Summary of the content on the page No. 1
Owner’s
Manual
MSS530 and MSS630 Loudspeaker Systems
MSS530
MSS630
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
Summary of the content on the page No. 2
Thank You Table of Contents Your decision to own this McIntosh MSS530 or MSS630 Thank You.......................................................................... 2 Loudspeaker System ranks you at the very top among dis- Please Take a Moment ....................................................... 2 criminating music listeners. You now have “The Best.” The Technical Assistance .......................................................... 2 McIntosh dedication to “Quality,” is assurance that you Cus
Summary of the content on the page No. 3
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. General: Repair of Equipment: 1. Read all the safety and operating instructions, con- 13. Refer servicing to a qualified service personnel under tained in this owner’s manual, before operating this the following conditions: equipment. A. The cords or the connectors have been damaged. 2. Retain this owner’s manual for future reference about B. Objects have fallen onto, or liquid has been safety an
Summary of the content on the page No. 4
Introduction Top View of the MN530 and MN630 The McIntosh Woofer/Midrange and Tweeter Drivers offer Crossover Networks extremely smooth frequency response, low distortion, high 2.7" sensitivity and high power handling capability. When these 6.86cm Drivers are combined with other McIntosh Vehicle Compo- nents, you will enjoy sonically accurate music reproduction in your vehicle which meets McIntosh traditional standards of excellence. Performance Features • • • • • Patented Technology ® (Lo
Summary of the content on the page No. 5
Introduction, Performance Features and Overall Dimensions Front View of the MS20 Tweeter Driver Side View of the MS20 Tweeter Driver Rear View of the MS20 Tweeter Driver 1.8" 0.88" 2.13" 4.55cm 2.24cm 5.4cm Front View Side View 2.9" of the MS530 of the MS530 7.37cm Woofer/Midrange Woofer/Midrange Driver Driver 5.4" 13.59cm Front View Side View 3.25" of the MS630 of the MS630 8.26cm Woofer/Midrange Woofer/Midrange Driver Driver 5 6.3" 15.9cm 6.1" 15.49cm 7.
Summary of the content on the page No. 6
Installation It is recommended that a qualified professional install all 5. Place the wide foam ring gasket on the back side of the McIntosh Sound System Products. McIntosh Woofer/ plastic mounting ring that will contact the vehicle Midrange Drivers, Tweeters and Crossover Networks panel or enclosure. should be used in conjunction with McIntosh Subwoofers 6. Carefully insert the Loudspeaker and mounting ring and McIntosh Electronics to achieve the best possible per- assembly into the cutout. Sec
Summary of the content on the page No. 7
Installation Mounting the Crossover When selecting a Crossover mounting location, make sure there is adequate room for ventilation (there are openings on both sides of the Cross- Mounting Screw Locations over) and for making con- nections to it. Use the sup- plied screws for mounting the Crossover to the vehicle. 1. Using the Crossover as a template, mark the two locations to drill holes in the mounting surface for the Cross- over mounting screws. Drill two holes with an appropriate size drill b
Summary of the content on the page No. 8
How to Connect a Two Way System How to Connect a Two Way System 1. Press the connector ends of the supplied Woofer/ The Black wire connects to a MINUS (-) Terminal and Midrange Red/Black cables onto the matching Woofer/ the Red wire to the (0) POSITIVE Terminal. Note: There are two additional Tweeter Positive Terminal Midrange connecting lugs. Connections (-3dB and -6dB) that allow for a reduction 2. Attach the other ends of the two Red/Black Woofer/ in High Frequency Output to match the Sound S
Summary of the content on the page No. 9
How to Connect a Three Way System How to Connect a Three Way System 1. Press the connector ends of the supplied Woofer/ The Black wire connects to a MINUS (-) Terminal and Midrange Red/Black cables onto the matching Woofer/ the Red wire to the (0) POSITIVE Terminal. Note: There are two additional Tweeter Positive Terminal Midrange connecting lugs. Connections (-3dB and -6dB) that allow for a reduction 2. Attach the other ends of the two Red/Black Woofer/ in High Frequency Output to match the Sou
Summary of the content on the page No. 10
Specifications MSS530 System Specifications MSS630 System Specifications System Parameters System Parameters Peak Power 120 Watts Peak Power 120 Watts Continuous Power (EIA + H.P.) 60 Watts Continuous Power (EIA + H.P.) 60 Watts Frequency Response 80 Hz - 20kHz Frequency Response 80 Hz - 20kHz 1 1 System Sensitivity 85 dB System Sensitivity 85 dB Nominal Impedance (Znom) 4 Ohms Nominal Impedance (Znom) 4 Ohms Crossover Frequency 2400 Hz Crossover Frequency 2500 Hz Low Pass Slope 12 db/oct Low Pa
Summary of the content on the page No. 11
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a ship- ping carton or any of the interior part(s) are needed, please call or write Customer Service Repair Department of McIn- tosh Laboratory. 11
Summary of the content on the page No. 12
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No. 040826
