Summary of the content on the page No. 1
TT™5800X/TT™2400X
Gateway
User Manual
802.11a
802.11b/g
All Rights Reserved. Copyright 2006 Teletronics International, Inc.
2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
Summary of the content on the page No. 2
Table of Contents Disclaimers ………………………….………….….…….……….….………........3 Introduction ……………………………………………………………………….4 Product Features ………………………………………………………………...5 Product Specifications ………………………………………………………….5 Installation ………………………………………………………………..………10 Configuring windows for IP Networking ……………………………………11 Web Configuration Interface …………………………………………………..15 Appendix A: Warranty Policy …………………………………………………..50 Appendix B: RMA Policy ………………………………………………………..51 Appendix C: Regulatory Information ……………
Summary of the content on the page No. 3
Disclaimers No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from the copyright owner. All the other trademarks and registered trademarks are the property of their respective owners. Statement of Conditions We may make improvements or changes in the product described in this documentation at any time. The information regarding to the product in this manua
Summary of the content on the page No. 4
Introduction The TT™5800X gateway is Teletronics’s answer to the ever growing demand for higher bandwidth and security in a wireless network environment. It is based on a brand new redesigned platform that not only offers faster performance and capacity but also the support all current pre IEEE 802.11i wireless security standards. The TT™5800X is the IEEE 802.11a version of the platform that directly targets the need to those that requires the more secure, less crowded 5.8 GHz frequency spectrum
Summary of the content on the page No. 5
Product Features • Compact size for small enterprise or system integrate service market • Compliant with IEEE 802.11a specifications • Supports 64/128-bit WEP, WPA and IEEE802.1x • Supports Atheros Super A (up to 108Mbps) • Intelligent firmware upgrade via Web browser • Built-in Web-based utility for easy configuration from any Web browser • Support POE (IEEE 802.3af) function • Supports wireless bridging and MAC address filtering • Super bright LED indicating status and signal level (RSSI) • Pr
Summary of the content on the page No. 6
• 16dBm (± 2dB) @ 54Mbps • 17dBm (± 2dB) @ 48Mbps Output Power • 18dBm (± 2dB) @ 36Mbps • 19dBm (± 2dB) @ 6 Mbps IEEE 802.11a Sensitivity @ 10% Packet Error Rate • 54Mbps: -70dBm • 48Mbps: -71dBm • 36Mbps: -75dBm Receiver Sensitivity • 24Mbps: -79dBm • 18Mbps: -82dBm • 12Mbps: -84dBm • 9Mbps: -86dBm • 6Mbps: -87dBm IEEE 802.11a (OFDM) • 48/54 Mbps (QAM-64) Modulation • 24/36 Mbps (QAM-16) • 12/18 Mbps (QPSK) • 6/9 Mbps (BPSK) • USA(FCC): 5.15GHz ~ 5.25GHz, 5.25GHz ~ 5.35GHz, 5.47 GHz ~ 5.725 GHz
Summary of the content on the page No. 7
Sensitivity @ 8% Packet Error Rate IEEE 802.11g Sensitivity @10% Packet Error Rate • 54Mbps:-72dBm Receiver Sensitivity • 48Mbps:-73dBm • 36Mbps:-77dBm • 24Mbps:-81dBm • 18Mbps:-84dBm • 12Mbps:-86dBm • 9Mbps:-88dBm • 6Mbps:-89dBm • 11Mbps:-88dBm • 5.5Mbps:-90dBm • 2Mbps:-92dBm • 1Mbps:-95dBm • 11Mbps:-88dBm • 5.5Mbps:-90dBm • 2Mbps:-92dBm • 1Mbps:-95dBm IEEE 802.11b (DSSS) • 5.5/11 Mbps (CCK) • 2 Mbps (DQPSK) • 1 Mbps (DBPSK) IEEE 802.11g (OFDM/DSSS) Modulation • 48/54 Mbps (QAM-64) • 24/36 Mbp
Summary of the content on the page No. 8
Color Status Item Specification ON Power on PWR Red Off No power ** ON Connected OFF RF Not connected Yellow Blinking Connected and transmitting ON Connected OFF Not connected LAN Green Blinking Connected and transmitting ** Blinking left to right Not connected (Scanning for AP) Received Signal Level Red ** ON Connected, indicating RSSI (5 LEDs) * All ON * AP mode. ** SU mode. Software Specification Item Specification Static IP, DHCP Client, PPPoE Client WAN Features MAC Cloning WAN Ping Inboun
Summary of the content on the page No. 9
Item Specification Input Voltage 110-240VAC Line Frequency 50/60Hz Power Output to M/B 48VDC, 1A Environmental Item Specification -20 C to 40 C (-4 F to 104 F), Operating Temperature 10 to 90% (non-condensing) -25 C to 70 C (-13 F to 158 F), Storage Temperature 10 to 90% (non-condensing) Standards / Regulatory Compliance • CE, FCC Product Kit Part Listing 1. TT™5800X 802.11a PCBA or TT™2400X 802.11b/g PCBA (1) 2. IEEE 802.11a o r IEEE 802.11b/g mini-PCI radio card (1) 3. Power over Ethernet Inje
Summary of the content on the page No. 10
