Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS FOR PART 99-8156
APPLICATIONS
LEXUS LS SERIES
1990-1994
99-8156
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Radio Housing Brackets • D) Trim Plate
E) (6) #8 Phillips Screws
B
C
A
D
E
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2007 METRA ELECTRONICS COR
Summary of the content on the page No. 2
99-8156 TABLE OF CONTENTS Dash Disassembly - Lexus LS Series 1990-1994 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
99-8156 DASH DISASSEMBLY LEXUS LS SERIES 1990-1994 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Carefully pry out and remove ashtray assembly below radio. (Figure A) 3 Using a panel removal tool or small flat blade screwdriver gently pry out on the top of the A/C vent assembly and remove. (Figure B) 4 Remove (4) screws securing the fac- B tory radio/climate control assembly. Unplug and remove assembly. (Figure C) 5 Remove (4) screws securing the cli-
Summary of the content on the page No. 4
99-8156 KIT PREPARATION LEXUS LS SERIES 1990-1994 DIN MOUNT RADIO PROVISION WITH POCKET ISO MOUNT RADIO PROVISION WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the corresponding radio hous- ing bracket to the radio housing using the included Phillips screws. (Figure A) 2 Slide the factory climate control into the assembled radio housing brack- ets/radio housing assembly and secure with the factory hardware. (Figure B) Continue to kit assembly
Summary of the content on the page No. 5
99-8156 KIT ASSEMBLY LEXUS LS SERIES 1990-1994 DIN MOUNT RADIO PROVISION WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps in place. (Figure B) Continue to final assembly. B 3
Summary of the content on the page No. 6
99-8156 KIT ASSEMBLY LEXUS LS SERIES 1990-1994 ISO MOUNT RADIO PROVISION WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until the side clips engage. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly. B 4
Summary of the content on the page No. 7
99-8156 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse
Summary of the content on the page No. 8
99-8156 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 12/05/07 © COPYRIGHT 2007 METRA ELECTRONICS CORPORATION INST99-8156
