Summary of the content on the page No. 1
Colour Video Camera
AW-F575E
Electric Industrial Co., Ltd.
PO Box 288. Osaka 530-8691, J a p a n
Summary of the content on the page No. 2
6. Auto White/Auto Black Set Switch CAMERA HEAD AW-F575HE MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS (AUTO W/B BAL AWC/HOLD/ABC) This switch sets the white balance and black balance 1. Lens Connector (12-pin) (LENS) automatically as follows Connect the lens cable to this connector AWC: This position is used for setting the white bal- ance when the White Balance Selection Switch (28) is set to the AWC A or AWC B position 2. Viewfinder Connector (12-pin) (VIEWFINDER) White balance adjustment is
Summary of the content on the page No. 3
12. Back Light Compensation Switch 19. User Set Switch (USER SET 1, 2, OFF) 10. Scene File Selection Switch At the normal (NOR) position, the lens is operating (BACK LIGHT COMP ON/OFF) By setting this switch to the position 1, a Menu select- (SCENE FILE, USER A/B/1/2/3) with normal lens iris openings When backlight affects the picture, turn on this switch ed by the Scene File Switch is displayed in the This switch is used to select the most suitable camera for a clear picture. Notes: viewfinder
Summary of the content on the page No. 4
35. Viewfinder Height Adjustment Knob (UP/DOWN) 37. Remote Control Box Connector (RCB) 29. High Gain Selectlon Switch (GAIN LOW/MID/HIGH) 23. Total pedestal Level Control (T. PED) The height ot the viewfinder can be adjusted by first This connector is provided tor the Remote Control Box This switch is used to select the gain level. This control is used tor adjusting the pedestal level of The gain level can be set in the Sub Menu with the loosening this knob, adjusting the viewfinder to the (RCB)
Summary of the content on the page No. 5
-59. VTR Video Output Selection Switch 2 (SELECT 2) 46. Earphone Jack (M3) (EARPHONE) 54. Power Selection Switch (POWER SELECT. BATT/ When an earphone is connected, the sound picked up EXT DC-VTR/RCU) When the VTR Video Output Selectlon Switch 1 is set to the SELECT 2 Position, this switch should be set through the microphone or played back audio from a By using this switch the desired power source con- 3/4" U-vision recorder. 26-pin MII format portable VTR nected to the camera can be selected
Summary of the content on the page No. 6
CAMERA ADAPTOR AW-AD700BSE 75. Gen-lock Input Connector (ENC) (GEN-LOCK) Y/C/B: The chrominance (C) and luminance (Y) sig- The colour video signal of the camera is automatically nals are supplied from the R, G and B Output Connectors for S-VHS format VTR. synchronized to the gen-lock signal (composite or black burst) whtch is supplied to this connector. The R/G/B: The R. G and B stgnals are supplled from the gen-lock signal is used for system reference, such as R. G and B Output Connectors. Y/PB
Summary of the content on the page No. 7
recorded. The Tally indicator also lights when the 86. Lens Cable with 12-pin Connector After having set the recorder to the recording standby ?? 26 pin Studio Cable (RCU Cable) camera is in full system operation together with the This cable supplies power to the servo control zoom mode, press this button to start and pause recording. WV-CA26U15 Remote Control Unit and Special Effects Generator in motor and the automatlc iris control device. While recording is in progress, the Recording/T
Summary of the content on the page No. 8
REMOTE CONTROL UNIT WV-RC7OOA 1.5” ELECTRONIC VIEWFINDER WV-VF42 101. Tally Light This light is lit when the Tally ON/OFF switch (105) is set to ON position and the VTR has been set to the recording mode with the VTR Start/Stop Switch. This light indicates that recording in in progress. 102. Accesory Shoe DO not mount a light source 103. Eye Cap The eye cap, besides blocking out stray light, offers comfortable viewing of the monitor picture. The cap may be flipped open if thls is desired. 1
Summary of the content on the page No. 9
~ 117. Remote Control Box (RCB) Operation Switch turn the controls clockwise to increase the red and blue signal levels and counterclockwise to decrease Note: The smear may be appeared with the high light (RCB) these levels. objects When connecting the Remote Control Box to the cam- Note: As these controls employ Digital Processing, 133. Down switch (DOWN) era without using the Remote Control Box, set this the Red and Blue signal levels will be changed in used to choosa eslred This swi
Summary of the content on the page No. 10
149. Tally and Intercom lnput Connector 157. Remote Control Unit Connector 162. Audio Output Jack (AUDI0 OUT) Note: When using the Remote Control Box (RCB) in (TALLY & INTERCOM) This connector is used for directly connecting with the By setting the Audio Level Selection Switch of the the Remote Control Unit (RCU), the recording Connect a 4-pin cable between this connector and the Remote Control Box Connector (159) on the Remote Camera Adaptor AW-AD700BSE to the -20 dB posi- start/stop function i
Summary of the content on the page No. 11
