Summary of the content on the page No. 1
SBC Series
Single Board Computer
Half-size PICMG 1.3
with LAN, Audio, SATA
SEH-9450-LAS
User’s Manual
CONTEC CO.,LTD.
Summary of the content on the page No. 2
Check Your Package Thank you for purchasing the CONTEC product. The product consists of the items listed below. Check, with the following list, that your package is complete. If you discover damaged or missing items, contact your retailer. Product Configuration List - Industrial PICMG CPU Board (SEH-9450-LAS) …1 - Product Guide …1 - IPC Precaution List …1 - Driver disk utilities * 1 (CD-ROM) …1 - IDE 40 pin Ribbon Cable …1 - SATA Cable …2 - 2 serial Ports (9 pin D-SUB male x
Summary of the content on the page No. 3
Copyright Copyright 2007 CONTEC CO., LTD. ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any
Summary of the content on the page No. 4
Table of Contents Check Your Package ................................................................................................................................i Copyright .................................................................................................................................................ii Trademarks ..............................................................................................................................................ii Caution ab
Summary of the content on the page No. 5
System FAN Connector: FAN2.............................................................................................................15 Front Panel Connector: FP1............................................................................................................16 Power Switch (Power BT) ..............................................................................................................16 Reset Switch (RESET)..............................................................
Summary of the content on the page No. 6
8. BIOS SETUP 37 Introduction............................................................................................................................................ 37 Starting Setup ................................................................................................................................. 37 Using Setup..................................................................................................................................... 38 Getting Help .........
Summary of the content on the page No. 7
SEH-9450-LAS vi
Summary of the content on the page No. 8
1. Introduction 1. Introduction About the SBC This product is a half-size sized single-board computer that supports PICMG1.3. It uses Intel (R) 945GME Chipset. The supported CPU is Intel (R) Core Duo / Core 2 Duo processor. For the memory, up to 4 GB (total capacity : 3.1GB) of DDR2 SDRAM can be mounted. The all-in-one design features a wide variety of interfaces including Analog RGB, LVDS, SDVO, USB2.0 x 4, SATA x 2, 1000BASE-T/100BASE-TX, audio, IDE, serial and PS/2 Keyboard/Mouse
Summary of the content on the page No. 9
1. Introduction Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably. Web Site Japanese http://www.contec.co.jp/ English http://www.contec.com/ Chinese http://www.contec.com.cn/ Latest product information CONTEC provides up-to-date information on products. CONTEC also provides product manuals and various technical documents in the PDF. Free download You can download updated driver software and differential fil
Summary of the content on the page No. 10
1. Introduction Safety Precautions Understand the following definitions and precautions to use the product safely. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely. DANGER indicates an imminently hazardous situation which, if not DANGER avoided, will result in death or serious in
Summary of the content on the page No. 11
1. Introduction Environments Use this product in the following environment. If used in an unauthorized environment, the board may overeat, malfunction, or cause a failure. Operating temperature 0 - 60°C Operating humidity 10 - 90%RH (No condensation) Corrosive gases None Floating dust particles Not to be excessive Inspection Inspect the product periodically as follows to use it safely. - Check that the board has no dust or foreign matter adhering. - Check that the bus connector
Summary of the content on the page No. 12
