Summary of the content on the page No. 1
Table of Contents
1. PRECAUTIONS FOR SAFETY AND USE _____________________ 19
2. INSTALLING THE OVEN __________________________________ 21
3. DESCRIPTION OF CONTROLS ____________________________ 23
4. USING THE OVEN_______________________________________ 24
5. CLEANING AND MAINTENANCE ___________________________ 29
6. EXTRAORDINARY MAINTENANCE _________________________ 31
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified
Summary of the content on the page No. 2
Introduction 1. PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE. WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS OVEN IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS
Summary of the content on the page No. 3
Introduction THE APPLIANCE BECOMES VERY HOT DURING USE. OVEN GLOVES SHOULD ALWAYS BE WORN. THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE SIDE OF THE OVEN. THIS NAMEPLATE MUST NEVER BE REMOVED. THE APPLIANCE IS DESIGNED FOR PROFESSIONAL USE BY TRAINED STAFF. KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT. BEFORE USE, WASH THE PANS WITH A SPECIAL OVEN-WARE DETERGENT (NEVER USE ABRASIVE PRODUCTS). T
Summary of the content on the page No. 4
Instructions for the Installer 2. INSTALLING THE OVEN The oven is designed for free-standing installation on a horizontal work- top. It must be far enough from the wall behind it to allow easy access to the terminal board for connection of the power supply lead. Installation must be carried out by a qualified engineer in compliance with the relevant EEC DIRECTIVES. 2.1 Electrical connection Check that the power supply voltage and size are as specified on the nameplat
Summary of the content on the page No. 5
Instructions for the Installer In case of connection to the electrical mains by means of socket and pin, the connection must be completed with a three-pin plug of suitable rating (25A), or, for operation at 380-415V2N ∼ or 380-415V3N ∼, a five-pin plug (16A). The power supply plug and wall socket must be of the same type (in compliance with CEI standards). Check that the power supply line is properly earthed. The use of reductions, adapters or junctions is not recommended. If a
Summary of the content on the page No. 6
Instructions for the User 3. DESCRIPTION OF CONTROLS START BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, edit programs and start cooking cycles. It also selects the operating power. STOP BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, edit programs and terminate cooking cycles. It also selects the operating power. DISPLAY D
Summary of the content on the page No. 7
Instructions for the User 4. USING THE OVEN 4.1 Precautions and General Advice When the oven is used for the first time, it should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process. If you have to carry out any procedures on foods, leave the door open for as short a time as possible to ensure the temperautre inside the oven does not drop far enough to impair cooking results. 4.2 Setting the time A
Summary of the content on the page No. 8
Instructions for the User 4.4 Program selection This oven has 15 different cooking programs, including: 14 user-editable programs for fan-mode cooking (P1 to P14); 1 manual editable program for fan-mode cooking ( ). The following table shows the parameters for each program. Uprh Ut °C U Ct preheating cooking cooking time temperature temperature P1 Same as edited Ut°C Preset 185°C Preset 16‘ P2 Same as edited Ut°C Preset 190°C Preset 15’ P3…P14 Same as edited Ut°C Editable E
Summary of the content on the page No. 9
Instructions for the User Press START to confirm the start of the program. The program starts, performing the preheating stage; the display shows "PrEh". When the preheating is complete, a "BEEP" sounds to indicate that cooking can start, and the message "PrEh" flashes on the display. Keep START pressed for a few seconds to start cooking; another BEEP sounds to signal the switch from preheating to cooking. (If START is not pressed after the beep, the temperature is held constant fo
Summary of the content on the page No. 10
Instructions for the User The display shows U Ct. Press START to display the cooking time. Press START or keep it pressed to increase the cooking time (from 1 min. to 99 min.). Press STOP to complete the program editing procedure. The display shows UEnd. The parameters set are now saved in the chosen program. 4.8 Manual cooking Use the knob to select the manual program ( ). The special feature of this user-editable program is that the cooking parameters set are not retained
Summary of the content on the page No. 11
Instructions for the User 4.9 Rapid cooling The oven has a special function which allows its interior to be cooled quickly. To activate this function, turn the function selector to "0", open the door and press the START key for at least 2 seconds. The fans inside the oven will come into operation with the heating elements off. To stop the function, press the STOP key. 4.10 Key to the oven's beep sounds All the beep sounds the oven emits are different from each other, in order t
Summary of the content on the page No. 12
Instructions for the User 5. CLEANING AND MAINTENANCE Important: never point jets of water straight at the oven and do not use high- pressure water cleaners. Before carrying out any operation, disconnect the oven from the electricity supply. 5.1 Cleaning stainless steel To keep stainless steel in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. When cleaning and caring for stainless steel surfaces,
Summary of the content on the page No. 13
Instructions for the User 5.2 Cleaning the inside of the oven To keep the oven in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. Remove all removable parts. Remove the side runners by removing the hook "C" from the hole or pin "D" (depending on the model) and the pin "A" from the hole "B" on the bottom of the oven. • Clean the oven shelves and side runners with hot water and non- abrasive detergents, rinse and d
Summary of the content on the page No. 14
Instructions for the User 6. EXTRAORDINARY MAINTENANCE Occasionally, the oven will require minor servicing procedures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. Before carrying out any operation, disconnect the oven from the electricity supply. 6.1 Changing the light bulb Remove the protective cover A. Replace the light bulb B with anothe
Summary of the content on the page No. 15
Instructions for the User 6.2 Removing the door Open the door completely and insert the pins (supplied) into the holes from the inside. Close the door to an angle of about 45° and lift it off. To reassemble, fit the hinges into their grooves, then lower the door into place and extract the pins. 6.3 Oven door gasket To allow thorough cleaning of the oven, the door gasket can be removed. Before removing the gasket, remove the oven door as described above. Once the door