177. Detail Level Selection Switch When this switch is set to the ATW position, white bal- REMOTE CONTROL UNIT WV-RC550 (DTL, LEVEL-HIGH/LOW/OFF) ance can be continuously adjusted automatically The detail/aperture level can be selected by this 181. Red and Blue Gain Controls (R GAIN/B GAIN) switch in three steps. Set this switch to the desired These controls are used to manually adjust the fine position while observing the sharpness of the picture level of white balance. 178. Auto White/Auto Bla
Summary of the content on the page No. 12
192. User Set Switch ( OFF / 1 / 2 ) 185. Electronic Shutter Selection Switch 200. Intercom Jack (INTERCOM) 203. Gen-lock Connectors This switch selects Encoder output or EVF (black and This jack is used for communications between the ( O F F / 120 / 500 / 1000 / S S / E L C) (GEN-LOCK IN/OUT/AUTO 75 Ohm. - Hi Z) white) output from the Video Output Connector and This switch is operative only when a camera featuring camera operator and the Remote Control unit oper
Summary of the content on the page No. 13
LENS CONTROL KIT WV-LK35 5” ELECTRONIC VIEWFINDER WV-VF65B 211. Tally Light 215. Peaking On/Off Switch (PEAKING ON/OFF) Normally this switch should be set to the OFF position This light only works when the camera is “sed in full 221. Clamper 224. VTR Start/Stop Button system operation with the Remote Control Unit (RCU) However, when shooting under low light conditions, Install the zoom controller on the right tripod arm by This button is used to start or pause the VTR Press setting this switch
Summary of the content on the page No. 14
TRIPOD MOUNTING ADAPTOR WV-QT700 LENS CONTROL KIT WV-LK36 241. Release Button The Lock Levar (242) can be unlocked by presslng this button 242. Lock Lever The mounting or removing of the camera from the Tripod Mounting Adaptor WV-OT700 is made by lock- ing or unlocking this lever. 243. Mountlng Holes These holes are used to mount the Tripod Mounting Adaptor on the tripod. CARRYING CASE WV-CC500A 251. Cushion 1 (for AW-AD500AE) Thls cushion is used to contaln the ENG configuration conflguratlon o
Summary of the content on the page No. 15
3. Installatìon of the Optional Mìcrophone Holder INSTALLATION 3-1 Remove the Microphone Fixing Screw on the MlcrophOne Of this camera. 1. Mounting the Camera Adaptor 1-1 Mount the Camera Adaptor on me Camera Head while engaging the 68-pin connector ~onnector.1 3-2 Disconnect the Microphone Connector (3-pin) of this this Microphone from the Camera. 1-2 Tighten the two Camera Adaptor Holding Screw/ Knobs flrmly, and make sure the Camera Adaptor is Note: Do not pull the Microphone Connector of t
Summary of the content on the page No. 16
6. Mounting of the MII Format VTR AU-45H/DVC 4. Mounting the 1.5" Electronic Viewfinder dockable VTR AJ-D90 4-1 Unlock the Viewfinder Lock Lever (32) on the 6-1 Remove four screws holdlng the cover for the batlery Viewfinder. connectors and remove the cover 4-2 While pulling the Viewfinder Slide Stopper, remove the Viewfinder Mountlng Base (33) by sliding it out from me Viewfinder. 4-3 Remove the screw from the Viewfinder Mounting Base 4-4 Install the Viewfinder Mountlng Base (33) into the Viewf
Summary of the content on the page No. 17
7. Mounting of the Betacam Format VTR 8. Installation of the AC Adaptor/Charger 7-1 Mounting the optional VTR Adaptor WV-VT16A WV-PS34 Mount the VTR Adaptor by connectlng the 68-pin con- When the AC Adaptor/Charger, WV-PS34, is used nector on the camera and the VTR Adaptor, and with the ENG/EFP Colour Camera as an AC Adaptor, engage the lock mechanism of the VTR Adaptor and this installation procedure should be followed: the camera head. Then tighten two VTR Adaptor 8-1 lnstall the AC Adaptor/Ch
Summary of the content on the page No. 18
10-4 Turn the Lock Lever (242) of the Tripod Mounting 9. Removing the VTR from the Camera Make Adaptor clockwise, as shown in the illustration. 9-1 Loosen two VTR Mounting Screws on the VTR sure the camera is securely held and that it is in its Handle. back-most position in the adaptor 9-2 While pressing up on the VTR Release Button, remove the VTR from the camera 10. Mounting on the Tripod Mounting Adaptor 10-1 Mount the Tripod Mounting Adaptor on the trlpod by matchlng one of the mounting h
Summary of the content on the page No. 19
Notes: B. Gen-lock EFP Application SYSTEM CONNECTION 1 The Subcarrier Phase Coarse and Subcarrier Phase Flne as well as the Horzontal Phase on the CAUTION: Keep the power switches of all units in the OFF camera should be set to match the other cameras 1 Connect a coaxial cable for the gen-lock signal in the system Refer to page 49 for details position during connections. between the Gen-lock Input Connector (51) (BNC- 2. Refer lo the operatlng nstructlons accompanylng type) on the Camera Adaptor
Summary of the content on the page No. 20
E. Gen-lock Studio Application C. Studio Application 2 Connection with the Remote Control Unit by the coaxi- - Connect a coaxlal cable for the gen-lock signal between the black burst output on the productlon system and Gen-lock input 1 Connection with the Remote Control Unlt by the 26-pin Connectors (143) or (203) on the RCU. (The signal may be bridged or looped through to another RCU.) al cable multi-cable - Connect the coaxial cable for the lineview signal between the effect output connector o
