Summary of the content on the page No. 1
Prestige 2304R-P1
VoIP Station Gateway
Support Notes
Version 3.60
April. 2006
Summary of the content on the page No. 2
Prestige 2304 Support Notes INDEX Application Notes.........................................................................................................5 General Application Notes.....................................................................................5 Internet Connection........................................................................................5 Setup the Prestige as a DHCP Relay............................................................10 Configure
Summary of the content on the page No. 3
Prestige 2304 Support Notes How many network users can the SUA/NAT support?...............................78 What are Device filters and Protocol filters?...............................................78 Why can't I configure device filters or protocol filters? ..............................79 Product FAQ ........................................................................................................79 What is the Prestige Internet Access Sharing Router?.......................
Summary of the content on the page No. 4
Prestige 2304 Support Notes What is DDNS?............................................................................................89 When do I need DDNS service? ..................................................................89 What DDNS servers does the Prestige support?..........................................89 What is DDNS wildcard?.............................................................................89 Does the Prestige support DDNS wildcard?........................
Summary of the content on the page No. 5
Prestige 2304 Support Notes Application Notes General Application Notes Internet Connection A typical Internet access application of the Prestige is shown below. For a small office, there are some components needs to be checked before accessing the Internet. • Before you begin • Setting up the Windows • Setting up the Prestige router • Troubleshooting • Before you begin The Prestige is shipped with the following factory default: 1. IP address = 192.168.1.1, subnet mask
Summary of the content on the page No. 6
Prestige 2304 Support Notes • If you only have one PC, connect the PC's Ethernet adapter to the Prestige's LAN port with a crossover (red one) Ethernet cable. • If you have more than one PC, both the PC's Ethernet adapters and the Prestige's LAN port must be connected to an external hub with straight Ethernet cable. 2. TCP/IP Installation You must first install TCP/IP software on each PC before you can use it for Internet access. If you have already installed TCP/IP, go to the next
Summary of the content on the page No. 7
Prestige 2304 Support Notes The following procedure is for the most typical usage of the Prestige where you have a single-user account (SUA). The Prestige supports embedded web server that allows you to use Web browser to configure it. Before configuring the router using Browser please be sure there is no Telnet or Console login. 1. Retrieve Prestige Web Please enter the LAN IP address of the Prestige router in the URL location to retrieve the web screen from the Prestige. The defau
Summary of the content on the page No. 8
Prestige 2304 Support Notes 3. Configure Prestige for Internet access by using WIZARD SETUP 8 All contents copyright (c) 2005 ZyXEL Communications Corporation.
Summary of the content on the page No. 9
Prestige 2304 Support Notes The Web screen shown below takes PPPoE as the example. 9 All contents copyright (c) 2005 ZyXEL Communications Corporation.
Summary of the content on the page No. 10
Prestige 2304 Support Notes Select “Dynamic＂ if the ISP provides the IP dynamically, otherwise select “Use Fixed IP address＂ and enter the static IP given by ISP in the box following“MY WAN IP Address＂field. Setup the Prestige as a DHCP Relay • What is DHCP Relay? DHCP stands for Dynamic Host Configuration Protocol. In addition to the DHCP server feature, the P2602 supports the DHCP relay function. When it is configured as DHCP server, it assigns the IP addresses to the LAN
Summary of the content on the page No. 11
Prestige 2304 Support Notes • Setup the Prestige as a DHCP Client 1. Toggle the DHCP to Relay in menu 3.2 and enter the IP address of the DHCP server in the 'Relay Server Address' field. Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP= Relay TCP/IP Setup: Client IP Pool: Starting Address= N/A IP Address= 192.168.1.1 Size of Client IP Pool= N/A IP Subnet Mask= 25
Summary of the content on the page No. 12
Prestige 2304 Support Notes Configure an Internal Server Behind SUA • Introduction If you wish, you can make internal servers (e.g., Web, ftp or mail server) accessible for outside users, even though SUA makes your LAN appear as a single machine to the outside world. A service is identified by the port number. Also, since you need to specify the IP address of a server in the Prestige, a server must have a fixed IP address and not be a DHCP client whose IP address potentially ch
Summary of the content on the page No. 13
Prestige 2304 Support Notes • Port numbers for some services Service Port Number FTP 21 Telnet 23 SMTP 25 DNS (Domain Name Server) 53 www-http (Web) 80 Configure a PPTP server Behind SUA • Introduction 13 All contents copyright (c) 2005 ZyXEL Communications Corporation.
Summary of the content on the page No. 14
Prestige 2304 Support Notes PPTP is a tunneling protocol defined by the PPTP forum that allows PPP packets to be encapsulated within Internet Protocol (IP) packets and forwarded over any IP network, including the Internet itself. In order to run the Windows 9x PPTP client, you must be able to establish an IP connection with a tunnel server such as the Windows NT Server 4.0 Remote Access Server. Windows Dial-Up Networking uses the Internet standard Point-to-Point (PPP) to provide a s
Summary of the content on the page No. 15
Prestige 2304 Support Notes This application note explains how to establish a PPTP connection with a remote private network in the Prestige SUA case. In ZyNOS, all PPTP packets can be forwarded to the internal PPTP Server (WinNT server) behind SUA. The port number of the PPTP has to be entered in the SMT Menu 15 for Prestige to forward to the appropriate private IP address of Windows NT server. • Example The following example shows how to dial to an ISP via the Prestige and then
Summary of the content on the page No. 16
Prestige 2304 Support Notes • Before making a VPN connection from Win9x to WinNT server, you need to connect Prestige router to your ISP first. • Enter the IP address of the PPTP server (WinNT server) and the port number for PPTP as shown below. When you have finished the above settings, you can ping to the remote Win9x client from WinNT. This ping command is used to demonstrate that remote the Win9x can be reached across the Internet. If the Internet connection between two LANs
Summary of the content on the page No. 17
Prestige 2304 Support Notes VPN dial-up dialog box. You can check this Internet IP address from PNC Monitor or SMT Menu 24.1. If the Internet IP address is a fixed IP address provided by ISP in SUA mode, then you can always use this IP address for reaching the VPN server. In the following example, the IP address '140.113.1.225' is dynamically assigned by ISP. You must enter this IP address in the 'VPN Server' dialog box for reaching the PPTP server. After the VPN link is establishe
Summary of the content on the page No. 18
Prestige 2304 Support Notes • Filter Types and SUA Conceptually, there are two categories of filter rules: device and protocol. The Generic filter rules belong to the device category; they act on the raw data from/to LAN and WAN. The IP and IPX filter rules belong to the protocol category; they act on the IP and IPX packets. 18 All contents copyright (c) 2005 ZyXEL Communications Corporation.
Summary of the content on the page No. 19
Prestige 2304 Support Notes In order to allow users to specify the local network IP address and port number in the filter rules with SUA connections, the TCP/IP filter function has to be executed before SUA for WAN outgoing packets and after the SUA for WAN incoming IP packets. But at the same time, the Generic filter rules must be applied at the point when the Prestige is receiving and sending the packets; i.e. the ISDN interface. So, the execution sequence has to be changed. The log
Summary of the content on the page No. 20
Prestige 2304 Support Notes same error if you try to activate a Generic filter rule in a filter set that has already had one or more active TCP/IP (or IPX) filter rules. Menu 21.1.1: Menu 21.1.1 - Generic Filter Rule Filter #: 1,1 Filter Type= Generic Filter Rule Active= Yes Offset= 0 Length= 0 Mask= N/A V
