Transition Networks SWITCHABLE ETHERNET AND FAST ETHERNET SSEFE10XX-10X user manual

Summary of the content on the page No. 1

User’s Guide
SSEFE10xx-10x
Stand-Alone Media Converter
• Switchable Ethernet and Fast Ethernet
 10 Mb/s Copper to Fiber
 100 Mb/s Copper to Fiber
Transition Networks SSEFE10xx-10x series
Ethernet / Fast Ethernet media converter is a
10Mbps or 100Mbps switch-selectable media
converter. Both the copper and fiber links operate at the same speed setting via a
hard set with a dip switch, so the media converter operates at either 10 Mb/s
copper to fiber or 100 Mb/s copper to fiber.
Part Number Po

Summary of the content on the page No. 2

SSEFE10xx-10x Installation Installation -- Continued The Link Pass-Through and speed switches are located on the side of the Power the Media Converter media converter. Use a small screwdriver to set the recessed switches. AC 1. Connect the barrel connector on the power adapter to the media Link Pass-Through: up = Enable Set Link Pass-Through (switch 1) converter’s power port (located on the back of the media converter). Speed: up = 100 Mb/s Switch 1 sets the Link Pass-Through feature: 2. C

Summary of the content on the page No. 3

SSEFE10xx-10x Installation -- Continued Operation Install the Fiber Cable Status LEDs The SSEFE10xx-10x is designed to be installed in pairs over the fiber link, Use the status LEDs to monitor the SSEFE10xx-10x media converter operation in where one is the local media converter and the other is the remote. the network. 1. Locate or build fiber-optic cable with male, two-stranded TX to RX PWR Power On = Connection to the external AC or DC power. connectors installed at both ends. F-ACT Fiber

Summary of the content on the page No. 4

SSEFE10xx-10x Cable Specifications Cable Specifications -- Continued The physical characteristics must meet or exceed IEEE 802.3™ specifications. Copper Cable Fiber Cable Category 3: (Minimum requirement for 10 Mb/s operation) Gauge 24 to 22 AWG -9 Bit Error Rate: <10 Attenuation 11.5 dB/100m @ 5-10 MHz Single mode: 9 µm Category 5: (Minimum requirement for 100 Mb/s operation) Gauge 24 to 22 AWG SSEFE1012-100 1310 nm single mode Attenuation 22.0 dB /100m @ 100 MHz Fiber-optic Transmitter

Summary of the content on the page No. 5

SSEFE10xx-10x Technical Specifications Troubleshooting For use with Transition Networks Model SSEFE10xx-10x or equivalent. 1. Is the PWR LED on the media converter illuminated? Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX NO Data Rate: 10 Mb/s, 100 Mb/s  Ensure that the power adapter is the proper type of voltage and cycle frequency for the outlet (See “Power Supply” on page 8.) Dimensions 3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm)  Ensure the power adapter is properly installe

Summary of the content on the page No. 6

SSEFE10xx-10x Troubleshooting -- Continued Contact Us Technical Support 6. Is the TP-ACT LED illuminated? Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 NO  Check the twisted-pair copper cables for proper connection. International: 00-1-952-941-7600  Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600. YES Transition Now  Go to step 7. Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transitio

Summary of the content on the page No. 7

Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi