Summary of the content on the page No. 1
Table of Contents
Express XR/XRT
128 kbps ISDN Modem
Quick Start Guide
1200153L1 Express XR, Data Only
1200153L2 Express XRT, Two Phone Ports
3360.9VU01 Express XR Power Supply, 9.0 V DC Output
336048VUR-2 Express XRT Power Supply, 48 V DC Output
61200.153L1-13E
September 1996
Summary of the content on the page No. 2
Table of Contents Trademarks Express XR, Express XRT, and Express Configuration Wizard are trademarks of ADTRAN, Inc. Hayes is a registered trademark of Hayes Microcomputer Products, Inc. HyperACCESS is a registered trademark of Hilgraeve Inc. MicroPhone Pro is a trademark of Software Ventures Corporation. PROCOMM PLUS is a registered trademark of Datastorm Technologies, Inc. ReachOut is a registered trademark of Stac Electronics. Windows is a registered trademark and Windows NT is a trademark o
Summary of the content on the page No. 3
Table of Contents FCC regulations require that the following information be provided to the customer in this manual. 1. If your telephone equipment (Express XR/XRT) causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC. 2. Your telephone company may make ch
Summary of the content on the page No. 4
CANADIAN EMISSIONS REQUIREMENTS This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of the Depart- ment of Communications. Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class B prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003 edictee par le ministr
Summary of the content on the page No. 5
WARRANTY: ADTRAN warrants that items manufactured by ADTRAN and supplied under Buyer’s order shall be free from defects in materials and workmanship and will conform to applicable specifications and drawings. ADTRAN’s liability herein, whether based upon breach of warranty or contract or negligence in manufacture, shall be limited to replacement or repair at ADTRAN’s election of all such defective or nonconforming items, provided that this warranty shall apply only where Buyer has given ADTRAN w
Summary of the content on the page No. 6
Table of Contents repair will be invoiced and the return of the item will be made using the most economical shipment means available. ADTRAN will use other means of express shipment at the request of the Buyer. In this case, the cost of shipping shall be paid by the Buyer. ALTERATION TO EQUIPMENT PURCHASED: Modification or alteration to purchased equipment by Buyer, other than that specifically authorized by this Agreement or by ADTRAN, shall VOID AND NULLIFY, in its entirety, all warranty condi
Summary of the content on the page No. 7
Table of Contents Telephone Company Contacts for ISDN Service Ameritech ISDN Repair 1-800-TEAMDATA Bell Atlantic 1-800-204-7332 Bell South 1-800-247-2020 Cincinnati Bell 1-513-566-1611 NYNEX 1-800-NYT-FAST (New York Area) 1-800-650-ISDN (New England Area) Pac Bell 811-8081* Rochester Tel 1-716-777-1811 Southwestern Bell 1-214-841-7799 (Dallas area) 1-800-286-8313 (Houston area) 1-800-344-6357 (Austin area) 1-314-571-2200 (St. Louis area) US West 1-800-223-7508 *all Pac Bell customers may call th
Summary of the content on the page No. 8
Table of Contents
Summary of the content on the page No. 9
Table of Contents Table of Contents Chapter 1. Introduction Express XR/XRT Overview ................................................................................... 1 Getting Started ......................................................................................................... 1 Minimum Requirements ......................................................................................... 2 What You Provide ...........................................................................
Summary of the content on the page No. 10
Table of Contents Chapter 3. Installing an Analog Modem External Analog Modem Application ................................................................. 27 Connecting an External Analog Modem..................................................... 28 Installing a New External Analog Modem ................................................. 29 Configuring an External Analog Modem ................................................... 30 Required External Analog Modem Settings ........................
Summary of the content on the page No. 11
Table of Contents Appendix D. Loop Status Messages 75 Appendix E. Connector Pinouts 77 List of Tables Table B-A Express XR/XRT LEDs .................................................................... 63 Table E-A RS-232 Interface ................................................................................ 77 Table E-B Modem Interface .............................................................................. 78 Table E-C RJ-11 POTS Port Interfaces......................................
