Summary of the content on the page No. 1
E
fx-82ES PLUS
fx-85ES PLUS
fx-95ES PLUS
fx-350ES PLUS
User’s Guide
CASIO Worldwide Education Website
http://edu.casio.com
CASIO EDUCATIONAL FORUM
http://edu.casio.com/forum/
Summary of the content on the page No. 2
Contents Important Information ............................................................. 2 Sample Operations .................................................................. 2 Initializing the Calculator ........................................................ 2 Safety Precautions .................................................................. 2 Handling Precautions .............................................................. 2 Removing the Hard Case ..................................
Summary of the content on the page No. 3
Important Information • The displays and illustrations (such as key markings) shown in this User’s Guide are for illustrative purposes only, and may differ somewhat from the actual items they represent. • The contents of this manual are subject to change without notice. • In no event shall CASIO Computer Co., Ltd. be liable to anyone for special, collateral, incidental, or consequential damages in connection with or arising out of the purchase or use of this product and items that come with
Summary of the content on the page No. 4
• Do not subject the calculator to excessive impact, pressure, or bending. • Never try to take the calculator apart. • Use a soft, dry cloth to clean the exterior of the calculator. • Whenever discarding the calculator or batteries, be sure to do so in accordance with the laws and regulations in your particular area. * Company and product names used in this manual may be registered trademarks or trademarks of their respective owners. Removing the Hard Case Before using the calculator, sli
Summary of the content on the page No. 5
Reading the Display The display of the calculator shows expressions you input, calculation results, and various indicators. Input expression Indicators Math Math Math Math Calculation result • If a indicator appears on the right side of the calculation result, it means the displayed calculation result continues to the right. Use and to scroll the calculation result display. • If a indicator appears on the right side of the input expression, it means the displayed calculation continues to
Summary of the content on the page No. 6
Using Menus Some of the calculator’s operations are performed using menus. Pressing or , for example, will display a menu of applicable functions. The following are the operations you should use to navigate between menus. • You can select a menu item by pressing the number key that corresponds to the number to its left on the menu screen. • The indicator in the upper right corner of a menu means there is another menu below the current one. The indicator means another menu above. Use a
Summary of the content on the page No. 7
Deg Rad Gra Specifies degrees, radians or grads as the angle unit for value input and calculation result display. Note: In this manual, the symbol next to a sample operation indicates degrees, while the symbol indicates radians. Fix Sci Norm Specifies the number of digits for display of a calculation result. Fix: The value you specify (from 0 to 9) controls the number of decimal places for displayed calculation results. Calculation results are rounded off to the specif
Summary of the content on the page No. 8
Inputting Expressions and Values Basic Input Rules Calculations can be input in the same form as they are written. When you press the priority sequence of the input calculation will be evaluated automatically and the result will appear on the display. 4 sin30 (30 + 10 3) = 120 4 30 30 10 3 1 * 2 3 * * 1 * Input of the closing parenthesis is required for sin, sinh, and other functions that include parentheses. 2 * These multiplication symbols ( ) can be omitted. A multipli
Summary of the content on the page No. 9
Negative sign (–) Note: When squaring a negative value (such as –2), the value being squared must be enclosed in parentheses ( 2 2 ). Since x has a higher priority than the negative sign, 5th inputting 2 would result in the squaring of 2 and then appending a negative sign to the result. Always keep the priority sequence in mind, and enclose negative values in parentheses when required. 6th STAT Mode estimated values ( , , 1, 2) 7th Multiplication where the multiplication sign
Summary of the content on the page No. 10
As shown above, the value or expression to the right of the cursor after (INS) are pressed becomes the argument of the function that is specified next. The range encompassed as the argument is everything up to the first open parenthesis to the right, if there is one, or everything up to the first function to the right (sin(30), log2(4), etc.) This capability can be used with the following functions: , , ( ), ( ), ( ), , , ( ), . Overwrite Input Mode (Linear Display only) Y
