SUPPLY ROLL PULL THE RIBBON OVER THE PRINT HEAD TAKE-UP KNOB ) Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 16
SECTION 1 - GENERAL INFORMATION 1-6 Printer Setup Loading Ribbon (Continued) TURN RIBBON TAKE-UP KNOB CLOCKWISE TO ELIMINATE RIBBON SLACK LOWER THE PRINT HEAD AND PRESS DOWN FIRMLY ON BOTH HEAD LATCHES TO LOCK THE PRINT HEAD IN POSITION Selecting the Label Sensor Type '11
9%;
&
!
#
!
Summary of the content on the page No. 17
1-7 Printer Test and Calibration Preparation for Test
&
/
&
&
$ <
# < "
9" <
#
<
#
Summary of the content on the page No. 18
1-7 Printer Test and Calibration Preparation for Test 0
( (5#6 "
=
(%>'
#
# '
! 2# !
' ( ) ? 1
(-
+ @>
%
2
Summary of the content on the page No. 19
1-7 Printer Test and Calibration Print Head / Status Print
( 9 1 '
/
( 0 7( 8 (
& . Rev B SATO SERVICE MANUAL CX Series Printers
Summary of the content on the page No. 20
1-7 Printer Test and Calibration Change RS232 Settings
( 9 ' 2 '
/
0 Rev B SATO SERVICE MANUAL CX Series Printers
