Summary of the content on the page No. 1
XiNCOM Cor XiNCOM Corp p. .
Summary of the content on the page No. 2
Summary of the content on the page No. 3
XiNCOM Corp. TABLE OF CONTENTS 1: INTRODUCTION ..............................................................................................................................3 Twin WAN Router Features .........................................................................................................3 Warranty Information ...................................................................................................................5 Package Contents .................................
Summary of the content on the page No. 4
System Status.............................................................................................................................63 WAN Status .................................................................................................................................66 NAT Status ..................................................................................................................................67 APPENDIX A SPECIFICATIONS ...........................................
Summary of the content on the page No. 5
XiNCOM Corp. All trademarks and trade names are the properties of their respective owners. 1: Introduction Congratulations on the purchase of your new Twin WAN Router. The Twin WAN Router provides you with shared internet across the entire LAN along with Load Balancing and Automatic Failover features. This is the most typical network setup where the router is used to accommodate. Figure 1: XC-DPG Twin WAN Router (502 Shown) Twin WAN Router Features • 2 x 10/100 WAN (Wide Area Netw
Summary of the content on the page No. 6
• Stateful Packet Firewall: Protects your network using advanced Stateful Packet Inspection against unwanted access from the outside along with malicious hackers, DoS and DDoS attacks. Twin WAN Router Features (Continued) • Advanced NAT features: Access Filters, DMZ, DDNS, Remote Management, Dynamic or Static Routing, Special Applications, URL blocking, Virtual Servers, SNMP. Supports up to 100,000 concurrent sessions on the 502 and 602 and 10,000 on the 402. • DHCP Server: The built-i
Summary of the content on the page No. 7
XiNCOM Corp. Warranty Information • 30 day money back guarantee • 5-Year Limited Warranty • Technical support and firmware upgrade for the life of the product. If you need technical support you can contact us via Live Chat on our website, email us at support@xincom.com or call: 888.494.6266 (USA/Canada) 503.982.1328 (International) You can download and read all about our latest firmware releases and view our technical support library can be viewed by going to http://support.xi
Summary of the content on the page No. 8
Physical Details Front Panel of XC-DPG402: Front Panel of XC-DPG502: Front Panel of XC-DPG602: Operation of the Front Panel LED is as follows: LAN LINK/ACT ON – Physical connection or data in/out. OFF – No physical connection. 10M/100M ON – The corresponding LAN port is using 100BaseT. OFF – 10BaseT connection on the corresponding LAN port or no connection. WAN LINK/ACT ON – Physical connection to the Broadband modem on WAN port 1 or 2 is established. OFF – No p
Summary of the content on the page No. 9
XiNCOM Corp. Status and Error conditions are indicated by combinations of LEDs, as shown below: LED Action Condition WAN1 LINK/ACT & 10M/100M LEDs flash alternatively. Firmware Download in progress. WAN1 LINK/ACT & 10M/100M LEDs flash concurrently. MAC address not assigned. WAN1 LINK/ACT & 10M/100M LEDs solid On SDRAM error WAN2 LINK/ACT & 10M/100M LEDs solid On Timer/Interrupt error LAN1 LINK/ACT & 10M/100M LEDs solid On LAN/WAN error Page 7
Summary of the content on the page No. 10
Rear Panel Figure 1: Rear panel of XC-DPG402 shown DC 5V WAN 2 Reset LAN Ports WAN 1 Figure 2: Rear Panel of XC-DPG502 and 602 shown WAN 1 Connect the broadband modem here. If not available contact your ISP. nd WAN 2 Connect the 2 Broadband Modem here, if available. LAN Ports Connect the PCs to these ports. Both 10BaseT and 100BaseT connections can be used simultaneously. Note: Any port will automatically operate as an "Uplink" port if required. Just use a normal LAN cable to connec
Summary of the content on the page No. 11
XiNCOM Corp. TFTP Download This setting can be used to update the firmware on your router when HTTP update in unsuccessful or unavailable: 1. Save your configuration in the router menu “Upgrade Firmware” you can also use the TFTP utility. 2. Power off the router and set DIP switches 3 and 4 down (402 only). 3. Power on the XC-DPG Twin WAN Router. 4. Use the supplied Windows TFTP utility or any other TFTP client program to apply the new firmware. If using the supplied Windows TFTP program
