Summary of the content on the page No. 1
LQ-570/1070
Characterfonts:
I
Point 10.5 pl
! Fort1
I / Pitch / , , / Proptilonel
I
lo j
1 Epson !o
0
Epson Cower 1
Epson Roman
I
1 Epson
I
Epson
~ Epson Scnpt IO 0
I C I
Epson Orator
1 Epson Orator-S
I OCR-B
You can also select other font/pitch combinations using ESC/P 2
commands.
Scalable fonts:
Increments ~
Font 1 ]
Epson Roman I 32
Ribbon cartridge
Power cord
/ Epson Sans serif j8
( 32 ~ 2 Pt
Character tables: 1 italic and 5 graphics character tables
Character sets: 14 international
Summary of the content on the page No. 2
LQ-570/1070 Electrical lRbd5: 63.5 x 23.8 mm (2% x 15/16 inches) Size Rated voltage: AC 120 V (120 V model) 101 x 23.8 mm (4 x 15/16 inches) 101 x 27 mm (4 x 17/16 inches) Input voltage range: AC lcr3.5 to 132 V (120 V model) Thickness 0.07 to 0.09 mm (O.OM8 to 0.0031 inches) for Rated cuwen t: 2.0 A (120 V model) backing sheet 0.16 to 0.19 mm (O.OCKi3 to 0.0075 inches) total (during self-test printing in draft mode, Power cunsrrnption: l Use continuous type labels only. at 10 cpi) Approx. 33 W
Summary of the content on the page No. 3
LQ-570/1070 The Control Panel ALT While holding down this button, pressing certain other buttons The indicator lights give you the current status of the printer. The buttons let you control many of the printer settings. results in the following: BUFFER CLEAR (PAUSE) clears the printer’s buffer and intitializes ~~,~~~~~’ Sfzji? ? (LOAD/EJECT) feeds paper forward in l/ 180~inch I ’ J (LVFF) feed paper backward in 1 /lB@inch increments Lights Bin Sale&TEAR OFF This button selects the paper bin when
Summary of the content on the page No. 4
LQ-570/1070 Table 2 DlP switch 2 International character sets ON OFF / ASCII code (hex) DIP switch Page length (for I See Table 5 below i 2-2 ’ 23 24 40 50 SC SE 7C 7E l-l 1-2 [ 2-3 1 on Off / 0 USA # S a [ \ I A ’ 1 I ) - I Auto line feed on off t $ h l q 3 a 6 D ib OnOnOffOn 2 Germany ’ 6 D OnOtfOnOff! 3 E ( @ [ \ ] * ’ ( i ) - On Offj Table 3 ~ntemational character sets 4 Denmark I e t e A 0 A A * c 0 a - Oft Off I 1-l l-3 ; 14 5 Sweden # n B .& 0 A U 6 6 A ii I I On On Off
Summary of the content on the page No. 5
LQ-570/1070 Input buffer capacity Connector pin assignments and a description of their respective interface signals are shown in the following table. The printer stores print data sent from your computer in its input buffer. Keep DIP switch 1-7 off to select an BKbyte buffer. Signal ’ ) Pln ! c Skip-over-perforation 1 i 19 STROBE 1 IN STROBE pulse to read data. Pulse must be more than 0.5 1 at the ~ Turning DIP switch 1-8 on when you are using continuous paper enables the skipover-perforatio
Summary of the content on the page No. 6
LQ-570/1070 Paper: Interface timing I I sheets The figure below shows the timing for the parallel interface: I 1 Width I 182to216mm (7.17 to 8.50 1 , / 165 to 241 mm I 1 (7.17 to 8.50 Inches) (6.50 to 9.49 inches) ; 182to420mm I (7.17 to 16.54 inches) i mm ; / 182 to420 mm ( (7.1710 16.54 Inches) 1 (6.50 to 9.49 Inches) I ) Length I (8.27 to 12.00 Inches) j 0.07 to 0.10 mm 0.16 to 0.52 mm ~ (0.0028 to 0.0039 Inches) to 0.0205 inches) 64 to 82 ! 45 to 91 (17 to 22 Ibs) to 24 \ 0.5 + (Min.)
Summary of the content on the page No. 7
LQ-570/1070 Non-recommended Commands Information Reference List Epson recommends against using the following commands because some of these commands are not supported in existing printers and Engineering Change Notices some are duplicates of other commands. None. BEL Beeper BS Backspace Product Support Bulletins DC1 Select printer None. DC3 Deselect printer Technical Information Bulletins CAN Cancel data None. ESC # Cancel MSB control ESC< Unidirectional printing for one line Related Documentati
