Summary of the content on the page No. 1
Summary of the content on the page No. 2
This manual is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this manual. © 2007 Samsung Electronics Co., Ltd. All rights reserved. • ML-4050N is trademark of Samsung Electronics Co., Ltd. • Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd. • Centronics is a trademark of Centronics Data Computer Corpora
Summary of the content on the page No. 3
CONTACT SAMSUNG WORLD WIDE If you have any comments or questions regarding Samsung products, Country Customer Care Center Web Site contact the Samsung customer care center. LITHUANIA 8-800-77777 www.samsung.com/lt Country Customer Care Center Web Site LUXEMBURG 0032 (0)2 201 24 18 www.samsung.lu ARGENTINE 0800-333-3733 www.samsung.com/ar MALAYSIA 1800-88-9999 www.samsung.com/my AUSTRALIA 1300 362 603 www.samsung.com/au MEXICO 01-800-SAMSUNG www.samsung.com/mx BELGIUM 02 201 2418 www.samsung.co
Summary of the content on the page No. 4
CONTENTS 1. Introduction Special features ...................................................................................................................................................... 1.1 Printer overview ...................................................................................................................................................... 1.3 Finding more information ..........................................................................................................
Summary of the content on the page No. 5
9. Troubleshooting Clearing paper jams ................................................................................................................................................ 9.1 Troubleshooting checklist ........................................................................................................................................ 9.5 Understanding the status LED ....................................................................................................................
Summary of the content on the page No. 6
14 Adjust only those controls covered by the operating instructions. Safety and Regulatory Information Improper adjustment of other controls may result in damage, and may require extensive work by a qualified service technician to restore the machine to normal operation. Important Precautions and Safety Information 15 Avoid using this machine during a lightning storm. There may be a When using this machine, these basic safety precautions should always be remote risk of electric shock from l
Summary of the content on the page No. 7
When using this product, these basic safety precautions should always be Correct Disposal of This Product (Waste Electrical followed to reduce risk of fire, electric shock, and injury to persons: & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible ha
Summary of the content on the page No. 8
January 1, 1995: Council Directive 73/23/EEC Approximation of the laws of Canadian Radio Interference Regulations the member states related to low voltage equipment. This digital apparatus does not exceed the Class A limits for radio noise January 1, 1996: Council Directive 89/336/EEC (92/31/EEC), approximation emissions from digital apparatus as set out in the interference-causing of the laws of the Member States related to electromagnetic compatibility. equipment standard entitled “Digital
Summary of the content on the page No. 9
Wireless devices are not user serviceable. Do not modify Regulatory Compliance Statements them in any way. Modification to a wireless device will void the authorization to use it. Please contact manufacturer for Wireless Guidance service. Low power, Radio LAN type devices (radio frequency (RF) wireless Only use drivers approved for the country in which the device communication devices), operating in the 2.4 GHz/5 GHz Band, may be will be used. See the manufacturer System Restoration Kit,
Summary of the content on the page No. 10
EU Declaration of Conformity (R&TTE) We, Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. of #259, Gongdan-dong, Gumi-si Gyeongsanbuk-do [730-030] Korea of Samsung Electrinics Shandong Digital Printing Co., Ltd. Sanxing Road, Weihai Hi-Tech IDZ, Shandong Province 264209, China (factory name, address) declare under our sole responsibility that the product Laser Beam Printer model "ML-4050N" to which this declaration relates is in conformity with R&TTE Directive 1999/5/EC ( Annex IV ) L
Summary of the content on the page No. 11
Special features 1 Introduction Your new printer is equipped with several special features that improve Congratulations on the purchase of your printer! the print quality. You can: This chapter includes: Print with excellent quality and high speed • Special features • You can print up to 1200 x 1200 dpi effective • Printer overview output. See the Software section. • Finding more information a • Your printer prints A4-sized paper at up to 38 ppm • Selecting a location and letter-sized paper
Summary of the content on the page No. 12
Save time and money Use the optional hard disk • This printer allows you to use toner save mode to You can install an optional hard disk in your printer. save toner. See page 2.6. 1 2 • The 40 GB hard disk can store the data from your computer in the • You can print on both sides of the paper to save print queue. This decreases the workload of the computer. paper (double-sided printing). • You can use various print features, such as storing a job in the 3 4 • You can print multiple pages on
Summary of the content on the page No. 13
Rear view Printer overview Front view * The figure above shows an ML-4050N with all available options. 1 5 power switch parallel port 2 6 rear cover USB port 3 duplex unit 7 network port 4 power receptacle * The figure above shows an ML-4050N with all available options. 1 8 output tray handle 2 9 control panel paper level indicator 3 10 control board cover multi-purpose tray 4 11 tray 1 top cover 5 12 optional tray 2 output support 6 13 optional tray 3 multi-purpose tray paper width guides 7
Summary of the content on the page No. 14
Control panel overview Finding more information You can find information for setting up and using your printer from the following resources, either printed or onscreen. Quick Install Provides information on setting up your printer Guide and, therefore, be sure to follow the instructions in the guide to get the printer ready. Online User’s Provides you with step-by-step instructions for Guide using your printer’s full features, and contains information for maintaining your printer, trouble
Summary of the content on the page No. 15
Selecting a location Select a level, stable place with adequate space for air circulation. Allow extra space for opening covers and trays. The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the printer close to the edge of your desk or table. Clearance space Front: 482.6 mm (enough space so that trays can be opened or removed) Back: 320 mm (enough space to allow opening of the rear cover or the duplex unit) Right: 100 mm (e
Summary of the content on the page No. 16
Using control panel menus 2 System setup A number of menus are available to make it easy for you to change the This chapter shows menus you can set and provides basic settings for printer settings. The diagram on the next column shows the menus and your printer. all of the menu items available in each menu. The items in each menu and the options you can select are described in more detail in the tables This chapter includes: beginning on page 2.2. • Using control panel menus • Menu overvi
Summary of the content on the page No. 17
Note Menu overview • The default settings and available values of your printer could differ from this guide. The control panel menus are used to configure the printer. The control panel provides access to the foling menus. Job manager menu The menus in the colored characters appear only when the optional items are installed. This menu is available when the optional hard disk is installed. a Item Explanation 0.Job Manage. 1. Information (See page 10.7.) (See page 2.2.) Active Job This menu s
Summary of the content on the page No. 18
Layout menu Item Explanation Use the Layout menu to define all settings relating to output. Duplex In this menu, you can set the margins for double- Margin sided printing. You can increase or decrease the Item Explanation value in 0.1 mm increments. • Top Margin: Set the top margin. Orientation Choose the default orientation of the print image • Left Margin: Set the left margin. on the page. • Short Binding: Set the bottom margin of the back of the page for short binding. • Long Binding: Set
Summary of the content on the page No. 19
Graphic menu Item Explanation Use the Graphic menu to change settings affecting the quality of the Auto This item determines whether or not the printer printed characters and images. Continue continues printing when it detects the paper unmatched to your paper setting. Item Explanation • Off: If a paper mismatch occurs, an error message will remain on the display and the Resolution Specify the number of dots printed per inch (dpi). printer will remain off-line until you insert the The hi
Summary of the content on the page No. 20
PostScript Emulation menu This menu provides you with the Print PS Error menu item. Use the Emulation menu to configure printer language emulation. Item Explanation Item Explanation Print PS You can select whether your printer prints an error list Emulation The printer language defines how the computer Error when a PS error occurs. Type communicates with the printer. • Select On to print PS 3 emulation errors. If an error If you select Auto, your printer can change the occurs, the job stop
