Summary of the content on the page No. 1
ES-200-77
Multimedia Pentium III processor-based computer for HMI Applications
User's Manual
Summary of the content on the page No. 2
Copyright Notice Advantech Co., Ltd copyrights this document. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and r
Summary of the content on the page No. 3
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User’s Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or let
Summary of the content on the page No. 4
Packing List Before installing your equipment, make sure that the following materials have been received: • ES-200-77 • Accessory box, including: - CD kit for ES-200 Driver - 2-wire Power cord for 1.8 Meters - 30cm COM port cable - 30cm VGA cable - 30cm power cable for ES-3115/ES-3112/ES-3117 DC output - Wall mount bracket * 2 pcs. - Side mount for ES-3115/ES-3117 iron bracket * 4pcs. - Side mount for ES-3112 iron plate *2pcs If any of these items are missing or damaged, cont
Summary of the content on the page No. 5
Contents Chapter 1 Introduction.................................................................................1 1.1 Introduction.............................................................................................2 1.2 How to use this menu.............................................................................3 1.3 Specification ...........................................................................................4 1.4 Dimensions.....................................
Summary of the content on the page No. 6
Chapter 1 General Information This chapter gives information on ES- 200- 77 Sections • • How to Use • •
Summary of the content on the page No. 7
1.1 General Information The ES-200-77 PC is a multimedia Pentium III processor-based computer that is designed to serve as a human machine interface (HMI) and as a desktop computer. . You can select what application or integration for your system then decide which part you want to apply, or, of course, integrate both as a high performance panel PC. As PC module, this system with on-board PCI Ethernet controller, multi-COM port interfaces and a 16-bit stereo audio controller provides most
Summary of the content on the page No. 8
1.3 Specifications Feature: ● Fits with Advantech SBC boards. ● Buit-in 180-watt power supply. ● One PC-104 card or one half-length PCI card extendible ● Two 3.5” HDD can be installed ● One slim-type CD-ROM can be installed ● Multiple I/O interfaces for versatile applications ● Support Open-frame mechanical architecture for monitor ES-3112/ES-3115/ES-3117 attachable . ● Versatile combination solution for OFPC . Introduction: ES-200-77 is an SBC system box integrated with Advante
Summary of the content on the page No. 9
PC104 card expansion. ● I/O port: - 1* VGA port - 1* Parallel port - 4 * serial ports: RS-232 3, RS-232/422/485*1 - 2 * USB ports: Support USB1.1 up to 20Mb/sec. - 2 * PS2 ports: 1 * keyboard and 1* mouse - 1 * RJ 45 port: Supports 10/100T-Base Ethernet - 4 * Audio port: Supports 1* line in /1* line out / 1* Mic in / 1* Speaker out - 1 * DC output: Supports DC 3.3V =16.8A, 5V = 12A, 12V=10A, 5V=2A, -12V =0.8A output ● Dimensions (W * H * D): 353.6* 225.6 * 100mm ● Weight:
Summary of the content on the page No. 10
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Chapter 2 System Setup Sections include: • A Quick Tour of the Panel PC • Preparing for initial Use • Installation Procedures • Installing the Drivers
Summary of the content on the page No. 13
2.1 Quick Tour for ES-200-77 Before you start to set up ES-200, please take a moment to be familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the panel PC upright on the desktop, its front panel appears as shown in Figure 2-1. The sunken I/O section is at the bottom of the panel PC, as shown in Fig. 2-2. (The I/O section includes various I/O ports, including serial ports, parallel port, the
Summary of the content on the page No. 14
2.3.2 Connecting the keyboard and mouse Connect the PS/2 mouse and keyboard port on the I/O section of the panel PC. 2.3.3 Connecting the display Connect the display to the VGA sub in the bottom of ES-200-77 2.3.4 Switch on the power Switch on the power switch on the rear cover. 2.4 Running the BIOS setup program Your panel PC is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the panel PC's BIOS (Basic Input
Summary of the content on the page No. 15
drive. 2.6 Installing the drivers After installing your system software, you will be able to set up the Ethernet, VGA, audio, PCMCIA and touchscreen functions. All the drivers except the CD-ROM drive driver are stored in a CD-ROM disc entitled "Drivers and Utilities." The CD-ROM drive driver is stored in a floppy disk. Both the CD-ROM and the floppy disk can be found in your accessory box. To set up the CD-ROM function, insert the floppy disk with the CD-ROM drive driver into the floppy d
Summary of the content on the page No. 16
Chapter 3 Using the Panel PC This chapter details installing ES-200 hardware. Sections include: • CD-ROM Drive • PS/2 Mouse and Keyboard • PCI/ISA Bus Expansion • Parallel Port • Serial COM Ports • VGA Port • USB Ports • Audio Interface • Ethernet
Summary of the content on the page No. 17
3.1 CD-ROM drive To insert a CD-ROM disc, press the eject button of the CD-ROM drive. The yellow activity light will flash and the front panel will come out a short distance. Using your fingertips, hold the top and bottom of the front panel and pull it outward to the very end. Align the center hole of the CD-ROM disc with the center circle of the CD-ROM holding plate. Press the transparent ring around the center hole of the CD-ROM until you hear a click. Push the front panel of the CD-
Summary of the content on the page No. 18
PC, and then turn on the panel PC. 5. If necessary, run the panel PC's BIOS setup program to configure the parallel port to respond as required by your printer and software operating environment. 3.5 Serial COM ports There are three serial COM ports on the bottom of the rear cover. You can easily attach a serial device to the panel PC, such as an external modem or mouse. Follow these instructions: 1. Be sure the panel PC and any other peripheral devices you may have connected to the pan
Summary of the content on the page No. 19
Line out: Output audio to external devices such as speakers or earphones. Line in: Input audio from an external CD player or radio. 1. Connect the audio device to the system. 2. Install the driver before you use the device. 3.9 Ethernet External devices on your network may be connected to the system through the external Ethernet port located on the rear side of the system unit. 1. Be sure the panel PC is turned off. 2. Connect the external device(s) to the panel PC. 3. Turn on the pan
