Summary of the content on the page No. 1
®
EPSON Stylus Pro 7600/9600
Quick Reference Guide
®
EPSON Stylus Pro 7600/9600
Printed in USA
CPD-14020
Summary of the content on the page No. 2
1 Slide the removable paper stop off the left end of 7 Move the paper lever to the released position. the spindle. To use a 3-inch roll paper core, attach the gray adapters to the paper stops at each end. See your Printer Guide for details. 2 Position the roll paper as shown, then slide it onto the spindle. 8 Feed the paper into the slot and pull it all the way through. 3 Slide the removable paper stop back onto the spindle and insert it firmly into the end of the roll. 4 Open the roll paper cov
Summary of the content on the page No. 3
For heavy paper, you may need to increase 1 Make sure the printer is on and the roll paper the suction strength by pressing the button. cover is closed. This helps hold the paper in place during loading and printing. 2 Press the Paper Source button until the Sheet light comes on. For lightweight paper, decrease the suction by pressing the button. 3 Push the paper lever back to the released 5 position. Return the paper lever to the locked position. 6 Press the Pause button. The sheet feeds into
Summary of the content on the page No. 4
4 Open the front cover. (The cover has special tabs 7 Return the paper lever to the locked position. that act as paper supports when the cover is Then close the front cover. open.) 5 Feed the posterboard into the paper slot until it 8 Press the Pause button. The board feeds into meets resistance. the printing position automatically and READY appears on the control panel. If you’re using stock more than 39 inches long, load it long edge first (in landscape 9 Run your print job. After it is finish
Summary of the content on the page No. 5
If you notice banding or missing colors in your printouts, 4 Make sure all the Ink Out lights on the printer’s the print head may need cleaning. First print a nozzle control panel are off. If an Ink Out light is check pattern to find out the condition of the print head. flashing or on, you need to replace the Then run a cleaning cycle, if neccessary, and print another corresponding ink cartridge instead. check pattern to test the results. 5 Press the Cleaning button and hold it for at least 1 Lo
Summary of the content on the page No. 6
Before you begin a large print job, you should check your ink levels. If one of your cartridges is low, you can replace it before you start. Or you can wait until the ink runs out, replace the cartridge, and then continue the job without any loss of print quality. Checking Ink Levels (full) (almost empty) The easiest way of checking ink levels is from the control panel. black* black* cyan magenta light cyan light magenta yellow * If your printer uses EPSON UltraChrome™ ink, the black ink cartrid
Summary of the content on the page No. 7
When one of the Ink Out lights stays on and INK OUT 5 Hold the cartridge with the arrow mark pointing is displayed on the control panel, the cartridge is empty. toward the printer. Then insert the cartridge into To replace the cartridge, first make sure the printer is on. the slot. Don’t force it. 1 Open the ink compartment cover. If you can’t insert the cartridge smoothly, you may have the wrong cartridge. Check the package and product code. If the Ink Out light remains on after installing the
Summary of the content on the page No. 8
6 Insert the new cutter blade. Hold down its side Replacing the Cutter Blade pin and secure it with the latch. If you notice that the paper isn’t cut cleanly, you may need to replace the cutter blade. You can check its status 7 Close the printer cover. The carriage returns to as described below: the home position and the cutter replacement is complete. 1 Press the SelecType button on the control panel, then press until you see PRINTER STATUS. Replacing the Maintenance Tank The maintenance ta
Summary of the content on the page No. 9
Status messages These messages indicate normal phases of printer operation. Message Light Explanation or response READY Operate light on Printer is ready to print. PRINTING Operate light flashing Printer is receiving data. RESET All lights flash briefly Printer is resetting. PRESS PAUSE BUTTON Pause light on Press the Pause button to continue. WAIT Pause light on Printer is initializing, performing maintenance, or charging ink. PAUSE Pause light flashing Printer is paused. To resume printing, pr
Summary of the content on the page No. 10
Error messages (continued) Message Light Explanation Response PAPER JAM Paper Out light Paper has jammed in the Raise the paper lever and open flashing printer. the lower cover if necessary. Then remove the jammed paper, close the lower cover, and lower the lever. Turn the printer off and then back on. PAPER NOT STRAIGHT Paper Out light on Paper was fed at an angle. Reload paper, making sure the edges are straight and lined up with the row of holes. SERVICE REQ. All lights flashing An error has
Summary of the content on the page No. 11
CPD14020R1_Baf_QRG.qx 9/17/03 5:31 PM Page 1 ® EPSON S t y l u s P ro 7600/9600 Quick Reference Guide
