Summary of the content on the page No. 1
IWILL DJ800
Motherboard
User’s Manual
FB25634000
Summary of the content on the page No. 2
User’s Manual DJ800 Motherboard ii
Summary of the content on the page No. 3
Preface Disclaimer The manufacturer makes no representations or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, the manufacturer reserves the right to revise this publication or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or change. Trademarks Microsoft and Window
Summary of the content on the page No. 4
User’s Manual DJ800 Motherboard T able o f C ontents 1: Overview .............................................................................1-1 Packing list ................................................................................. 1-1 Safety Notice .............................................................................. 1-2 DJ800 Specification .................................................................. 1-5 2: Components and Jumper Setting .........................2-1 Mainb
Summary of the content on the page No. 5
Preface 4: BIOS Setup .........................................................................4-1 Starting the BIOS Setup ............................................................ 4-1 Using the BIOS Setup Utility .................................................... 4-3 Main Menu................................................................................. 4-5 Advanced Menu ......................................................................... 4-6 Boot Menu .............................
Summary of the content on the page No. 6
Chapter 1 Overview
Summary of the content on the page No. 7
Chapter 1 Package DJ800 Motherboard Three jumper caps (Extra caps in case original caps get lost) One Power Installation CD (contains drivers and utilities) DJ800 User’s manual Rear panel I/O shield Two sets of SATA cables One ATA-66/100 IDE cable One floppy disk drive cable Two Hat Springs for CPU cooler 1-1
Summary of the content on the page No. 8
Overview Overview DJ800 Motherboard YOU MUST HAVE ENOUGH SYSTEM INTEGRATION KNOWLEDGE BEFORE THE INSTALLATION General Safety Precautions Keep the area around the Server clean and free of clutter. Servers weigh a lot. When lifting the system, two people should lift slowly from opposite ends with their feet spread out to distrib- ute the weight. Always keep your back straight and lift with your legs. Place the chassis top cover and any system components that have been removed away from the syst
Summary of the content on the page No. 9
Chapter 1 Use a grounded wrist strap designed to prevent static discharge. Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready for use. Touch a grounded metal object before removing the board from the antistatic bag. Do not let components or PCBs come into contact with your clothing, which may retain a charge even if you are wearing a wrist strap. Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or contact
Summary of the content on the page No. 10
Overview Overview DJ800 Motherboard Getting Help If a problem arises with your system during Installation or Operation, you should first ask your dealer for help as they have most likely config- ured your system. They generally have the best grasp of your issues and the fastest response for your symptoms. If your dealer is near your location, it is recommended that you first bring your system to them to have it ser- viced instead of attempting to solve the problem yourself. If those options don’
Summary of the content on the page No. 11
Chapter 1 DJ800 Specifications ® Intel Dual Xeon Socket 604 CPUs Processor Supports 800MHz FSB Intel E7525 Chipset MCH Intel ICH5R Chipset Intel PXH Winbond 83627 HF 8 DIMMs for 240-pin DDR2 400 DIMM sockets Uses Registered DDR2 with ECC or Non-ECC memory Memory Supports total system memory size of up to 16GB Intel 82541PI Gigabit Ethernet Controller On-Board One RJ-45 connectors for GbE LAN Support PME Integrated Analog Device AD1980 Professional 6-channel Audio wit
Summary of the content on the page No. 12
