Summary of the content on the page No. 1
F815D
Series
(Full-Size Single Board Computer)
INSTALLATION GUIDE
Installation Guide Revision A2
6007002815DA2
Summary of the content on the page No. 2
Summary of the content on the page No. 3
© COPYRIGHT All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
Summary of the content on the page No. 4
CONTENTS SECTION 1 INTRODUCTION 1 1.1 Unpacking F815D Series 1 1.2 Description 3 1.3 Features 3 1.3.1 Hardware Monitoring 4 1.3.2 I/O Shield Connector 4 1.3.3 F815D Series Overview 4 1.3.4 System Block Diagram 5 1.4 Specifications 6 SECTION 2 INSTALLATIONS 8 2.1 System Installation 8 2.1.1 CPU Installation 8 2.1.2 Memory Module Installation 9 2.1.3 Setting Jumpers 11 2.2 Board Layout 12 2.3 Jumper Setting 13 2.4 Connector’s Descript
Summary of the content on the page No. 5
CONTENTS SECTION 3 AWARD BIOS SETUP 29 3.1 BIOS Instructions 29 3.2 Main Menu 30 3.3 Standard CMOS Features 32 3.4 IDE Adapters 34 3.5 Advanced BIOS Features 36 3.6 Advanced Chipset Features 40 3.7 Integrated Peripherals 43 3.8 Power Management Setup 47 3.9 PnP/PCI Configurations 51 3.10 PC Health Status 53 3.11 Frequency/Voltage Control 55 3.12 Load Fail-Safe Default 57 3.13 Load Optimized Defaults 58 3.14 Supervisor/User Password Setting 59 3.1
Summary of the content on the page No. 6
iv
Summary of the content on the page No. 7
SECTION 1 INTRODUCTION 1.1 Unpacking F815D Series 1. Take out the F815D series unit from the carton box, check if the unit is properly secure in the plastic bag. 2. Check the contents of the carton box: Single Board Computer Installation Guide Floppy ribbon cable ATA-66/100 HDD ribbon cable Print ribbon cable Print & COM2 ribbon cable (F815D only) (F815D/V only) 1
Summary of the content on the page No. 8
Introduction ATX power control cable K/B-M/S extend to BP cable (4-pins to 4-pins) (6-pins to 6-pins) Driver CD 3. Optional Cable USB1.1 cable K/B-M/S extend to BP cable (6-pins to 5-pins) 2
Summary of the content on the page No. 9
Introduction 1.2 Description The F815D Series single board computer is optimized for socket 370 FC-PGA processor, supporting 100MHz and 133 MHz Front Side Bus, the memory can accommodate is up to 512 MB SDRAM. This board is based on ® the Intel 815EP/E chipset and is fully designed for harsh industrial environment. The F815D/V series is with on-die VGA function. The F815D series is one pure SBC. Them are for entry-level applications. The other I/O function include two serial po
Summary of the content on the page No. 10
Introduction 1.3.1 Hardware Monitoring Hardware monitoring allows you to monitor various aspects of your systems operations and status. The features include CPU temperature, voltage and RPM of fan. 1.3.2 I/O Shield Connector The SBC is equipped with an I/O bracket. Please use the appropriate I/O shield (figure 1). F815D Series F815D/V Series Figure 1: I/O bracket layout 1.3.3 F815D Series Overview Function / Model F815D F815D/V Chipset 815EP
Summary of the content on the page No. 11
Introduction 1.3.4 System Block Diagram Socket 370-pins for Pentium III / Celeron VRM Clock Processor ADDR CTRL DATA MCH (815EP) SDRAM CRT GMCH (815E) 100/133 X 2 544 BGA IDE Primary ATA100 IDE Secondary ICH2 360 BGA USB Port 1/2 USB USB Port 3/4 PCI BUS ISA BUS Super I/O ISA Bridge W83627HF W83628F FWH Keyboard Mouse COM Port LPT Port Floppy Figure 2: System Block Diagram 5 PICMG SLOT
Summary of the content on the page No. 12
