Summary of the content on the page No. 1
C780, C782
User’s Guide
October 2007
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,
registered in the United States and/or other countries.
© 2007 Lexmark International, Inc.
740 West New Circle Road
Lexington, Kentucky 40550
Summary of the content on the page No. 2
Edition: October 2007 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply t
Summary of the content on the page No. 3
Contents Chapter 1: Installing and removing options ..................................................................... 5 Installing a 2000-sheet drawer ......................................................................................................................... 6 Installing a 500-sheet drawer ........................................................................................................................... 8 Installing a duplex unit ........................................
Summary of the content on the page No. 4
Contents Print cartridges ............................................................................................................................................... 61 Toner waste container ................................................................................................................................... 62 Fuser and ITU ................................................................................................................................................ 62 Recyclin
Summary of the content on the page No. 5
1 Installing and removing options You can customize your printer memory capacity and connectivity by adding optional cards and input devices. You can also use these instructions to help you locate an option for removal. Install the printer and any options you have purchased in the following order: CAUTION: If you are installing options after setting up the printer, turn the printer off and unplug the power cord before continuing. • High capacity feeder (2000-sheet drawer) • Optional drawers •
Summary of the content on the page No. 6
Installing and removing options Installing a 2000-sheet drawer Your printer supports one optional 2000-sheet drawer. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. Note: The 2000-sheet drawer (High capacity feeder) does not conform to Ergonomics specification EK1- ITB 2006. 1 Unpack the 2000-sheet drawer and remove any packing material. 2 Place the drawer in the location you have chose
Summary of the content on the page No. 7
Installing and removing options 5 Install the power cord for the 2000-sheet drawer. Note: The HCIT power supply shall be capable of running off of AC line voltages from 90-256 VAC and from 47-63 Hz. The HCIT shall provide an IEC inlet power connector and an outlet power connector rated at 10 amperes. 2 1 3 6 Continue with Installing a 500-sheet drawer. Installing a 2000-sheet drawer 7
Summary of the content on the page No. 8
Installing and removing options Installing a 500-sheet drawer Your printer supports up to three additional 500-sheet drawers. However, if you install a 2000-sheet drawer, you can only add one additional 500-sheet drawer. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. 1 Unpack the 500-sheet drawer and remove any packing material. 2 Place the drawer in the location you have chosen for yo
Summary of the content on the page No. 9
Installing and removing options Installing a duplex unit Your printer supports an optional duplex unit that lets you print on both sides of a sheet of paper. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. 1 Unpack the duplex unit and remove any packing material. 2 Place the duplex unit in the location you have chosen for your printer or install it on a 500-sheet drawer. To install it o
Summary of the content on the page No. 10
Installing and removing options Installing the printer CAUTION: The printer weighs 48–82 kg (105–181 lb). It requires at least three (3) people to lift it safely. Use the printer handholds to lift it, do not lift by the front of the printer, and make sure your fingers are not under the printer when you set it down. 1 Unpack the printer. 2 Place the printer on the duplex unit or 500-sheet drawer: a Align the positioning posts on the duplex or 500-sheet drawer with the holes in the printer. b Lo
Summary of the content on the page No. 11
Installing and removing options Installing an output expander Your printer supports an optional output expander that lets you stack up to 650 sheets of paper in one bin. Note: After you unpack the output expander, install it immediately. Otherwise, the edges of the mounting brackets could damage tabletops or fabrics. 1 Unpack the output expander and remove any packing material. 2 Remove the printer top cover. Warning: The output expander tray is designed to hold the weight of print material on
Summary of the content on the page No. 12
Installing and removing options 4 Attach the printer top cover to the output expander. 5 Attach the output expander paper bail to the top cover. Installing an output expander 12
Summary of the content on the page No. 13
Installing and removing options Installing a 5-bin mailbox Your printer supports a 5-bin mailbox that lets you collate and stack up to 500 sheets of paper. Note: After you unpack the mailbox, install it immediately. Otherwise, the edges of the mounting brackets could damage tabletops or fabrics. 1 Unpack the mailbox and remove any packing material. 2 Remove the printer top cover. Warning: The mailbox is designed to hold the weight of print material only. Do not use it as a shelf; excess weight
Summary of the content on the page No. 14
Installing and removing options 4 Attach the printer top cover to the mailbox. 5 Attach the mailbox paper bail to the top cover. Installing a 5-bin mailbox 14
Summary of the content on the page No. 15
Installing and removing options Installing a StapleSmart finisher Your printer supports a StapleSmart finisher. See the information sheet included with the finisher for detailed installation instructions. Installing memory and option cards CAUTION: If you are installing memory or option cards sometime after setting up the printer, turn the printer off and unplug the power cord before continuing. If you have any other devices connected to the printer, turn them off as well and unplug any cabl
Summary of the content on the page No. 16
Installing and removing options Installing a memory card Follow the instructions in this section to install a printer memory card. Memory cards must have 100-pin connectors. Note: Memory cards designed for other Lexmark printers may not work with your printer. 1 Remove the system board access cover. For more information, see Removing the system board access cover. Warning: Memory cards are easily damaged by static electricity. Touch something metal on the printer before you touch a card. 2 Unpa
Summary of the content on the page No. 17
Installing and removing options Installing an “option-added” firmware card Follow the instructions in this section to install an optional “option-added” firmware or flash memory card. Note: “Option-added” firmware and flash memory cards offered for other Lexmark printers cannot be used with your printer. “Option-added” fiOnly one of each type of card is supported. Warning: “Option-added” firmware and flash memory cards are easily damaged by static electricity. Touch something metal on the prin
Summary of the content on the page No. 18
Installing and removing options Installing a hard disk Follow the instructions in this section to install an optional hard disk. You need a small flathead screwdriver to attach the hard disk to the mounting plate. Warning: Hard disks are easily damaged by static electricity. Touch something metal on the printer before you touch a disk. If an option card has been installed, you may need to remove it before installing the hard disk. 1 Remove the system board access cover. For more information, s
Summary of the content on the page No. 19
Installing and removing options 7 Press the ribbon cable connector into the connector on the system board. 8 Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board. The hard disk snaps into place. Installing memory and option cards 19
Summary of the content on the page No. 20
Installing and removing options Installing an option card Your printer has one expansion card slot that supports a number of option cards. The following table describes their function. Card Function MarkNet internal print server Adds an Ethernet or Token-Ring port so you can connect your printer to a network Parallel 1284-B Interface Card Adds a parallel port Serial Interface Card Adds a serial port Note: The network models ship with an integrated Ethernet print server already installed. Note:
