Summary of the content on the page No. 1
® ® ® ® ® ®
Absolute COLOR • Absolute BLACK • Unidrums • Unirollers • Uniparts • Unicoatings
®
MINOLTA MAGICOLOR 5430 • 5440 • 5450
CARTRIDGE REMANUFACTURING INSTRUCTIONS
®
MINOLTA MAGICOLOR 5430
COLOR LASER PRINTER WITH TONER CARTRIDGE
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners.
Summary of the content on the page No. 2
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS ® MINOLTA MAGICOLOR 5430 TONER CARTRIDGE SIDE VIEW WITH END CAP SHOWN BACK VIEW OPPOSITE SIDE VIEW www.uninetimaging.com/technical.asp 11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com © 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show
Summary of the content on the page No. 3
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS SEPARATING THE CARTRIDGE 2. Cartridge separated. Set the drum unit and end cap aside. 1. Locate the cartridge end cap of the cartridge. We will now proceed to clean the toner hopper. Using a phillips screwdriver, remove the seven highlighted screws that hold the cartridge together. CLEANING THE TONER HOPPER 4. Using a small flathead screwdriver, carefully remove the fill 3. Locate the toner hopper fill plug. pl
Summary of the content on the page No. 4
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS SEPARATING THE DRUM UNIT 6. Locate the gear train side of the drum unit. 5. The drum unit (top) and developer unit (bottom) are joined together. Remove the OPC contact (highlighted). Now remove the gear train directly behind it. Note the position- ing of the gears. One of the gears is not removable. 7. After removing he gears, release the two screws that hold the 8. Drum axle plate removed. drum axle plate in
Summary of the content on the page No. 5
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 9. Release the compression spring on the opposite side of the 10. Locate the developer roller drive gear just below the OPC. drum unit (drive gear side). Using a phillips screwdriver, release the screw that holds it in Note: The compression springs are different, the longer spring is place. Note: this is a metric screw and will not fit anywhere else. connected to the gear train side of the drum and the small sp
Summary of the content on the page No. 6
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 13. Separate the two halves by first pulling out the developer DISASSEMBLING THE DRUM UNIT unit from where the pin was removed. Once it clears the waste 14. Remove the OPC drive gear support by first releasing the hopper section pull the two halves apart away from each other screw that holds the support plate in place. as shown 15. Once the screw has been removed, turn the support counter 16. Final position of
Summary of the content on the page No. 7
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS REMOVING THE OPC 18. Picture of OPC drum removed. 17. Once the OPC drive gear support plate has been removed, it will allow movement for the drum axle and will simplify the Note: It will not be necessary to remove the drum axle but it can removal of the OPC. easily removed by angling the axle and pulling it out of its sup- port. Note: the drum is secured on the axle with pressure. It will take some force to rem
Summary of the content on the page No. 8
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS REMOVING THE WIPER BLADE 22. Remove the wiper blade in the manner shown. 21. Remove the wiper blade by first disengaging the two screws (shown) that hold it in place. CLEANING THE WASTE HOPPER ASSEMBLING THE DRUM UNIT 23. Hopper shown with wiper blade completely removed. 24. Install the corona wire assembly via the gear train side first. Insert the corona wire assembly through the opening, then slide Dump the
Summary of the content on the page No. 9
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 25. Once the corona wire is aligned with the cartridge, Push it INSTALLING THE OPC with your finger tips until it is back into its original place. 26. Before inserting the OPC, make sure its gears are facing in the correct position. 27. Install the OPC drive gear support as shown. 28. Rotate the support clockwise until it locks into place. Once it locks it will need to be secured with its appropriate screw. www
Summary of the content on the page No. 10
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 29. Assemble the two halves by first inserting the drive gear. 30. Once that has been accomplished join the two halves and insert the pin on the gear train side. 31. Install the developer roller drive gear and its appropriate 32. On the opposite side, install the support plate and fasten screw. with two screw as shown. www.uninetimaging.com/technical.asp 11124 Washington Blvd., Culver City, California USA 90232
Summary of the content on the page No. 11
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 33. Once the two halves are assembled, continue installing the gear train and springs as shown. BEFORE AFTER REMOVING THE OEM CHIP ALTERING THE CHIP HOLDER 34. Locate the OEM chip on the inner portion of the end cap 35. Before installing the replacement chip, a small adjustment (shown). The chip has been fastened with a minimal amount of will need to be made to the chip holder shown. Two groove pat- pressure an
Summary of the content on the page No. 12
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 36. Aftermarket chip installed. 37. Install the drum contact as shown. ASSEMBLING THE END CAP 39. Install the transfer tube as shown. 38. Once the chip has been installed, you can proceed with installing the inner section of the end cap. www.uninetimaging.com/technical.asp 11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com ©
Summary of the content on the page No. 13
® UNINET IMAGING INC. • MINOLTA MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 40. Install the outer end cap. 41. Secure the end cap with the seven screws. NOTES www.uninetimaging.com/technical.asp 11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com © 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility o