2. System Reference 2. System Reference Specification Table 2.1. Functional Specifications < 1 / 2 > Type Specifications Intel(R) Core Duo / Core 2 Duo (FSB 533 / 667 MHz) Supported CPU Built in CPU Cache Socket M Processor socket Up to MAX 4G, DDR2 400 / 533 / 667, 200 pin SO-DIMM Socket X 2 *1 Memory (Option) Intel(R) 945GME+ ICH7M-DH Chipset Phoenix AwardBIOS, PnP support BIOS Built in Intel 945GME, One Analog RGB D-Sub 15pin connector. VGA One LVDS (18bit) I/F: (One b
Summary of the content on the page No. 13
2. System Reference Table 2.1. Functional Specifications < 2 / 2 > Type Specifications Software programmable 255 levels (1 - 255sec). Watchdog Timer When time up: Reset None General-purpose I/F Monitoring of the temperature of CPU and board, power supply voltage, and fan speed Hardware Monitor RTC The coin type Lithium battery specification is shown in table Specification CR2450 Voltage 3V Capacity 620mAh Weigh 6.3g * Backup time: Over 7 years at 25ºC. * Real Time Clock accou
Summary of the content on the page No. 14
2. System Reference Power Management Features - Support both ACPI (Advanced Configuration and Power Interface) and legacy (APM) power management. - ACPI v2.0 compliant - APM v1.2 compliant - PCI bus clock run, Power Management Enable (PME) control, all with hardware automatic wake-up - Multiple suspends power plane controls and suspends status indicators - Normal, doze, sleep, suspend and conserve modes - Global and local device power control Power Requirements Your system requires a
Summary of the content on the page No. 15
2. System Reference Connector & Jumper Location Top side COM1 COM2 JCOM1 SATA1 SATA2 IDE1 FAN1 AUDIO1 TPM1 FP1 JP1 USB1 LAN1 USB2 USB3 VGA1 PWR1 KB/MS1 FAN2 SDVO1 LVDS1 LVDS2 JBAT1 Bottom side CF1 DIMM1 DIMM2 PCI1 Figure 2.1. Connector & Jumper Location SEH-9450-LAS 8
Summary of the content on the page No. 16
2. System Reference Table 2.3. SBC Connectors Item Content AUDIO1 Audio Connector CF1 Compact Flash Slot COM1 Serial 1 Port Connector COM2 Serial 2 Port Connector DIMM1, DIMM2 DIMM Memory Socket FAN1 CPU FAN Connector FAN2 System FAN Connector FP1 Front Panel Connector IDE1 Primary IDE Connector JBAT1 CMOS / ROM Clear JP1 CF Setting KB/MS1 PS/2 Keyboard / Mouse Connector LAN1 10/100/Giga LAN Connector LVDS1, LVDS2 LVDS Connectors PCI1 Mini PCI Slot PWR1 Power Connector SATA1,
Summary of the content on the page No. 17
PICMG 1.3 Mini PCI Golden Finger DATA CTRL DMI BUS LPC BUS ADDR 2. System Reference Block Diagram CK-410M IMVP6 CPU Socket for Yonah & ISC954226 ISL6262CR Merom R.G.B. R.G.B. Channel A D-SUB 15Pin GMCH DDR2 667 Dual-Channel 945GME Channel B LVDS 18bit LVDS BUS 2Channel PICMG 1.3 BUS IDE Primary & DMA33/66/100 CompactFlash ICH7M-DH USB Interface USB 2.0 PCI Interface Audio Codec AC LINK ALC202A LPC IO W83627EHG SATA SATA Interface Conncetor Keyboard & Serial Port Mouse (RS232/RS422/RS485) LAN P
Summary of the content on the page No. 18
3. Hardware Installations 3. Hardware Installations This chapter provides information on how to use the jumpers and connectors on the product in order to set up a workable system. Installation procedure (1) Confirm the power supply is off. (2) Install the processor with correct orientation. (3) Mount the Heat sink on the top of the processor. (The heat sink with a fan connects a fan cable to the fan connector on a board.) (4) Insert the DDR2 SDRAM module with correct orientation. (5)
Summary of the content on the page No. 19
3. Hardware Installations CPU Installation: This product supports a single Intel socket-M type Core Duo processor or Core 2 Duo processor. The processor’s VID pins automatically program the voltage regulator on the CPU card to the required processor voltage. The host bus speed is automatically selected. The processor connects to the CPU card through the socket M. The socket-M comes with a turn lock to secure the processor. Make sure the notch on the corner of the CPU corresponds with
Summary of the content on the page No. 20
3. Hardware Installations Audio Connector: AUDIO1 This connector connects the Audio jack cable. Table 3.2. Audio Connector PIN No. Function PIN No. Function AUDIO1 10 9 10 LINE-IN-L 9 LINE-IN-R 8 GND 7 GND 6 MICIN 5 NC 2 1 4 GND 3 GND LINE-OUT-L LINE-OUT-R 2 1 Compact Flash Slot: CF1 This product provides a Compact Flash interfaces. This interface is a very small removable mass storage device. It provides compatibility plus True IDE functionality compatible with ATA/ATA-4. Tab
