Summary of the content on the page No. 1
installation instructions
For Heavy Duty (FAS Models) and
Median (FAM Models) Air Conditioners
Please read ALL instructions before installing. Two people are
recommended to install this product. If a new electrical outlet
is required, have the outlet installed by a qualified electrician
before installing unit, See#5 in Preliminary Instructions
following.
Prelimi nary instru ctions
FOAM GASKET
Do the following before starting to install unit. See illustrations WASHERHEAD
below.
LOCKENG SCREW_._._
Summary of the content on the page No. 2
4. CHECK FOR ANYTHING THAT COULD BLOCK Tools Required AIRFLOW - check area outside of window for things such as shrubs, trees, or awnings. Inside, be sure a large flat blade screwdriver furniture, drapes, or blinds will not stop proper air flow. tape measure adjustable wrench or pliers 5. Check the available electrical service - power supply must pencil be the same as that shown on the unit serial nameplate. _/ Level _/ Socket wrenches (See Owner's Guide for serial plate Iocation.)Power cord _/
Summary of the content on the page No. 3
"ndow Mounting g Remove Chassis D Install Top Angle and Side Bracket 1. Pull down front panel and remove filter. (See FIG. 1). 1. Attach foam gasket to top angle above holes as 2. Lil_front upwards and place to one side. shown in FIG. 6. FIG. 6 2. Install top 3. Locate the four front screws and remove. These screws angle and will be needed to re-install the front later. (See FIG.2) side retainers 4. Pry away front from cabinet sides as per photo (see FIG .3) to cabinet as 5. Gently lift front of
Summary of the content on the page No. 4
3. Insert top and bottom legs of window filler panel M Install Support Bracket frame into channel in the to angle and bottom rail. Do both sides. 1. Hold each support bracket flush against outside of sill, 4. Insert washer head locking screws (2) into holes in and tight to bottom of cabinet as shown below. Mark top leg d filler panel frame (see Step 6). Do not brackets at top level of sill, and remove. totally tighten. Allow leg to slide freely. Screws will be tightened after Section 6. Place Ca
Summary of the content on the page No. 5
install Chassis into Extend Window Filler Cabinet and install ........... Panels Front to Unit 1. Carefully raise window to expose filler panel locking 1, Lift air conditioner and carefully slide into cabinet screws. Loosen screws so filler panels slide easily. leaving 6" protruding, 2. _DO not push on controls OR finned coils. 3, Be sure chassis is firmly seated towards rear of cabinet. 4. Installation of front is the reverse of removal outlined in Section 1. 2. Extend panels to fill window ope
Summary of the content on the page No. 6
Thru-The-Wall installation NOTE: Consult local building codes prior to installation, Carefully measure and cut an opening with the following or a qualified carpenter. dimensions depending on your model. See FIGS, land 2. WIDTH "X" = inside model width plus twice the thickness Select Wall Location of framing material used. HEIGHT "Y" = inside model height plus twice the thickness This air conditioner has a slide-out chassis, so that it can of framing material used. be installed through an outside
Summary of the content on the page No. 7
NOTE: If wall thickness is 8-1/2" or more, add aluminum flashing over bottom of frame opening to assure no water FIG. 2 can enter area between inner and outer wall. 1"LONG SCREW Refer to Step 4 d Window Mounting for assembly of support brackets.A wooden strip nailed to the outside ALUMINUM FLASHING OVER BOTTOM OF FRAME wall should be used in conjunction with sill support angle brackets. I Prepare and Install Cabinet 1. Slide chassis from cabinet. Refer back to Step 1 of Window Mounting. brakcet
Summary of the content on the page No. 8
OPTIONAL: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or hardware supply. On the outside, caulk openings around top and sides of cabinet, and all sides of wood sleeve to the opening. NOTE: See Step 7, Item 3 of Window Mounting Instructions for bottom rail seal location. Masonry Construction 1. Cut or build a wall opening in the masonry wall similar to the frame construction(refer to Step 2 d Thru-the-Wall Installation for a wall thickne
