Summary of the content on the page No. 1
SPLIT TYPE ROOM AIR CONDITIONER
OWNER'S MANUAL
utions carefully and thoroughly before
From the Electrolux Group.
Summary of the content on the page No. 2
Contents Welcome to the world of simple handling and no worries. Safety precaution ................................................................................. 03 Thank you for choosing Frigidaire. This manual contains all of the information required to guarantee your safety and the appropriate use of Installation ........................................................................................... 07 your air conditioner. Part list ....................................................
Summary of the content on the page No. 3
Safety precautions 9. Do not drink water drained from To prevent injury to the user or other people and property damage, the following instructions must be followed. air conditioner. It contains contaminants and Incorrect operation due to ignoring of instructions may cause harm or damage. could make you sick. The seriousness is classified by the following indications. 10. Do not use the power cord close to heating appliances. It may cause fire and electric 1. Connect with the power properly. sho
Summary of the content on the page No. 4
19.Donotclean theairconditioner 27.Donotusestrong detergent such withwater. aswaxorthinner. Usea softcloth Water mayenter theunitand forcleaning. degrade theinsulation. Appearance maybedeteriorated Itmaycause anelectric shock. duetochange ofproduct coloror scratching ofitssurface. 20.Ventilate theroom wellwhenused 28.Ensure thattheinstallation bracket together withastove, etc. Anoxygen shortage mayoccur. oftheoutdoor appliance isnot damaged duetoprolonged 21.When theunitistobecleaned, exposure.
Summary of the content on the page No. 5
Installation Outdoor unit Choosing the installation site 1. The outdoor unit must be installed at a convenient site that is not exposed Precautions for installation to strong winds. The site should be dry and well ventilated. 2. The site must support the weight of the outdoor unit and allow for vertical Installation at the following sites may cause problems. If you must inevitably installation. install the unit at one of these sites, please consult your local distributor beforehand: 3. There mus
Summary of the content on the page No. 6
Part list more than 15cm_ Rndoorunit More than 12cm Air Filter <_ More than 60cm More than 30cm \ ......... J A More than 60cm Indoor unit B C More than 200cm Outdoor O Unit The indoor unit should be installed no lower than 2,3 m. The pipe needs the minimun of 4 or 5 meters, this distance will contribute to avoid vibration or noise. Two of the three direction above (A, B, C) should be not be blocker. The copper Outdoor unit pipe can be isolated independent.
Summary of the content on the page No. 7
Indoor unit installation Installation plate drilling and assembly Connective pipe and drainage installation _Do not block r//i Do not block Drainage 150mm or more to ceiling water flow _1 water flow Indoor unit outline Installationplate 1. Run the drain hose sloping downward. Do not install the drain hose as illustrated beside. f" ..... i 120ram or more to wall 2. When connection extension drain or more i _ o to wall ' _ oJ hose, insulate the connecting part Do not put the end of of extension dr
Summary of the content on the page No. 8
Outdoor unit installation 3. Piping can easily be made by lifting 1. Install the outdoor unit on a rigid the indoor unit with a cushion base to prevent increasing noise material between the indoor unit level and vibration. and the wall. Get it out after finish 2. Determine the air outlet direction piping. where the discharged air is not blocked. 4. Push the lower part of the Indoor Unit up on the wall. Then move the 3. In the case that the installation Indoor Unit from side to side, up place is
Summary of the content on the page No. 9
Refrigerant piping connection Settlement of outdoor Flaring work unitAnchor the outdoor unit with a Main cause for refrigerant leakage is bolt and nut 10 or 8 tightly due to defect in the flaring work. Air and horizontally on a concrete or Carry out correct flaring work sing the rigid mount. following procedure: Pipe 1. Cut the pipes and the cable. '_ All outlet A) Use the piping kit accessory or pipes purchased locally. B) Measure the distance between Right Wrong the indoor and the outdoor unit
Summary of the content on the page No. 10
Electrical work Electric safety regulations for the initial installation 4. Flaring work. A) Firmly hold copper pipe in a die 1. If there is serious safety problem 5. According to the attached Electrical in thedimension shown in the table about the power supply, the Connection Diagram located on the B'a_,__ Copper pipe technicians should refuse to install below. panel of the outdoor unit to connect ! the wire. the air conditioner and explain to Handle the client until the problem is 6. All wirin
Summary of the content on the page No. 11
Connect the cable to the indoor unit Connect the cable to the outdoor unit 1. Indoor/Outdoor connection cable 1. Remove the electric parts cover from should be H07RN-F type. the outdoor unit. 2. Remove the screw, then remove 2. Connect the connective cables to the over the window cover. terminals as identified with their respective matched numbers on the 3. Connect cables according to their terminal block of indoor and outdoor marks to terminals. units. 4. Wrap those cables not connected 3. To p
Summary of the content on the page No. 12
Caution: Air purging with vacuum pump After the confirmation of the above conditions, prepare the wiring as follows: 1. Check that each tube (both liquid and gas side tubes) between the indoor and outdoor units have been properly connected and all wiring for the test 1. Never fail to have an individual power circuit specifically for the air run has been completed. Remove the service valve caps from both the gas conditioner. As for the method of wiring, be guided by the circuit diagram and the li
Summary of the content on the page No. 13
Electricel sefety Using the vacuum pump Check the electrical safety before finalizing the installation. 1. The insulation resistance must be higher than 2Q. 1. Completely tighten the flare nuts, 7. Remove the charge hose from the 2. Grounding..After completing this step, measure its resistance with a tester. A, B, C, D, connect the manifold Low pressure charge hose. Confirm that the grounding resistance is lower than 4t_. valve charge hose to a charge port 8. Fully open the packed valve stems 3.
