Summary of the content on the page No. 1
COMPACT VHS CAMCORDER
VIDEOCAMARA VHS COMPACTO
CÂMERA VHS COMPACTA
GR-AXM88UM
Compact VHS
VICTOR COMPANY OF JAPAN, LIMITED
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRUÇÕES
Printed in Japan
UM
COPYRIGHT© 1997 VICTOR COMPANY OF JAPAN, LTD. 0697TOV UN YP LYT0002-0L5A
* *
PORTUGUÊS ESPAÑOL ENGLISH
GR-AXM88UM
Summary of the content on the page No. 2
2 EN Dear Customer, Warning on lithium battery Thank you for purchasing the JVC Compact The battery used in this device may present a VHS camcorder. Before use, please read the fire or chemical burn hazard if mistreated. Do safety information and precautions contained not recharge, disassemble, heat above 100°C in the following pages to ensure safe use of or incinerate. your new camcorder. Replace battery with Panasonic (Matsushita Electric), Sanyo or Maxell CR2025; use of another battery may pr
Summary of the content on the page No. 3
EN 3 IMPORTANT PRODUCT ANTENNA INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS 1. Outdoor Antenna Grounding Electrical energy can perform many useful func- If an outside antenna or cable system is connected tions. But improper use can result in potential to the product, be sure the antenna or cable system electrical shock or fire hazards. This product has is grounded so as to provide some protection been engineered and against voltage surges and built-up static charges. manufactured to assure your
Summary of the content on the page No. 4
4 EN USE SERVICING 1. Accessories 1. Servicing To avoid personal injury: If your product is not operating correctly or exhibits • Do not place this product on an unstable cart, a marked change in performance and you are stand, tripod, bracket or table. It may fall, causing unable to restore normal operation by following the serious injury to a child or adult, and serious detailed procedure in its operating instructions, do damage to the product. not attempt to service it yourself as opening or •
Summary of the content on the page No. 5
QUICK OPERATION GUIDE EN 5 SUPPLY POWER INSERTING A VIDEO CASSETTE Hook on. EJECT 1 2 Push in. 3 2 4 BATT. RELEASE PUSH 1 MONITOR OPEN Using the battery pack 1 Hook-on the battery pack's top end to the 1 Slide MONITOR OPEN to open the LCD camcorder. (Charging procedure, Z pg. 8) monitor. 2 Push in the battery pack until it locks into • Open to an angle of over 45 degrees. place. 2 Press EJECT to open the cassette holder. 3 Insert a video cassette. To remove the battery pack 4 Press PUSH to clos
Summary of the content on the page No. 6
MAJOR FEATURES 6 EN REMEMBER Integrated Auto Light (Z pg. 19) The Logical Choice Picture Stabilizer (Z pg. 24) The only compact video cassettes that can be used with your VHS VCR* Digital Hyper Zoom (Z pg. 18) Program AE with Special Zoom-in Effects (Z pg. 20) n Auto Mode Lock n Auto Mode Release n Electronic Fog Filter n ND Effect n Sepia n Twilight n Sports n 1/1000 sec. High Speed Shutter Zoom-out n 1/2000 sec. High Speed Shutter Random Assemble Editing LCD Color Monitor (Z pg. 16) (Z pg.
Summary of the content on the page No. 7
CONTENTS EN 7 GETTING STARTED 8 Power ...............................................................................................8 Clock (Lithium) Battery Insertion/Removal................................................. 10 Viewfinder Adjustment ........................................................................ 10 Date/Time Setting ............................................................................. 11 Tape Length Setting ......................................................
Summary of the content on the page No. 8
GETTING STARTED 8 EN Power CHG. (charge) indicator This camcorder’s 3-way power supply system lets you Marks choose the most appropriate source of power. POWER To AC outlet NOTES: indicator c No function is available without power supply. c Use only specified power supply. END c Do not use provided power supply units with other indicator equipment. CHARGING THE BATTERY PACK SUPPLY POWER Connect the charger’s AC power cord to a wall 1 outlet. The power indicator lights. REFRESH switch REFRESH ind
Summary of the content on the page No. 9
EN 9 **CHARGE MARKER A charge marker is provided on the battery pack to Charge marker help you remember whether it has been charged or not. Two colors are provided (red and black)—you choose which one means charged and which means discharged. NOTES: c The recording time per charge is affected by such factors as the time spent in Record/Standby mode and the frequency of zooming. It is safer to have spare battery packs. c Charging times noted on page 8 are for fully discharged battey pack, and dis
Summary of the content on the page No. 10
GETTING STARTED (cont.) 10 EN Clock (Lithium) Battery Insertion/Removal This battery is necessary for clock operation and to perform date/time settings. A SWITCH OFF POWER Switch off the unit’s power and remove the power 1 supply unit. OPEN COVER Open the clock battery compartment cover while 2 pressing the release tab. REMOVE BATTERY (when replacing) Insert a pointed, non-metallic object between the 3 battery and the compartment ( A ) and pull the battery out. INSERT BATTERY Ensuring the plus
Summary of the content on the page No. 11
