Kohler Karbon Kitchen Sink Tap K-6227A user manual

Summary of the content on the page No. 1

K-6227A
Karbon™ Kitchen Sink Tap
Installation and User Guide
IMPORTANT
INSTALLER: This product manual is the property of the customer and must
be retained with the product for maintenance and operational
purposes.
1109784-A2-A
1

Summary of the content on the page No. 2

IMPORTANT INORMA f TION Due to the non-standard diameter of the remote valve (51 mm), the remote valve cannot be installed through a standard 35 mm tap hole in a sink. Choose a sink without tap holes then install the tap and remote valve through the countertop. Refer to the countertop manufacturer for drilling of the holes. Tap 1. Make sure that you follow all the local plumbing and building regulations in operation. 2. For new installations, install the tap in the sink before install

Summary of the content on the page No. 3

INSTAllATION 1. Locate the remote valve within Valve Hole 203 mm of the spout. Refer to the countertop manufacturer for drilling of the holes. Ø 51 mm Ø 35 mm 203 mm Max Spout Hole 2. Apply silicone sealant to the underside of the concealing plate. Concealing Plate 1109784-A2-A 3

Summary of the content on the page No. 4

3. Insert the tap through the mounting hole. 4. Partially thread the screws into the ring. 1109784-A2-A 4

Summary of the content on the page No. 5

5. Fit the fibre and metal washers onto the threaded shank Install the ring leaving approximately 6 mm between the ring and the Fibre Washer countertop. 6 mm Ring Metal Washer 6. Turn the ring until the screws are to the front and the back. Tighten the screws securely and evenly. 1109784-A2-A 5

Summary of the content on the page No. 6

7. Apply silicone sealant to the underside Remote Valve of the remote valve. Install the remote valve through the hole in the countertop. Hot Cold On 8. Before tightening the remote valve, make sure that the cold water supply is on the left hand side. 9. Partially thread the screws into the ring. 1109784-A2-A 6

Summary of the content on the page No. 7

Countertop 10. Slide the washer onto the remote valve threaded shank. Install the ring leaving approximately 6 mm between the ring and the countertop. Washer Ring 6 mm Ring 11. Turn the ring until the screws are to the front and the back. Tighten the screws securely and evenly. 1109784-A2-A 7

Summary of the content on the page No. 8

12. Connect the inlet hose to the spout Spout Connection connection. Inlet Hose 13. Connect and tighten the supply hoses. Note! If the sink installation requires that you coil the supply hoses, maintain a 76 mm diameter inside the coil. Ø 76 mm Min Cold Hot 14. Check for leaks. 1109784-A2-A 8

Summary of the content on the page No. 9

15. Remove the aerator. Key 16. Flush the lines. 17. Reinstall the aerator. Key 1109784-A2-A 9

Summary of the content on the page No. 10

SPARe PARTS 1088909 1071700** 1090946** Setscrew Handle Spout 1088909 1054201 Setscrew 1054197** Spring Ball Joint 1088910 1071701 O-Ring Friction Cup 1071702** 1090945** Disk Tube 1071704** 1071689** 1090943 1071703 Concealing Plate 1021051 Tube Spring Bearing Check Valve 42043 O-Ring 1095310 1088910 Check Valve 1090949** 1018336** O-Ring Base Mounting Nut 1090948 Valve 1090944 Adapter 1109796 1031961 Valve Body Shank w/Hoses 1090942 1090941 77950 Aerator Sprayhead O-Ring 22352 Washer 1071706 W

Summary of the content on the page No. 11

dIMeNSIONS 52 mm 337 mm Max 102 mm 203 mm Max 227 mm 176 mm 110 mm Ø 67 mm Ø 67 mm 64 mm 64 mm 2" 1-1/4" Max 590 mm All dimensions in mm 1109784-A2-A 11

Summary of the content on the page No. 12

CARe ANd CleANINg Like anything of lasting quality , Kohle r tapware and fittings require a certain amount of periodic care to p r e s e r v e t h e i r l u s t r o u s fi n i s h . C l e a n y o u r n e w K o h l e r t a p w a r e a n d fi t t i n g s w i t h a m i l d s o a p , r i n s e t h o r o u g h l y with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any water from metal surfaces. Allowi