Summary of the content on the page No. 1
DOT MATRIX PRINTER
MODEL
iDP3110
Summary of the content on the page No. 2
iDP3110 User's Manual Declaration of Conformity Manufacturer’s Name : : Japan CBM Corporation Manufacturer’s Address : CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo, 164-0001, Japan Declare the Product Product Name Dot Matrix Printer Model Number(s) iDP3110 Series (iDP3110R, iDP3110P) (S.No. 0090001 ~ ) Conform to the following Standards LVD : EN60950 : A4:1997 EMC : EN55022 : 1998 Class B : EN61000-3-2 : 1995+A1:1998+A2:1998 : EN61000-3-3 : 1995 : EN55024 : 1998 : EN61000-4-2 : 1995 – 4KV CD, –
Summary of the content on the page No. 3
iDP3110 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. * Do not use this product near water. * Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product. * Slots and openings on
Summary of the content on the page No. 4
iDP3110 User's Manual IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equ
Summary of the content on the page No. 5
iDP3110 User's Manual CONTENTS 1. INTRODUCTION ......................................................................................................................................... 1 1.1 Features ................................................................................................................................................................1 1.2 Accessories.........................................................................................................................
Summary of the content on the page No. 6
iDP3110 User's Manual 1. INTRODUCTION The iDP3110 is a dot-impact printer suitable for use with various data communication terminals, and measurement terminals. This product is extremely compact and features extensive functions suited for a wide range of applications. Please read this manual thoroughly to understand the printer before use. 1.1 Features 1. Compact desk-top dot matrix printer 2. Light weight 3. High speed printing 4. Low power consumption 1.2 Accessories The following attachment
Summary of the content on the page No. 7
iDP3110 User's Manual 2. TYPE CLASSIFICATIONS 2.1 Type The product is categorized according to the naming plan indicated below. iDP3110 24 P J 120 A 40 R F 230 B iDP3110 24 P J 120 A Model Name Printer cover Number of columns A : 60mm(Dia.) 24 : 24 columns/144 dots Paper roll 40 : 40 columns/180 dots B : 80mm(Dia.) Paper roll Power source 120 : AC 120V 230 : AC 220-240V Interface P : Parallel (Centronics) R : Serial (RS-232C) Character J : Japanese F : International 2.2 AC adapter Please use t
Summary of the content on the page No. 8
iDP3110 User's Manual 2.3 Specifications Item iDP3110-24* iDP3110-40* 1 Printing method Dot matrix 2 Printing direction One-way printing 3 Character configuration (5 + 1) × 8 (4 + 0.5) × 8 (W × H) 4 Number of columns per line 24 columns: 144 dot/line 40 columns: 180 dot/line 5 Printing speed Approx. 2.5 line/sec. Approx. 1.8 lines/sec. 6 Character size (W × H) 1.6 × 2.4 mm 1.08 × 2.4 mm 7 Line pitch 3.52 mm 8 Paper Paper Roll 57.5 ± 0.5(W) × 60 (Dia) mm 57.5 ± 0.5(W) × 80 (Dia) mm 9 Interface T
Summary of the content on the page No. 9
iDP3110 User's Manual 3. EXTERNAL APPEARANCE AND PART DESCRIPTION 3.1 External Appearance CITIZEN 4
Summary of the content on the page No. 10
iDP3110 User's Manual 3.2 Part Descriptions 1. DC Jack Insert the output plug of the AC adapter attached. 2. Power Switch When switched ON, power is supplied to the printer, starting the initializing operation. 3. Power Lamp Lighted when power is turned ON and goes out when turned OFF. 4. SEL Lamp Lighted when printer is in the selected condition (ON-LINE). Printer becomes operational only when this lamp is on. 5. LF Switch Paper is fed when switch is pressed (de-select condition only). Us
Summary of the content on the page No. 11
iDP3110 User's Manual 4. OPERATIONS 4.1 Connection of the AC Adapter (1) Ensure that the power switch is OFF. (2) Insert the output plug of the AC adapter into the DC jack of the printer. (3) Insert the power plug of the AC adapter into a power concent supplying the designated voltage. (Use of exclusive AC adapter is recommended. Output is DC 7V, 1.2A. Avoid using power sources not conforming to this specification.) CITIZEN 6
