Summary of the content on the page No. 1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
Power Planer
KP0810
KP0810C
007638
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1
Summary of the content on the page No. 2
ENGLISH (Original instructions) SPECIFICATIONS Model KP0810 KP0810C Planing width 82 mm Planing depth 4 mm Shiplapping depth 25 mm -1 No load speed (min) 16,000 12,000 Overall length 290 mm Net weight 3.3 kg 3.4 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003 END201-5 Uncertainty (K) :
Summary of the content on the page No. 3
• Be sure to identify safety measures to protect the Work area safety operator that are based on an estimation of 1. Keep work area clean and well lit. Cluttered or exposure in the actual conditions of use (taking dark areas invite accidents. account of all parts of the operating cycle such as 2. Do not operate power tools in explosive the times when the tool is switched off and when it atmospheres, such as in the presence of is running idle in addition to the trigger time). flammable liqui
Summary of the content on the page No. 4
up or carrying the tool. Carrying power tools Service with your finger on the switch or energising power 25. Have your power tool serviced by a qualified tools that have the switch on invites accidents. repair person using only identical replacement 14. Remove any adjusting key or wrench before parts. This will ensure that the safety of the power turning the power tool on. A wrench or a key left tool is maintained. attached to a rotating part of the power tool may 26. Follow instruction fo
Summary of the content on the page No. 5
For tool with lock-off button To prevent the switch trigger from being accidentally WARNING: pulled, a lock-off button is provided. DO NOT let comfort or familiarity with product To start the tool, depress the lock-off button from either (gained from repeated use) replace strict adherence side and pull the switch trigger. Release the switch to safety rules for the subject product. trigger to stop. MISUSE or failure to follow the safety rules stated in this instruction manual may c
Summary of the content on the page No. 6
For tool with standard planer blades For tool with mini planer blades 1. Remove the existing blade, if the tool has been in 1. Socket wrench use, carefully clean the drum surfaces and the drum cover. To remove the blades on the drum, unscrew the three installation bolts with the socket wrench. The drum cover comes off together with the blades. 1 1. Socket wrench 007641 1. Bolt 1 1 2. Drum 3. Planer blade 4. Drum cover 007641 5. Adjusting plate 2 3 2. To install the blades
Summary of the content on the page No. 7
plate to slide the mini planer blade into position. side and the metal bracket on the other. The blade will be positioned by the planer blade 8. Tighten the three hex flange head bolts (with the locating lugs on the set plate. socket wrench provided) and rotate the drum to check clearances between the blade ends and the 6 1. Mini planer 1 tool body. blade 9. Check the three hex flange head bolts for final 5 2. Groove tightness. 3. Set plate 10. Repeat procedures 1 - 9 for other blade.
Summary of the content on the page No. 8
Connecting a vacuum cleaner 1. Recessed part 2. Protrusion 1. Vacuum cleaner 1 2 1 007801 007644 Dust bag (accessory) When you wish to perform clean planing operation, 1. Dust bag connect a Makita vacuum cleaner to your tool. Then 2. Chip discharge connect a hose of the vacuum cleaner to the chip opening discharge opening as shown in the figures. Elbow (optional accessory) 1. Elbow 2 1 007687 Attach the dust bag onto the chip discharge opening. The chip discharg
Summary of the content on the page No. 9
planing. Planing will be easier if you incline the When planing, move the tool with the edge fence flush workpiece in stationary fashion, so that you can plane with the side of the workpiece. Otherwise uneven somewhat downhill. planing may result. The speed and depth of cut determine the kind of finish. The power planer keeps cutting at a speed that will not CAUTION: result in jamming by chips. For rough cutting, the depth • The blade edge should be made to protrude of cut can be increas
Summary of the content on the page No. 10
Sharpening the planer blades 1. V groove (medium 1 For standard blades only amount of 2 Always keep your blades sharp for the best performance chamfering) 3 2. V groove (small possible. Use the sharpening holder to remove nicks amount of and produce a fine edge. chamfering) 1. Sharpening 3. V groove (great holder amount of chamfering) 007650 1 Use of chamfering rule (optional accessory) assures more tool stability when shiplapping. 1. Chamfering rule 002588 2. Screws
Summary of the content on the page No. 11
• Dressing stone • Dust bag assembly Remove and check the carbon brushes regularly. • Elbow Replace when they wear down to the limit mark. Keep • Socket wrench the carbon brushes clean and free to slip in the holders. • Chamfering rule assembly Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the rear cover. 1. Screwdriver 2. Rear cover 2 1 007651 Take out the worn carbon brushes, insert the new ones and
Summary of the content on the page No. 12
Makita Corporation Anjo, Aichi, Japan 12 884693E225
