Furman Sound PL-8 PRO II user manual

Summary of the content on the page No. 1

pro SErIES II 20 amp powEr CondItIonErS

Summary of the content on the page No. 2

pro SErIES II 20 amp powEr CondItIonErS system, and repair of your surge suppressor. P-8 Pro S eries II Features Not so with SMP+. With Furman’s SMP+, • SMP+ with Extreme Voltage Shutdown damaging transient voltages are safely absorbed, clamped, and dissipated. No • LiFT (Linear Filtering Technology) with zero sacrificed parts, no service calls, no down time. ground contamination • Eight rear panel outlets and one front panel Unique to Furman’s SMP+ is its unparalleled outlet clampin

Summary of the content on the page No. 3

pro SErIES II 20 amp powEr CondItIonErS only. Do not use solvents or abrasive cleaners. WA R N I N G Never pour liquid on or into the unit. To reduce the risk of electrical shock, do not expose this equipment to rain or moisture. 7. Your Pro Series II unit should be serviced by Dangerous high voltages are present inside the qualified service personnel when: enclosure. Do not remove the covers. refer servicing to qualified personnel only . The • The power supply cord or the plug has bee

Summary of the content on the page No. 4

pro SErIES II 20 amp powEr CondItIonErS are so high that operation would be impossible o P E r AT I o N and shuts the power down before damage can occur. Upon initially applying power to retractable rack Lights, rear panel Lamp these units, the Extreme Voltage indicator and dimmer Control: LED will light if the input voltage is above the The PL-8 Pro II utilizes a dimmer control for extreme voltage cutoff, and power will not be the two retractable front panel light tubes. applied to t

Summary of the content on the page No. 5

pro SErIES II 20 amp powEr CondItIonErS contain can be considerable, enough to T r o U B L E S H o o T I N G G U I D E damage sensitive solid-state components in audio and computer equipment. Spikes 1.) Symptom: No power to the AC outlets. can also foul switch contacts and degrade wiring insulation. They are an unavoidable possible Cause: Circuit breaker switch has component of electric power. They are caused tripped to the off position, due to excessive unpredictably by electric m

Summary of the content on the page No. 6

pro SErIES II 20 amp powEr CondItIonErS of the product is allowed fifteen days from Furman Sound. This warranty also does not the date of purchase to complete warranty apply to Products upon which repairs have registration by mail or on-line at the Furman been affected or attempted by persons other website. If the Product does not conform to this than pursuant to written authorization by Limited Warranty during the warranty period Manufacturer. (as herein above specified), Purchaser shall

Summary of the content on the page No. 7

pro SErIES II 20 amp powEr CondItIonErS P-8 Pro rear light switch Protection oK Switched outlet Power Switch & Extreme Voltage LED’s Dimmer control for PL-8 Pro front rack lights rear light switch Protection oK Switched outlet Power Switch LED rack Lights & Extreme Voltage LED’s rear of both Analog outlets Digital outlets BNC connector for optional gooseneck light 6

Summary of the content on the page No. 8

Make sure to pick up one of Furman’s p goosneck ro SEr lights IES II 20 - the perfect amp accesory powEr CondItIonErS for your Series II unit. SpECIFICatIonS Current rating: 20 amps GN-LED Operating Voltage: 90 to 140 VAC Over Voltage Shutdown: 140 VAC typically Spike Protection Modes: GN-I Line to neutral, zero ground leakage Spike Clamping Voltage: 188 Vpk @ 3,000 amps, (133 VAC RMS) Response time: 1 nanosecond Maximum surge current: 6,500 amps Noise attenuation: 10 dB @ 10 kHz 40 dB @