Overview Overview DJ800 Motherboard 34-pin Floppy Connector Internal I/O connector 4-pin CD-In and Aux-In audio input connector 2x 40-pin IDE connectors, supports up to four (4) Enhanced IDE devices IDE Bus Dual Channel Master Mode Ultra DMA 100/66/33 PS/2 mouse and keyboard connectors 1 x UART 16550 serial port (COM1) 1 x 25-pin parallel port with ECP/EPP support Rear Panel I/O 4 x on board USB 2.0 ports 1 x IEEE-1394 port 1 x S/PDIF Out Rear Out and Center Out Audio Phone Jacks -
Summary of the content on the page No. 13
Chapter 2 Components and Jumper Setting
Summary of the content on the page No. 14
DIMM B4 DIMM A1 PCI-Express x16 PCI-Express x4 PCI-X 64/133 PCI-X 64/100 PCI-X 64/100 PCI 32/33 Hardware Installation Components and Jumper Setting DJ800 Motherboard MAINBOARD MAP MAINBOARD MAP J57 J63 JP18 J46 JP19 J48 JP10 J66 JP10A J67 J68 J69 J34 J34A CPU2 CPU1 JP1 J43 Floppy Primary Secondary JP16 2-1
Summary of the content on the page No. 15
Chapter 2 Components List CPU1; CPU2 Intel Xeon Socket604 Processor Primary; Secondary IDE Driver Connectors Floppy Floppy Disk Driver Connector PCI Slots PCI-Express x16, x4 Slots; PCI-X 100,133; PCI DIMM B4~A1 Memory Socket for DDR2 Memory JP1 Clear CMOS Header JP10 and JP10A Memory Voltage Select Jumper JP16 BIOS Flash Protect Jumper JP18 USB Power Select Jumper JP19 LAN Power Select Jumper J34 &J34A USB 2.0 Ports and Header J43 Front Panel Switch Header J46 WOL Connector J48 SMBus Connector
Summary of the content on the page No. 16
Hardware Installation Components and Jumper Setting DJ800 Motherboard Jumper Setting JP1: Clear CMOS Header The onboard button cell battery powers the CMOS RAM. It con- tains all the BIOS setup information. Keep the jumper connected to pins 1-2 (Default) to retain the RTC data as shown below. 1-2 2-3 1 2 Normal (Default) Clear CMOS 3 Under certain circumstances, you will need to reset system settings. Follow these instructions to clear the CMOS RTC data: 1. Turn off the computer. 2. Short pins 2
Summary of the content on the page No. 17
Chapter 2 JP10 and JP10A: Memory Voltage Select Jumper This header lets you adjust the memory voltage. JP10A JP10 VDDR JP10 JP10A 1.8V 1-2 1-2 1.85V 1-2 2-3 1.9V 2-3 1-2 1.95V 2-3 2-3 JP16: BIOS Flash Protect Jumper This jumper protects the system from unnecessary updating or flashing of the BIOS. It secures the BIOS therefore prevents accidental overwriting of the data stored in flash memory. JP16 1-2 By Soft 12 3 2-3 Lock Open Unlock JP18: USB Power Select Jumper This header lets you set your
Summary of the content on the page No. 18
Hardware Installation Components and Jumper Setting DJ800 Motherboard JP19: LAN Power Select Jumper This header lets you set your LAN connectors power status. You can choose power standby or not. 1-2 2-3 1 2 VCC33 Stand By VCC33 3 J57: Front Audio Jumper This header lets you enable or disable the function of the front audio connector. 9 1 W/O FRONT WITH FRONT J57 AUDIO AUDIO CONNECTOR CONNECTOR 5-6 SHORT OPEN 10 9-10 SHORT OPEN 2-5
Summary of the content on the page No. 19
Chapter 2 Rear Panel I/O Ports This is an illustration of the Mainboard rear I/O port array Mouse Parallel LAN IEEE1394 Line In Line Out Mic In Keyboard COM1 Rear Out Center Out S/PDIF USB2.0 PS/2 Mouse Connector (6-pin Female) The system will direct IRQ12 to the PS/2 mouse if one is detected. If no mouse is detected, IRQ12 will be free for expansion cards to use. PS/2 Keyboard Connector (6-pin Female) This connection is for standard keyboards using a PS/2 (mini DIN) plug. This connector will n
Summary of the content on the page No. 20
Hardware Installation Components and Jumper Setting DJ800 Motherboard IEEE 1394/ FireWire Connector (6-pin Male) You have one (1) onboard IEEE 1394 connector port for connecting FireWire devices. Refer to IEEE 1394 Ports & Header for more information. Serial Port (COM1) Connector (9-pin Male) The COM1 serial port can be used for pointing devices or other se- rial devices. See BIOS for more on serial port setup. Parallel Printer Connector (25-pin Female) You can enable the parallel port and choos
