Summary of the content on the page No. 1
UPS
(40–80 kVA)
INSTALLATION & OPERATION MANUAL
www.powerware.com
Summary of the content on the page No. 2
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries. Please read all instructions before operating the equipment and save this manual for future reference. Consignes de sécurité CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS CE MANUEL CONTIENT DES CONSIGNES DE SÉCURITÉ IMPORTANTES ClassAEMCStatements FCC Part 15 NOTE Thisequipmenthasbeentestedandfoundtoc
Summary of the content on the page No. 3
Table of Contents 1Introduction............................................................ 1-1 1.1 Basic System Configurations................................................. 1-2 1.2 Using This Manual ......................................................... 1-3 1.3 Conventions Used in This Manual ............................................ 1-4 1.4 Safety Warnings ........................................................... 1-5 1.5 For More Information..........................................
Summary of the content on the page No. 4
TableofContents 5 Installing a Remote Emergency Power-Off Control ......................... 5-1 6 Installing Options and Accessories........................................ 6-1 6.1 Installing a Hot Sync Computer Area Network Bridge Card....................... 6-1 6.2 Preliminary Wiring Procedure ............................................... 6-2 6.3 Installing Parallel System Control Wiring ...................................... 6-3 6.4 Installing a Remote Monitor Panel ........................
Summary of the content on the page No. 5
TableofContents 8.1.6 LanSafe Power Management Software..................................... 8-2 8.1.7 Installation Features .................................................... 8-2 8.2 Options and Accessories.................................................... 8-2 8.2.1 Integrated Battery Cabinets.............................................. 8-2 8.2.2 Integrated Distribution Cabinet .......................................... 8-2 8.2.3 HotSync Parallel System....................................
Summary of the content on the page No. 6
TableofContents 10.2 Multiple Module Parallel Operation .......................................... 10-8 10.2.1 Starting the Parallel System in Normal Mode ............................... 10-8 10.2.2 Starting the Parallel System in Bypass Mode................................ 10-9 10.2.3 Transfer Parallel System from Normal to Bypass Mode....................... 10-10 10.2.4 Transfer Parallel System from Bypass to Normal Mode....................... 10-10 10.2.5 Single UPM Shutdown .................
Summary of the content on the page No. 7
TableofContents 15 Product Specifications................................................... 15-1 15.1 Model Numbers........................................................... 15-1 15.2 SingleModuleSpecifications ................................................15-1 15.2.1 UPS System Input ...................................................... 15-1 15.2.2 UPS System Output .................................................... 15-2 15.2.3 Environmental...............................................
Summary of the content on the page No. 8
List of Figures Figure 1-1. Powerware 9390 UPS (40–80 kVA) Cabinet..................................... 1-1 Figure 2-1. Powerware 9390 UPS (40–80 kVA) Cabinet as Shipped on Pallet................... 2-3 Figure 3-1. Removing Front Shipping Bracket on the Powerware 9390 UPS.................... 3-3 Figure 3-2. Removing Rear Shipping Bracket on the Powerware 9390 UPS .................... 3-4 Figure 5-1. REPO Control.............................................................. 5-1 Figure 6-1. Hot Sy
Summary of the content on the page No. 9
Figure 9-24. Change Password Screen ................................................... 9-19 Figure 9-25. Change Password Save Screen............................................... 9-20 Figure 9-26. Time Format Screen ....................................................... 9-21 Figure 9-27. Set Date and Time MM/DD/YYYY Screen...................................... 9-22 Figure 9-28. Date and Time DD/MM/YYYY Screen ......................................... 9-23 Figure 9-29. COM Port Setup Screen ..
Summary of the content on the page No. 10
This page intentionally left blank. ® viii Powerware 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C
Summary of the content on the page No. 11
Chapter 1 Introduction ® The Powerware 9390 uninterruptible power supply (UPS) is a true online, continuous-duty, transformerless, double-conversion, solid-state, three-phase system, providing conditioned and uninterruptible AC power to protect the customer’s load from all nine power failures. The Powerware 9390 UPS is available as a single module or a multiple module parallel system (see paragraph 1.1). The Powerware online power protection system is used to prevent loss of valuable electronic
Summary of the content on the page No. 12
Introduction 1.1 Basic System Configurations The following basic UPS system configurations are possible: Single module UPS and one to four battery cabinets Single module UPS, one to four battery cabinets, and an optional Integrated Distribution Cabinet (IDC) Hot Sync parallel system with two UPS modules, one to four battery cabinets for each UPS, and an optional module tie cabinet - One capacity/one redundant (1+1) - Two capacity (2+0) Hot Sync parallel system with three UPS modules, one
Summary of the content on the page No. 13
Introduction 1.2 Using This Manual This manual describes how to install and operate the Powerware 9390 UPS (40–80 kVA) cabinet. Read and understand the procedures described in this manual to ensure trouble-free installation and operation. In particular, be thoroughly familiar with the REPO procedure (see page 10-7). The information in this manual is divided into the sections and chapters listed. The system, options, and accessories being installed dictate which parts of this manual should be rea
Summary of the content on the page No. 14
Introduction Chapter 14, “Maintaining the UPS System” – contains maintenance instructions for the UPS system. Chapter 15, “Product Specifications” – provides detailed specifications for the UPS system. Appendix A, “Installation Information” – contains important information on wiring requirements and recommendations, and important diagrams of the cabinets’ mechanical details and electrical access. Warranty – provides the Powerware warranty for this product. Read through each procedure bef
Summary of the content on the page No. 15
Introduction 1.4 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read all instructions before operating the equipment and save this manual for future reference. The UPS cabinet is designed for industrial or computer room applications, and contains safety shields behind the doors. However, the UPS system is a sophisticated power system and
Summary of the content on the page No. 16
Introduction 1.5 For More Information Refer to the Powerware 9390 Integrated Battery Cabinet (Models IBC-S and IBC-L) Installation Manual (164201536) for the following additional information: Integrated Battery Cabinet (IBC) installation instructions, including site preparation, planning for installation, wiring, and safety information. Detailed illustrations of the cabinet, including dimension and connection point drawings. Refer to the Powerware 9390 Integrated Distribution Cabinet (80 kVA
Summary of the content on the page No. 17
Section I Installation ® 1-1 Powerware 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C
Summary of the content on the page No. 18
This page intentionally left blank. ® 1-2 Powerware 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C
Summary of the content on the page No. 19
Chapter 2 UPS Installation Plan and Unpacking Use the following basic sequence of steps to install the UPS: 1. Create an installation plan for the UPS system (Chapter 2). 2. Prepare your site for the UPS system (Chapter 2). 3. Inspect and unpack the UPS cabinet (Chapter 2). 4. Unload and install the UPS cabinet, and wire the system (Chapter 3). 5. Install features, accessories, or options, as applicable (Chapters 5 and 6). 6. Complete the Installation Checklist (Chapter 3). 7. Have authorized se
Summary of the content on the page No. 20
UPSInstallationPlanandUnpacking 2.2.1 Environmental Considerations The life of the UPS system is adversely affected if the installation does not meet the following guidelines: The system must be installed on a level floor suitable for computer or electronic equipment. The system must be installed in a temperature and humidity controlled indoor area free of conductive contaminants. Failure to follow guidelines may void your warranty. 2.2.2 Preparing for Wiring the UPS System For external wiri