Summary of the content on the page No. 12
XiNCOM Corp. 2: Basic Setup Overview Basic Setup of your XC-DPG Twin WAN Router involves the following steps: 1. Connect the XC-DPG Twin WAN Router to one (1) PC, and configure it for your LAN. 2. Connect your XC-DPG Twin WAN Router to your LAN, and connect the Broadband Modem or Modems. 3. Configure your XC-DPG Twin WAN Router for Internet Access. 4. Configure PCs on your LAN to use the XC-DPG Twin WAN Router. Requirements • One (1) or two (2) DSL or Cable modems, each with an Interne
Summary of the content on the page No. 13
XiNCOM Corp. 7. Enter admin for the "User Name" and leave the "Password" blank. • The "User Name" is always admin • You can and should set a password, using the following Admin Password screen. No Response? • Is your PC using a Fixed IP address? If so, you must configure your PC to use an IP address within the range 192.168.1.2 to 192.168.1.254, with a Network Mask of 255.255.255.0. See Appendix B – Windows TCP/IP Setup for details. • Check that the XC-DPG Twin WAN Router is properly
Summary of the content on the page No. 14
9. Select LAN & DHCP from the menu. You will see a screen like the example below. Figure 6: LAN & DHCP 10. Ensure these settings are suitable for your LAN: • The default settings are suitable for many situations. • See the following table for details of each setting. 11. Save your data, then go to Step 2, installing the XC-DPG Twin WAN Router in your LAN. Settings – LAN & DHCP IP Address IP address for the XC-DPG Twin WAN Router, as seen from the local LAN. Use the default value unless
Summary of the content on the page No. 15
XiNCOM Corp. further details. • Client Lease Time - The time expired which client’ IP address is released and renewed again after. • Client Default DNS – The default DNS which are used by clients, but they can be changed. DHCP IP Address • Offered Range fields set the values used by the DHCP server when Range allocating IP Addresses to DHCP clients. This range also determines the number of DHCP clients supported. • Free Entries indicates how many DHCP entries are not currently all
Summary of the content on the page No. 16
2. Installing the XC-DPG Twin WAN Router in your LAN Figure 7: Installation Diagram 1. Ensure the XC-DPG Twin WAN Router and the DSL/Cable modem are powered OFF. Leave the modem or modems connected to their data line. 2. Connect the Broadband modem or modems to the XC-DPG Twin WAN Router. • If using only one (1) Broadband modem, connect it to the "WAN 1" port. • Use the cable supplied with your DSL/Cable modem. If no cable was supplied, use a standard cable. 3. Use standard LAN cables
Summary of the content on the page No. 17
XiNCOM Corp. • The Error LED will flash during start up, but will then turn Off. If it stays On, there is an error condition. • For each PC connected to the LAN ports, the corresponding LAN LED (either 10 or 100) should be ON. 3. Configuring the XC-DPG Twin WAN Router for Internet Access Select Primary Setup from the menu, to see a screen like the example below. • Configure WAN 1 and/or WAN 2 as required. • For any of the following situations, refer to Chapter 3: Advanced Port Setup fo
Summary of the content on the page No. 18
Settings – Primary Setup Select the appropriate setting: Connection Mode • Enable – Select this if you have connected a broadband modem to this port. • Disable – Select this if there is no broadband modem connected to this port. • Backup – Use this if you have a broadband modem on each port, and wish to normally use only one. Select Enable for the primary port, and Backup for the secondary port. The Backup port will only be used if the primary port fails. Connection Check the data su
Summary of the content on the page No. 19
XiNCOM Corp. Optional • Host name – This is required by some ISPs. If your ISP provided a Host Name, enter it here. Otherwise, you can use the default value. • Domain name – This is required by some ISPs. If your ISP provided a Domain Name, enter it here. Otherwise, you can use the default value. • MAC address – Some ISP's record your PC’s MAC address (also called "Physical address" or "Network Adapter address"). If so, you can enter the MAC address expected by your ISP in this field. Oth
Summary of the content on the page No. 20
4: Configure PCs on your LAN Overview For each PC, the following may need to be configured: • TCP/IP network settings • Internet Access configuration TCP/IP Settings If using the default XC-DPG Twin WAN Router settings, and the default Windows 95/98/ME/2000/XP TCP/IP settings, no changes need to be made. Just start (or restart) your PC. • By default, the XC-DPG Twin WAN Router will act as a DHCP Server, automatically providing a suitable IP Address (and related information) to each PC
