Summary of the content on the page No. 1
54-2101-01A.qxd 8/4/2003 1:57 PM Page 1
Pendant Speaker
Model: 700286198 / 700286206
(Black) (White)
Installation and Use Manual
Issue 1, August 2003
© 2003 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-2101-01A 0308 Printed in Taiwan.
Summary of the content on the page No. 2
54-2101-01A.qxd 8/4/2003 1:57 PM Page 2 Product Description You have purchased one of the finest pendant loudspeakers available today. Please familiarize yourself with this product by reading and reviewing the following descrip- tions and diagrams. These loudspeakers include a "spiderless" woofer that utilizes a high-gauss ferroflu- id to guide the voice coil through the magnetic field.The benefits over conventional woofers with cloth spiders are several, including the ability to constantly a
Summary of the content on the page No. 3
54-2101-01A.qxd 8/4/2003 1:57 PM Page 3 Product Diagrams Front Drawing 1.Tap Selection Switch 2. Coaxial Driver Assembly 3. Grille Retention Slot 4. Bass Tuning Vent (x2) 5. Perforated Steel Grille Front Drawing (grille partially shown) Rear Drawing 1. Snap-Lock Input Connector 2. Suspension Points (x3) 3. Safety Cable Suspension Point Package Contents Rear Drawing (1) Pendant Speaker (1) Installation and Use Manual (1) Snap-Lock Input Connector (1) Quick-Snap Clip (2) Cable Kits (3) Suspensi
Summary of the content on the page No. 4
54-2101-01A.qxd 8/4/2003 1:57 PM Page 4 Speaker Installation If the power level is known, then select it using the front-mounted selector switch prior to installing the speaker. See section Selecting Power Levels. Speaker Grille Removal Insert a pocket knife blade between the grille and the 1 bezel about a /4" deep and then gently pry the grille upwards. Do this in multiple places around the circum- ference of the grille to free the grille. Speaker Grille Installation The speaker grilles fit
Summary of the content on the page No. 5
54-2101-01A.qxd 8/4/2003 1:57 PM Page 5 Speaker Wiring Wiring is terminated at a snap-lock input con- nector. There are two positive and two nega- tive terminals to accommodate daisy chaining of speakers in a system. All wiring should be done prior to installation and then plugged into the rear of the speaker. Daisy Chaining The speaker’s snap-lock input connector allows for easy daisy chaining of speakers by providing a second terminal of each polarity. Refer to the figures for proper wiring
Summary of the content on the page No. 6
54-2101-01A.qxd 8/4/2003 1:57 PM Page 6 Selecting Power Levels The front-mounted selector switch is used to set the appropriate power level or impedance for your system. Using a small flat-blade screw- driver, turn the knob until the slot points to the power level you require. 70V/100V Systems Both power setting scales for 70V and 100V sys- tems are labeled on the speakers. On the 100V scale, the last position clockwise is marked with a (not available) symbol. Do not use this posi- tion
Summary of the content on the page No. 7
54-2101-01A.qxd 8/4/2003 1:57 PM Page 7 Specifications SPECIFICATIONS 700286198 & 700286206 * 60 Hz to 19 kHz Frequency Response (-10 dB) 1 LF Driver 6- /2" MDT Metal-Alloy Cone 3 HF Driver 20 mm ( /4") Polycarbonate Dome Sensitivity (1W/1M) 89.5 dBspl (Average 100 Hz - 10 kHz) Impedance Ratings Low (16 ohms) / High (70V/100V) Power Input (Max.) 100W @ 16 ohms; 32W @ 70V/100V 70V: 32, 16, 8, 4, 2, 1 † Power Settings (in watts) 100V: 32, 16, 8, 4, 2 Enclosure Material ABS Grille Material Powd
Summary of the content on the page No. 8
54-2101-01A.qxd 8/4/2003 1:57 PM Page 8 ©2003 Bogen Communications, Inc. Specifications are subject to change without notice. www.paging-solutions.com 1-877-852-PAGE