Summary of the content on the page No. 12
iDP3110 User's Manual 4.2 Setting of the Printer Cover (1) Hold the protruding section at the rear of the printer cover and lift in the direction indicated. (2) Attach the cover by pressing downward after hooking the cover to the acceptor located in the front part. CITIZEN 7
Summary of the content on the page No. 13
iDP3110 User's Manual 4.3 Setting of Ribbon Cassettes (1) Remove the printer cover after turning OFF the printer. (2) Press down on the Ribbon cassette while inserting the ribbon between the printing head and the platen. (3) Wind up the ribbon slack by turning the knob in the direction of the arrow. CITIZEN 8
Summary of the content on the page No. 14
iDP3110 User's Manual 4.4 Setting Paper (1) Remove the printer cover. (2) Ensure that the end of the paper is straight or incline as indicated in the diagram. (3) Insert the end of the paper into the slot of the printer mechanism. (4) After turning ON the printer, press the LF switch until 5 to 6 cm of paper is fed out of the printer mechanism. (5) Insert paper after moving aside the paper holder in the direction of the arrow. Then, secure the center of the roll with the holder. (6) Then, attac
Summary of the content on the page No. 15
iDP3110 User's Manual 4.5 Self Test Printing A self-printing function is incorporated in this product to enable the printer to check itself. This function is triggered by the following procedure. (1) Set paper to the printer. (2) Ensure that the ribbon cassette is attached correctly and turn the power OFF. (3) Turn ON the power switch while holding the LF switch down. Release the LF switch after the self-printing operation has started. Printing is initiated by this operation. To end self-printi
Summary of the content on the page No. 16
iDP3110 User's Manual 5. PARALLEL INTERFACE 5.1 Specifications a) Data input system : 8 bit parallel (DATA 1-8) b) Control signal : ACK, BUSY, STB, RESET, SELECT c) Compatible Connector : Printer side : 57LE-40360 (AMPHENOL or equivalent) : Cable side : 57-30360 (AMPHENOL or equivalent) 5.2 Connector Pin Assignment PIN SIGNAL NAME PIN SIGNAL NAME 1 STB 19 TWISTED PAIR GND 2DATA1 20 ″ 3 ″ 2 21 ″ 4 22 ″ 3 ″ 5 23 ″ 4 ″ 6 ″ 5 24 ″ 7 25 ″ 6 ″ 8 26 ″ 7 ″ 9 ″
Summary of the content on the page No. 17
iDP3110 User's Manual 5.3 Description of Input / Output Signals (1) Input signal All input signals utilize type 74HC of CMOS and can be used in TTL level as the input is pulled up with 3.3 kΩ resistance. - DATA 8 bit parallel signal (positive logic) - STB Strobe signal for reading out data (negative logic) - RESET Signal for resetting the entire unit (negative logic 4ms or more) (2) Output signal TTL is utilized for all output signals. The output is pulled up with 3.3 kΩ resistance.
Summary of the content on the page No. 18
iDP3110 User's Manual • Output [ Printer side ] [ Host side ] (4) Timing chart 1) Timing for data entry and printing T1 0.5 μs MIN T2, T3 1 μs MIN T4 2 μs TYPE (5) Data receiving Printer is capable of accepting data from the host while the BUSY signal is in the “LOW” state. Printer cannot accept data when the signal is “HIGH”. CITIZEN 13
Summary of the content on the page No. 19
iDP3110 User's Manual 6. SERIAL INTERFACE 6.1 Specifications 1) Synchronization : Asynchronous 2) Baud rate : User selection, 4,800; 9,600 Baud / sec 3) Word configuration : Start bit 1 bit : Data bit 8 bit : Stop bit More than 1 bit 4) Signal polarity RS-232C * Mark = Logic “1” (-3 to –12V) * Space = Logic “0” (+3 to +12V) TTL(RESET) * H level = Logic “1” (refer to (3), section 6.3) * L level = Logic “0” 5) Input control (DTR signal) * Mark : Data transmission not possible * S
Summary of the content on the page No. 20
iDP3110 User's Manual 6.2 Connector Pin Assignment SIGNAL SIGNAL SIGNAL DIRECTION FUNCTION RS232C TTL PIN NAME HOST-PRINTER 1 FG Frame ground 7 GND Signal ground 3RD Received data → 20 DTR Printer BUSY signal ← 23 RESET Printer reset signal → Note: 1. Signals for RS-232C are based on EIA RS-232C level. Applicable connector (D-Sub connector) Printer : 17LE-13250 (Anphenol equivalent) Cable : 17JE-23250 (Anphenol equivalent) 6.3 Description of Input / Output Signal (1) I / O signals 1) RD Se