EN 11 Date/Time Setting NEAR SELECT MODE First set the power switch to “CAMERA”. Turn the 1 PROGRAM AE select dial to any position except AUTO LOCK. ACCESS MENU SCREEN Press MENU. MENU FAR 2 SELECT FUNCTION Press – to move the highlight bar down to “Date/ 3 Time”, then press NEAR. The Set Date And Time screen appears. SET DATE/TIME Press FAR or NEAR until the item you want to set 4 begins blinking, then press + or – to until the correct setting appears. •If you decide you want to return the date
Summary of the content on the page No. 12
GETTING STARTED (cont.) 12 EN Tape Length Setting T20•30•40 tape length select button Set the tape length according to the length of the tape used. SET TAPE LENGTH SP-EP recording Press T20•30•40 until the required indication mode button 1 appears in the LCD monitor or the veiwfinder. T20 = 20 minutes of recording time, T30 = 30 minutes, and T40 = 40 minutes (in SP). NOTE: The tape remaining time (Z pg. 15) displayed in the LCD monitor or the viewfinder is correct only if the correct tape lengt
Summary of the content on the page No. 13
EN 13 Loading/Unloading A Cassette OPEN LCD MONITOR Slide MONITOR OPEN and open the LCD monitor 2 2 1 to an angle of over 45 degrees. 4 4 OPEN CASSETTE HOLDER Press EJECT until the holder opens. Do not use force 3 3 2 to open. 1 5 INSERT/REMOVE CASSETTE 1 Make sure the label is facing outward. 3 CLOSE CASSETTE HOLDER Press PUSH and make sure the holder is closed and 4 locked. CLOSE LCD MONITOR Turn to take First make sure the holder is closed. Then close the up slack. 5 LCD monitor. Erase Protec
Summary of the content on the page No. 14
GETTING STARTED (cont.) 14 EN Grip Adjustment EXPAND LOOP Separate the Velcro strip. 1 INSERT HAND Pass your right hand through the loop and grasp the 2 grip. ADJUST STRAP LENGTH Adjust so your thumb and fingers can easily operate 3 the Recording Start/Stop button and Power Zoom lever. Refasten the Velcro strip. Recording Start/Stop button Shoulder Strap Attachment ATTACH STRAP Following the illustration at left, thread the strap 1 through the top of the eyelet 1, then fold it back 1 and thread
Summary of the content on the page No. 15
RECORDING Basic Recording EN 15 NOTE: Tape remaining time indicator You should already have performed the procedures listed 25min below. If not, do so before continuing. *- - -min
c Power (Z pg. 8) (Now calculating) c Tape Length/Recording Mode Setting (Z pg. 12) c Grip Adjustment (Z pg. 14) 120min LOAD A CASSETTE 119min First slide MONITOR OPEN and open the LCD monitor to an angle of over 45 degrees. 1 Press EJECT to open the cassette holder, then insert Power indicator 3min the cassette wit
Summary of the content on the page No. 16
RECORDING Basic Recording (cont.) 16 EN Shooting while watching the LCD monitor Before the following steps, perform step 1 (Z pg. 15). ENTER RECORD–STANDBY MODE LENS COVER Make sure the LCD monitor is fully open. Slide the Switch 2 LENS COVER open/close switch to open the lens cover, then set the power switch to CAMERA. •The power indicator lights and the camcorder enters the Record–Standby mode. POWER •The scene you’re aimed at appears in the LCD monitor, with the word “PAUSE” superimposed Sta
Summary of the content on the page No. 17
EN 17 Journalistic shooting In some situations different angles of shooting may be required for more dramatic results. OPEN LCD MONITOR Make sure the LCD monitor is fully open. 1 TILT LCD MONITOR Tilt the LCD monitor in the most convenient 2 direction. •The LCD monitor can rotate almost full circle (270°: 90° downward, 180° upward). Self-recording You can shoot yourself while viewing your own image in the LCD monitor. TILT LCD MONITOR UPWARD Open the LCD monitor and tilt it upward to 180 1 degre
Summary of the content on the page No. 18
RECORDING Basic Features 18 EN FEATURE: Zooming PURPOSE: To produce the zoom in/out effect, or Zoom-in an instantaneous change in image magnification. OPERATION: 36X Hyper zoom Digital circuitry doubles the maximum 18x magnification offered by optical zoom. Zoom-out 1) To zoom in, slide the Zoom Lever toward “T”. 2) To zoom out, slide toward “W”. NOTES: c During Hyper Zoom, the speed increases the further you slide the Zoom indicator Zoom Lever. bar c Focusing may become unstable during Hyper Z
Summary of the content on the page No. 19
EN 19 Video Light When natural lighting is too dim, you can brighten the scene by using the built-in video light. SET VIDEO LIGHT Set the LIGHT OFF/AUTO/ON as required. 1 ON : Always keeps the light on as long as the camcorder is turned on. AUTO : Automatically turns on the light when the camcorder senses insufficient lighting on the subject. OFF : Turns off the light. LIGHT OFF/AUTO/ON •The video light can be used with the camcorder’s power on. •It is recommended to set the white balance (Z pg.
Summary of the content on the page No. 20
D N G F E E S A D E O L M E R O T K RECORDING Advanced Features 20 EN Program AE With Special Effects 1 second later, the mode is activated. All you have to do to access any of the variety of After 1 sec. shooting effects is to turn the PROGRAM AE select dial. Sepia SELECT MODE Turn the PROGRAM AE select dial until the symbol 1 of the function you want is aligned with the mark. LCD monitor or •The selected mode’s name and its indication are viewfinder displayed in the LCD monitor or the viewfin