Summary of the content on the page No. 11
Important: • Depending on the type of calculation result that is on the display when you press the key, the conversion process may take some time to perform. • With certain calculation results, pressing the key will not convert the displayed value. • You cannot switch from decimal form to mixed fraction form if the total number of digits used in the mixed fraction (including integer, numerator, denominator, and separator symbols) is greater than 10. Note: With Natural Display (MathO)
Summary of the content on the page No. 12
Degree, Minute, Second (Sexagesimal) Calculations Performing an addition or subtraction operation between sexagesimal values, or a multiplication or division operation between a sexagesimal value and a decimal value will cause the result to be displayed as a sexagesimal value. You also can convert between sexagesimal and decimal. The following is the input format for a sexagesimal value: {degrees} {minutes} {seconds} . Note: You must always input something for the degrees and minutes,
Summary of the content on the page No. 13
(Scrolls back.) 4 (Scrolls back again.) 2 Note: Calculation history data is all cleared whenever you press , when you change to a different calculation mode, when you change the display format, or whenever you perform any reset operation. Replay While a calculation result is on the display, you can press or to edit the expression you used for the previous calculation. 4 × 3 + 2.5 = 14.5
Summary of the content on the page No. 14
Independent Memory (M) You can add calculation results to or subtract results from independent memory. The “M” appears on the display when there is any value other than zero stored in independent memory. To clear the contents of M 0 (STO) (M) 0 To add the result of 10 5 to M (Continuing) 10 5 50 To subtract the result of 10 + 5 from M (Continuing) 10 5 (M–) 15 To recall the contents of M (Continu
Summary of the content on the page No. 15
Function Calculations For actual operations using each function, see the “Examples” section following the list below. : is displayed as 3.141592654, but = 3.14159265358980 is used for internal calculations. e : e is displayed as 2.718281828, but e = 2.71828182845904 is used for internal calculations. −1 −1 −1 sin, cos, tan, sin , cos , tan : Trigonometric functions. Specify the angle unit before performing calculations. See 1. −1 −1 −1 sinh, cosh, tanh, sinh , cosh , tanh : Hyperbol
Summary of the content on the page No. 16
nPr, nCr : Permutation (nPr) and combination (nCr) functions. See 13. Rnd : The argument of this function is made a decimal value and then rounded in accordance with the current number of display digits setting (Norm, Fix, or Sci). With Norm 1 or Norm 2, the argument is rounded off to 10 digits. With Fix and Sci, the argument is rounded off to the specified digit. When Fix 3 is the display digits setting, for example, the result of 10 ÷ 3 is displayed as 3.333, while the calculator maintai
Summary of the content on the page No. 17
To calculate (= 3 = 4.242640687...) to three decimal ' ' 2 2 × 3 places (Fix 3) (SETUP) (Fix) 2 3 ' 3 2 4.243 2 3 4.243 To convert rectangular coordinates (', ') to polar coordinates 8 8 2 2 (Pol) 2 (,) 2 r=2,θ=45 (Pol) 2 (,) 2 r= 2 θ= 45 To convert polar coordinates ( , 45°) to rectangular coordinates ' 2 (Rec) 2 (,) 45 X=1, Y=1 9 9 (5 + 3) ! = 40320
Summary of the content on the page No. 18
Statistical Calculations (STAT) To start a statistical calculation, perform the key operation (STAT) to enter the STAT Mode and then use the screen that appears to select the type of calculation you want to perform. To select this type of statistical calculation: Press this key: (Regression formula shown in parentheses) Single-variable (X) (1-VAR) Paired-variable (X, Y), linear regression ( y = A + Bx) (A+BX) Paired-variable (X, Y), quadratic regression 2 ( _+CX ) 2 ( y = A + Bx + Cx )
Summary of the content on the page No. 19
Important: • All data currently input in the Stat Editor is deleted whenever you exit the STAT Mode, switch between the single-variable and a paired- variable statistical calculation type, or change the Stat Format setting on the setup menu. • The following operations are not supported by the Stat Editor: , (M–), (STO). Pol, Rec, and multi-statements also cannot be input with the Stat Editor. To change the data in a cell: In the Stat Editor, move the cursor to the cell that contains
Summary of the content on the page No. 20
ST STA AT T (STAT) (1-VAR) 1 2 3 4 5 1 2 3 2 (STAT) (Var) ( ) (STAT) (Var) ( x) Results: Mean: 3 Population Standard Deviation: 1.154700538 To calculate the linear regression and logarithmic regression 3 3 correlation coefficients for the following paired-variable data and determine the regression formula for the strongest correlation: (x, y) = (20, 3150), (110, 7310), (200, 8800), (290, 9310). S
