Summary of the content on the page No. 1
SELECTRONIC®
Hard-Wired AC Powered Moments
Lavatory Proximity Faucet
PRODUCT NUMBERS
2506.192, 2506.195
Product No.'s & Options 1
Specifications 2
How to Install 2-3
Electrical Hook-up 4-5
Maintenance 6-7
FAQ,s 8
Replacement Parts 9
Certified to comply with ASME A112.18.1M
© 2007 American Standard
M965274
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at
Summary of the content on the page No. 2
Base P r oduct Mixing Valve Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. UNPACKING Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they h
Summary of the content on the page No. 3
Fig. 1 Roughing-in Dimensions FINISHED GENERAL DESCRIPTION: WALL 154mm Electronic faucet with proximity operation. Vandal (6-1/16) resistant solid brass construction single post 126mm 159mm (5) mounting. Operates on AC permanent power. Water (6-1/4) pressure range from 20 to 125 psi. In-line strainer 55.5mm (2-3/16) for solenoid is integral. Single inlet 3/8 compression, built-in checks, and flexible stainless steel 15" reach 49mm 32mm (1-1/4) inlet hose for spout connection. (2) Note: All
Summary of the content on the page No. 4
MOUNT ENCL 2 OSURE; Fig. 2 Fig. 2 LAVATORY RIM OR MOUNTING SURFACE 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical 14" (356mm) connections from the spout assembly to be made. ENCLOSURE NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance MOUNTING SUPPLIES 1 HOLES between wall supply and ENCLOSURE (1) must be 2-3/4" taken into consideration. (71mm) WASTE 2. Remove 4 screws from COVER (2) and p
Summary of the content on the page No. 5
Fig. 1 4 1 ELECTRICAL INSTALLATION 5 1 ELECTRICAL CONNECTIONS; Fig. 1 Before opening ENCLOSURE CAUTION disconnect AC power supply. 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Feed the WIRE CONNECTORS (2) through the top of ENCLOSURE (5). Fig. 1a. 3. Remove GROMMET (4) from ENCLOSURE (5). Fig. 1. Fig. 1a Fig. 1b 4" 4. Feed the gray SENSOR WIRE (7) through GROMMET (4), 4" from CONNECTOR. Fig. 1b. Insert gray SENSOR WIRE (7) into SPLIT PLUG (9). Push 5 SPLIT PLUG (9) into GROMMET (4) to se
Summary of the content on the page No. 6
Fig. 2 Unit #1 Unit #2 Unit #3 10 9 4 4 T TW WO PIECE O PIECE GR GROMMET OMMET 6 3 3 1 3 2 1 4" 1 1 1 5 FOR AC-VERSION 2 Fig. 3a (MULTI HOOK-UP); Fig. 2, 3 T TW WO O PIECE PIECE 1. See AC Version Electrical Hook-up for first unit of the G GR ROMMET OMMET 8 Multi hook-up. 7 2. Remove ENCLOSURE COVERS from all ENCLOSURES. 3. Remove SOLID BLACK INSERT(1) from right side of ENCLOSURE #1 and replace with gray 2-PIECE GROMMET (3).
Summary of the content on the page No. 7
Fig 1 MAINTENANCE H 1 AND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone. Detection Zon
Summary of the content on the page No. 8
4 HOW TO CLEAN FILTER; Fig. 4 Fig.4 Before opening ENCLOSURE CAUTION disconnect AC power supply. 1. Remove ENCLOSURE COVER. 2. Close SUPPLY STOP (5) with 4mm Hex wrench. 3 Note: Keep water flowing out of faucet while shutting off. 4 3. Pull off Red (1) and Black (2) CONNECTORS from SOLENOID VALVE (3). CLEAN SCREENS 4. Unthread STRAINER (4) using a 7/16" socket. 5. Pull out the STRAINER (4) and clean with an old toothbrush. Rinse thoroughly with water. 6. Install the STRAINER (4) back in i
Summary of the content on the page No. 9
FAQ'S Q: How will I know if battery needs to be replaced? Q: Why does the faucet operate the opposite of A: Valve does not open and sensor blinks 2 times expected-Turns On when not in sensor range, but turns interrupted by pause for up to 7 days. off when in sensor range? A: Sensor wires to solenoid are reversed. Black to - Q: Why has the flow rate of the faucet reduced & Red to + is correct. significantly? A: Check and clean aerator and strainer. Q: What is the normal operating pressur