Summary of the content on the page No. 14
Test running Preparing the device for operation Perform test running after completing gas leak and electrical safety check. 1. Contact a specialist to install the device. The test running time should last more than 30 minutes. 2. Guarantee that the unit is appropriately fastened and complies with all of the aforementioned safety norms. 3. Check if all the functions works welt 1. Open the panel and lift the panel 3. Before operating the air conditioner, ensure that the air filter is installed up
Summary of the content on the page No. 15
Product description Display panel Front panel frame (indoor unit) Front panel Air filter infrared signal receptor (inside the front panel) Horizontal airflow grille Auto: When you set the air Vertical airflow louver conditioner to AUTO mode, the indoor temperature sensor indicator starts flashing. (inside the frontal panel) Defrost (only heating model): This Display panel indicator illuminates when the air infrared signal receiver conditioner starts defrosting Air inlet Connection for the drain
Summary of the content on the page No. 16
Remote control functions / .............................. Performance features Install / replace batteries i!iii iiii i ii i,i ' The remote controller uses two alkaline dry batteries (R03/LR03X2). 1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model 1. To install batteries, slide back the cover of the battery compartment and without) and FAN. install the batteries according to the directions (+and-) show on the remote controller. 2. Timer Setting Function in 24 hours. 2. To replace the
Summary of the content on the page No. 17
Remote control operations TEMP Button V : Push this button to decrease the indoor temperature setting. .MODE: Each time the button is pressed, the operation mode is shifted in the direction of the arrow: AUTO _ COLL I_ DRY I_ HEAT I_ FAN t * Note:COOL only model has no HEAT Display: cooling model Display: coolinglheating model feature. SWING: Push this switch button to change the louver angle. directional swing feature of the button is pressed, the fan speed horizontal louver is activated. The E
Summary of the content on the page No. 18
How the air conditioner works AUTOMATIC OPERATION COOL/HEAT (Cooling only model Switch on the power and the without) and FAN Operation, OPERATION indication lamp on the If the AUTO mode is not comfortable, display panel of the indoor unit starts you may manually over-ride the flashing, and turns off after flashes for settings by using COOL, HEAT or FAN 6 times. modes. 1. Use the MODE button to select 1. Push the TEMP button to set the AUTO. desired room temperature. When in 2. Push the TEMP butt
Summary of the content on the page No. 19
ECONOMIC mode TIMER Operation i 1°c I Push TIMER ON button to set the auto- on time and TIMER OFF button to set Press theECONOMIC keytoactive X,' _ 1 °C theECONOMIC mode. Press this the auto-off time. button again todeactivate it. E To set the starting time I _houri 1hour I 1. Push the TIMER ON button, then the remote controller shows TIMER ON, In the cold and dry modes: ECONOMIC operation - Cooling the last set time for the starting operation and the signal "h" will be shown - The indoor unit f
Summary of the content on the page No. 20
Adjusting air flow direction DRY Operation Adjust the air flow direction properly otherwise, it might cause discomfort The dry mode will automatically select or cause uneven room temperatures. the drying operation based on the Due to the difference of the set difference between the set Adjust the horizontal louver using the temperature of the unit and the actual remote controller. temperature and the actual room indoor temperature, the Air temperature.. The temperature is Adjust the vertical lou