Introduction 1.4 Specifications F815D Series: Processor: ® ® ® - Socket 370 processor, for Intel Celeron / Pentium !!! ( Coppermine™ / Tualatin™ ) processor Chipset: ® - Intel 815EP/815E AGPset Front Side Bus: - 66/100/133 MHz DRAM Module: - 168-pins DIMM x 2 for PC133 memory - Support SDRAM up to 512MB VGA Function: (F815D/V Series only) - On-die Video Accelerators controller Onboard I/O: - On-Chip I/O integrated with K/B, Mouse, FDD, Parallel and
Summary of the content on the page No. 13
Introduction Extended Function: - Hardware Monitoring function by W83781D - IrDA by pin-header Form Factor: - 13.3” x 4.8” (338 x 122mm) Weight: - 0.84lb (380 g.w.) --- F815D/V - 0.88lb (400 g.w.) --- F815D 7
Summary of the content on the page No. 14
SECTION 2 INSTALLATIONS 2.1 System Installation 2.1.1 CPU Installation Carefully follow the steps below in order to install the CPU: 1. Check and confirm that you are going to install correctly CPU type and pin numbers (figure 3). 2. Lift the releasing lever of the Socket 370. 3. Align the pin of the CPU against the pinholes of the Socket 370. Be sure to pay attention to the orientation of the CPU. Figure 3: CPU Socket 4. Push down the CPU into t
Summary of the content on the page No. 15
Installations Removing a CPU: 1. Before removing the CPU, turn off the F815D Series power; then wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cool down. 2. To remove the CPU, lift the releasing lever of the Socket 370. Note: The CPU and the heat radiation plate are hot. They may cause burns. To remove the CPU, reverse the installation steps. 2.1.2 Memory Module Installation Figure 4 display the notch marks and what they should
Summary of the content on the page No. 16
Installations Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static electricity and damaging the DIMM, ground yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM. 2. Do not touch the connector of the DIMM. Dirt residue may cause a malfunction. 3. Hold the DIMM with its notch to the front side of the F815D Series and insert it completely into the socket. A DIMM should be inserted into the inner soc
Summary of the content on the page No. 17
Installations 2.1.3 Setting Jumpers There are jumpers on the system board of the F815D Series. You can set the jumpers to make the necessary operations. Figure 6: Jumper Connector For any three-pins jumpers (Figure 6), the jumper setting is 1-2 when the jumper connects pin 1 and 2. The setting is 2-3 when pin 2 and 3 are connected and so on. You see one of the lines surrounding jumpers is thick, which indicates pin NO.1. To move a jumper from one position to
Summary of the content on the page No. 18
Installations 2.2 Board Layout Jumper & Connector Location CN4 CN21 CN22 CN14 CN19 CN17 JP1 CN9CN10 CN12 CN15 CN3 CN7 JP2 JP3 CN2 CN6 BAT1 CN18 CN20 BZ1 CN1 CN5 CN8 CN11 F815D REV1.0 12 DIMM1 IDE2 DIMM2 IDE1
Summary of the content on the page No. 19
Installations 2.3 Jumper Setting Table for Jumper Location Description: Use the information in the following table to change the jumpers. Jumpers Functions JP1 COM port setting select JP2 Clear CMOS setting select JP3 Watchdog Timer setting select 13
Summary of the content on the page No. 20
Installations In order to set up the correct configuration, here is the description about how to set the jumpers to enable/disable or change functions. All jumpers’ location please refer to jumper location diagram. COM port setting select: JP1 JP1 Function 1-2 3-4 5-6 7-8 9-10 11-12 RS-232 (Default) Off Off Off Off Off On RS-422 On (Term.) On (Term.) Off On On Off RS-485 On (Term.) On (Term.) On Off On Off Location: Clear CMOS setting select: JP2 Function JP
