Hans Grohe ShowerArc 26396001 user manual

Summary of the content on the page No. 1

Installation Instructions / Warranty
ShowerArc
26396001

Summary of the content on the page No. 2

ShowerArc 26396001 Minimum ceiling height – 90 1/2” 2

Summary of the content on the page No. 3

Installation Considerations • For best results, Hansgrohe recommends on the left and the cold supply must enter that this unit be installed by a licensed, the valve on the right. If the valve is cross- professional plumber. connected, it cannot function correctly. • Please read over these instructions thor- • The difference in water pressure between oughly before beginning installation. the hot and cold supplies should not Make sure that you have all tools and sup- exceed 10 psi or the the

Summary of the content on the page No. 4

Installation in 90º corner: Instructions begin on page 5 Wall-to-wall installation Requires 26397000 installation kit (included): Instructions begin on page 13. Roughing-in The ShowerArc requires 1/2” NPT female fittings, recessed 3/8” behind the surface of the finished wall, for the hot and cold water supplies for the thermostatic mixing valve. 4

Summary of the content on the page No. 5

Installation in 90º corner Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. This diagram shows both possible positions for the installation. 5

Summary of the content on the page No. 6

Installation in 90º Corner Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 6

Summary of the content on the page No. 7

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 7

Summary of the content on the page No. 8

9 10 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 11 Be careful not to drill into water lines! 12 6 mm 8

Summary of the content on the page No. 9

13 14 15 16 9

Summary of the content on the page No. 10

17 18 19 20 1 2 6 mm 10

Summary of the content on the page No. 11

21 22 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 24 23 2 1 6 mm 11

Summary of the content on the page No. 12

25 26 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Turn to page 22 to continue the installation. 12

Summary of the content on the page No. 13

Wall-to-Wall Installation Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. The diagram shows both possible positions for the installation. 13

Summary of the content on the page No. 14

Wall-to-Wall Installation Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 14

Summary of the content on the page No. 15

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 15

Summary of the content on the page No. 16

9 10 11 12 2 Seal the wall around the anchors with waterproof 6 mm sealant. Failure to seal the wall can lead to possible water damage. 1 Be careful not to drill into water lines! 16

Summary of the content on the page No. 17

13 14 Install the 26397000 mounting set 15 16 17

Summary of the content on the page No. 18

17 18 90 20 19 XX = XX 18

Summary of the content on the page No. 19

21 22 1 2 6 mm 23 24 M6x8 SW 3 mm 19

Summary of the content on the page No. 20

25 26 2. M6x8 1. 3. SW 3 mm M6x60 Install the 26397000 mounting set 27 28 2 Seal the wall around the an- 1 chors with waterproof sealant. 6 mm Failure to seal the wall can lead to possible water damage. 20