Summary of the content on the page No. 1
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 1
Owner’s Manual
®
SmartPro Rackmount
Intelligent, Line-Interactive UPS Systems
SMX500RT1U SMX750RT1U SMX1500XLRT2U SMX3000XLRT2U
• 230V Sine-Wave Input/Output 500VA - 3000VA Capacities
Extended-Run Options*
* SMX1500XLRT2U and SMX3000XLRT2U models
Important Safety Instructions 2
Mounting 3
Quick Installation 5
Optional Installation 6
Basic Operation
7
Storage and Service 11
Battery Replacement
12
Specif
Summary of the content on the page No. 2
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 2 Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty. UPS Location Warnings • Use caution when lifting your UPS. Because of the considerable weight of all rackmount UPS systems, at least two people should assist in lifti
Summary of the content on the page No. 3
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 3 Mounting (Rack) Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2-post mounting). The user must determine the fitness of hardware and procedures before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The procedures described in this manual are for common rack and rack enclosure types and may
Summary of the content on the page No. 4
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 4 Mounting (Rack) continued 2-Post (Telecom) Mounting Mount 1U UPS models in 2-post racks with user-supplied hardware following the procedure below. If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model: 2POSTRMKIT, sold separately). See Installation Kit owner’s manual for installation procedure for 2U UPS models. A Attach mounting ears to the front
Summary of the content on the page No. 5
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 5 Quick Installation 1 Unplug computer’s power cord from both AC outlet and computer’s AC input. 1 IEC320-C14 plug shown A Insert the female plug of com- 2 A puter’s cord into UPS’s AC input. Insert the male plug of computer’s cord into AC outlet.* NOTE! after you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries,** but will not supply power to its outlets until it is turned ON (see Step
Summary of the content on the page No. 6
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 6 Optional Installation These connections are optional. Your UPS will function properly without these connections. Note: SMX3000XLRT2U shown in all diagrams. 1 USB and RS-232 Serial Communications (all models) 1a Use the included USB cable (see ) and/or DB9 serial 1a 1b cable (see ) to connect the communication port on your computer to the communication port of your UPS. Install on your computer the Tripp Lite PowerAlert
Summary of the content on the page No. 7
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 7 Basic Operation Buttons (Front Panel) “POWER” Button • To turn the UPS ON: with the UPS plugged into a live AC wall outlet*, press and hold the POWER button for one second.** Release the button. If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and supply power for a limited time from its batteries***) by pressing and holding the POWER button for one second.** • To turn the UPS OFF: with the UP
Summary of the content on the page No. 8
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 8 Basic Operation continued Indicator Lights (Front Panel) All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned ON. “POWER” LED: this green LED lights continuously when the UPS is ON and supplying connected equipment with AC power from a utility source. The LED flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS is operating from its internal batteri
Summary of the content on the page No. 9
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 9 Basic Operation continued Other UPS Features (Rear Panel) AC Receptacles: Your UPS features IEC320-C13 outlets, and select models also feature IEC320-C19 outlets. These output receptacles provide your con- nected equipment with AC line power during normal operation and battery power during blackouts and brownouts. The UPS protects equipment connected to these receptacles against damaging surges and line noise. If you h
Summary of the content on the page No. 10
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 10 Basic Operation continued Accessory Slot: Remove the small cover panel from this slot to install optional accessories to remotely monitor and control your UPS. Refer to your accessory’s manual for installation instructions. Contact Tripp Lite Customer Support at (773) 869-1234 for more information, including a list of available SNMP, network management and connectivity products. Power Sensitivity Adjustment (Select Mo
Summary of the content on the page No. 11
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 11 Storage and Service Storage Before storing your UPS, turn it completely OFF: with the UPS ON and receiving utility power, press and hold the POWER button for one second (an alarm will beep once briefly after the inter- val has passed); then, unplug the UPS from the wall outlet. If you store your UPS for an extended period of time, recharge the UPS batteries once every three months: plug the UPS into a wall out- let; a
Summary of the content on the page No. 12
200309053 93-2186 SmartProInt Owner’s Manual.qxd 3/30/2004 11:42 AM Page 12 Battery Replacement Under normal conditions, the original batteries in your UPS will last many years. See Safety section before replacing batteries. The batteries are designed for hot-swap replacement (i.e. leaving the UPS in ON mode), but some users may wish to put the UPS in the OFF mode before proceeding. 1U UPS Models 2U UPS Models Procedure 1 Remove Front Panel 2 Disconnect Batteries 1 6 1 6 3 Remove/Dispose of B
Summary of the content on the page No. 13
1111 W. 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www.tripplite.com