Summary of the content on the page No. 12
Table of Contents
Summary of the content on the page No. 13
Chapter 1. Introduction Chapter 1 Introduction EXPRESS XR/XRT OVERVIEW The Express XR/XRT provides high speed network access for Internet and remote office connectivity using ISDN. The unit includes ISDN terminal adapter and network termination (NT1) functionality, eliminating the need for an external NT1 device. The Express XR™ and the Express XRT™ provide the following features: • Data rates up to 230.4 kbps - over eight times faster than analog modems • Simple setup with the Express Config
Summary of the content on the page No. 14
Chapter 1. Introduction Before getting started, review the section Minimum Requirements in this chapter to ensure your computer is compatible. In addition, examine the contents of the box to ensure everything has been received undamaged and gather the required setup information provided by your telephone company. MINIMUM REQUIREMENTS What You Provide In order to operate the Express XR/XRT the following is re- quired: • A computer (386 or higher PC, or Macintosh) • Windows 3.1 or higher for PC
Summary of the content on the page No. 15
Chapter 1. Introduction What ADTRAN Provides The ADTRAN Express XR/XRT is packaged with the following contents (see Figure 1-1): • Express XR or Express XRT • ADTRAN Express XR/XRT Quick Start Guide • ADTRAN Express Configuration Wizard software (2 disks) ® • HyperACCESS communications software (1 disk) • AC power supply • RJ-45 to RJ-11 telephone cable RJ-45 to RJ-11 telephone cable AC power supply RJ-11 RJ-45 Diskettes Express XR or XRT Quick Start Guide Figure 1-1 Express XR/XRT Contents 612
Summary of the content on the page No. 16
Chapter 1. Introduction 4 Express XR/XRT Quick Start Guide 61200.0153L1-13
Summary of the content on the page No. 17
Chapter 2. Installation Chapter 2 Installation INSTALLING THE ADTRAN EXPRESS XR/XRT This section describes how to connect the Express XR/XRT to a PC and how to install the Express Configuration Wizard soft- ware. Verify Switch Settings Dip switches 1 and 2 located on the rear panel of the Express XR/XRT allow certain settings to be physically configured. Figure 2-1 shows the location of the dip switches on the rear panel of the unit. The factory default position for all switches is down (On) du
Summary of the content on the page No. 18
Chapter 2. Installation SW 2: Off (Up) = Factory Default On (Down) = Normal (previous settings saved) If Switch 2 is set to the Off position, the unit continues to use the factory default settings until Switch 2 is set to the On position. Also, area code, phone numbers, SPIDS, and stored numbers are cleared. Express XRT Only: SW 3: Off (Up) = Phone Volume Loud On (Down) = Phone Volume Normal SW 4: Reserved for future use. OFF ON 1234 POWER RS232 ISDN OFF 1234 ON Figure 2-1 Dip Switches on Rea
Summary of the content on the page No. 19
Chapter 2. Installation 7. Plug the RJ-11 connector (small end) of the RJ-45 to RJ-11 telephone cable into the ISDN telephone wall jack. At this time the Express XR/XRT is powered on and the PWR LED should either be flashing or on solid. See the section LEDs for more information. 8. Power on the computer. 9. Go to the Express XR/XRT Software Installation procedure. COM Port Rear View of PC AC Outlet RS-232 Cable RJ-45 to RJ-11 Telephone Cable OFF ON 1234 POWER RS232 MODEM 21 ISDNU ISDN Tele
Summary of the content on the page No. 20
Chapter 2. Installation Microsoft Windows 95 and Windows NT 4.0 Windows 95 Plug and Play 1. During the Windows 95 boot process, if the New Hardware Found screen appears indicating Unknown Device, select Driver from disk provided by hardware manufacturer. If the Windows 95 New Hardware Found screen does not appear, skip the rest of this section and go to the Win 95/NT 4.0 Control Panel Modem Installation section. 2. Insert the disk labeled Windows 95 and Windows NT into the 3.5" floppy disk dri