Preparation for Installation Always double check for any missing parts from the kit you received before deployment. Next step is to set up the computer Ethernet interface for configuring the TT™5800X/TT™2400X. you’ll need to set the computer Ethernet interface within the same IP range as your TT™5800X/TT™2400X. Check the following section - “Hardware Installation” and the next chapter - “Configuring Windows for IP Networking” to obtain complete details. Hardware Installation Follow the procedure
Summary of the content on the page No. 11
To establish a communication between your PCs and TT™5800X/TT™2400X, you will need to set up a static IP address for your computer first. This section helps you configure the network settings for your operating system. Please follow the procedures below to complete the settings (suppose the default IP address of the unit is 192.168.3.1): Windows 98/Me 1. Click Start on the taskbar and choose Control Panel from the submenu of Settings. 2. Select Network to open the Network dialog box, and then un
Summary of the content on the page No. 12
3. Select the Internet Protocol (TCP/IP) for your network card, and then click Properties to open the Internet Protocol (TCP/IP) Properties dialog box. 4. Under the General tab, choose Use the following IP address, and then specify an IP address. For example, type in 192.168.3.x in the IP Address area and 255.255.255.0 in the Subnet Mask area. Note: Again the IP address must be in the format of 192.168.3.x. Where the value of X should be ranged from 2 to 254. 5. Click OK. All Rights Reserved. Co
Summary of the content on the page No. 13
Windows XP 1. Click Start on the taskbar and choose Network from the submenu of Control Panel. 2. Right-click the Local Area Connection icon and then choose Properties from the menu. You should see the Local Area Connection Properties dialog box shown below. 3. Select the Internet Protocol (TCP/IP) for your network card, and then click Properties. 4. In the opened dialog box, choose Use the following IP address 5. Under the General tab, choose Use the following IP address, and then specify an IP
Summary of the content on the page No. 14
Note: Again the IP address must be in the format of 192.168.3.x. Where the value of X should be ranged from 2 to 254. 6. Click OK. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
Summary of the content on the page No. 15
Web Configuration Interface Note: The configuration and information pages below are based on AP mode web interface; they are also applicable for Subscriber units as well unless they are specified. The Default IP Addresses: Access Point: 192.168.1.1 Subscriber: 192.168.3.1 To access the web control interface please open up a browser window and type in the factory default IP address in the URL. Then press Enter on your keyboard, you will see the login prompt window appear similar like the one show
Summary of the content on the page No. 16
Status Device Information The default status page is Device Information. All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here. You can do DHCP release and renew from this page when DHCP client is enabled. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
Summary of the content on the page No. 17
Wireless Associated Wireless Client List Use this option to view the wireless clients that are connected to your wireless AP gateway. You may need to reload this page to see new changes. Click the button below to reload automatically. The WIRELESS STATUS page on SU interface is slightly different, shows the Available AP list. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
Summary of the content on the page No. 18
Routing Routing Table The routing section displays all of the routing details configured for your router. A value of 0.0.0.0 for gateway means there is no next hop, and the IP address is directly connected to the router on the interface specified: LAN or WAN. A value of 0.0.0.0 in both the destination IP and netmask means that this is the default route. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8
Summary of the content on the page No. 19
Logs System Logs Use this option to view the router logs. You can define what types of events you want to view and the event levels to view. This router also has external syslog server support so you can send the log files to a computer on your network that is running a syslog utility. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
Summary of the content on the page No. 20
Statistics Network Traffic Stats Traffic Statistics displays Receive and Transmit packets passing through your router. It displays all of the LAN and WAN packets transmit and receive statistics. All Rights Reserved. Copyright 2006 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851
