Summary of the content on the page No. 1
ipRocketLink™ Model 3087
Serial G.SHDSL Bridge/Router
Quick Start Guide
Document Number: 03330U7-003 Rev. A Sales Office: +1 (301) 975-1000
Part Number: 07M3087-QS Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
Revised: June 29, 2006
WWW: www.patton.com
Summary of the content on the page No. 2
• This devise contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. WARNING • Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are connected. The mains outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protecte
Summary of the content on the page No. 3
3. Insert the male plug of the AC power cord into an AC power outlet (mains) (100-240 V AC). 1.3 Power-up indication The Power LED blinks as the ipRocketLink is powering up. When the Power LED stops blinking and remains lit, the ipRocketLink is ready for you to configure. 2.0 Configure the IP address The ipRocketLink is shipped with a factory-configured IP address to the Ethernet LAN port (green outline). The IP address is 192.168.200.10/24. In most case
Summary of the content on the page No. 4
10/100 Crossover MDI-X Power Ethernet Interface Port DSL fifififi ip list interfaces IP Interfaces: ID | Name | IP Address | DHCP | Transport ---|------|----------------|----------|-------------- 1 | ip1 | 192.168.200.10 | disabled | ---------------------------------------------------- 2. Modify the IP address for the LAN port according to your network requirements. fifififi ip set interface ip1 ipaddress 10.10.10.5 255.255.25
Summary of the content on the page No. 5
4.0 Log onto the GUI web management page You will now access the web management graphical user interface (GUI) to configure the ipRocketLink using a standard web browser (such as Netscape or Internet Explorer). 1. At your PC, open a web browser and enter the IP address you assigned to the ipRocketLink’s Ethernet LAN port in step 2 of 2.2 “Modify the IP address”. 2. Log into the web management home page using the username superuser and the password
Summary of the content on the page No. 6
Connect the serial cable to the ipRocketLink serial port as follows: 1. Attach the male connector of the serial cable to the female serial connector on the 3087. 2. Attach the other end of the cable to the serial connector on local device’s serial port. Note The 3087’s V.35 interface is wired as a DCE. No DTE configuration is possible. If you are directly con- necting the 3087’s V.35 interface to a third-party equipment that cannot be configured as a D
Summary of the content on the page No. 7
B.0 Appendix—Key factory default parameters Key factory default parameters. Parameter Default Default Default Ethernet port IP address 192.168.200.10 255.255.255.0 - G.SHDSL port 512 kbps Annex B Remote Serial port 512 kbps Internal clock mode - WAN Static IP address type - - DHCP server Disabled - - DHCP relay Disabled - - Security Disabled - - SNTP client Unicast mode - disabled Anycast mode - disabled Broadcast mode - enabled C.0 Compliance Inf
Summary of the content on the page No. 8
C.2 Radio and TV interference (FCC Part 15) This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television recep- tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable pr
Summary of the content on the page No. 9
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/ certifications/. 3.5 FCC Part 68 (ACTA) Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. The method used to connect this equipment to the premises wirin
Summary of the content on the page No. 10
Copyright statement Copyright © 2006, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term ipRocketLink is a trademark of Patton Electronics Company. All other trademarks presented in this doc- ument are the property of their respective owners. Warranty, Trademark, & Compliance Information For warranty, trademark and
