Carrier SYSTEM PILOT 33PILOT-01 user manual

Summary of the content on the page No. 1

System Pilot
Owner’s Manual
Part Number 33PILOT-01
System Pilot reads that device’s first status table and displays it
CONTENTS
as the Default screen.
Page
→ DEFAULT DEVICE DESIGNATION — If the System Pi-
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
lot is connected to a local bus of a VVT® zone controller
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(Comm2), the default device is the local zone controller. If the
OPERATION. . .

Summary of the content on the page No. 2

MODIFY/ NAVIGATE/ EXIT SELECT Fig. 2 — Zone Controller Default Screen + PAGE SCROLL - Fig. 5 — System Pilot User Interface items currently on the screen with the previous or next 7 items from the table or list. Fig. 3 — Bypass Controller Default Screen If there is

Summary of the content on the page No. 3

→ MODIFY — Like the INC/DEC buttons, this rotary knob modi- Program Mode — To enter Program mode and display fies the value of the highlighted field within its defined limits. The the Program screen, press the SCROLL UP and SCROLL value increases or decreases with each increment of the rotary DOWN buttons together for 3 seconds from the default screen. knob. Turning the knob clockwise increases the value. Turning it The System Pilot will display one of the three program screens counterclockwise

Summary of the content on the page No. 4

Ctrl-ID Ctrl-ID Ctrl-ID CONFIG SETPOINTS ALARM HIST SETPOINTS ALARM HIST ATTACH SCHEDULES ATTACH DETACH ALARM HIST DETACH ATTACH DETACH Ctrl-ID → Fig. 6 — Program Screens → CTLR-ID — Selecting the Ctlr-ID option from the Program screen displays the Controller ID screen shown in Fig. 9. The center portion of the screen shows the following infor- matio

Summary of the content on the page No. 5

→ CONFIG AND SETPOINT TABLES — If the CONFIG or If the EXIT button is pressed, the System Pilot exits to the SETPOINTS table option is selected from the Program screen, next higher screen. and if there is more than one entry in the corresponding table SCHEDULE — Selecting the SCHEDULE option from the list, then the System Pilot displays a Table List screen. If there Program screen and then selecting a Time Schedule table is only a single table, the System Pilot displays the contents of displays

Summary of the content on the page No. 6

the set points if the set point units are degrees, otherwise, they will be ignored. The System Pilot's internal limits will not affect the display. The System Pilot reads the set points from the device and displays them as read, even if they are outside the configured System Pilot limits. Pressing SELECT while a set point is blinking sends the new set point to the controller. Before sending the new set point to the device, the System Pilot will clamp the set point to its own internal limits and

Summary of the content on the page No. 7

START MONTH — Use this decision to indicate the month of the year in which the holiday will begin. Start Month: Allowable Entries 1 to 12 Default Value 1 START DAY — Use this decision to indicate the day of the month on which the holiday will begin. Start Day: Allowable Entries 1 to 31 Default Value 1 DURATION — Use this decision to indicate the number of consecutive days that the holiday will last. If you enter 0 in this decision, the hol

Summary of the content on the page No. 8

Copyright 2004 Carrier Corporation Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book 1 4 PC 111 Catalog No. 533-30017 Printed in U.S.A. Form 33ZC-4SO Pg 8 606 10-04 Replaces: New Tab 11a 13a