Patton electronic IM1/I user manual

Summary of the content on the page No. 1

USER
MANUA L
MODEL IM 1/I
Ethernet Bridge Module
Part# 07MIM1I-D
SALES OFFICE
Doc# 090101UD
(301) 975-1000
Revised 7/29/99
TECHNICAL SUPPORT
(301) 975-1007
An ISO-9001
http://www.patton.com
Certified Company

Summary of the content on the page No. 2

1.3 SERVICE 1 1..0 0 W WA AR RR RA AN NT TY Y IIN NF FO OR RM MA AT TIIO ON N All warranty and nonwarranty repairs must be returned freight Patton Electronics warrants all Model IM1/I components to be free prepaid and insured to Patton Electronics. All returns must have a from defects, and will—at our option—repair or replace the product Return Materials Authorization number on the outside of the shipping should it fail within one year from the first date of shipment. container. This nu

Summary of the content on the page No. 3

2 2..0 0 G GE EN NE ER RA AL L IIN NF FO OR RM MA AT TIIO ON N 2.3 TYPICAL APPLICATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is The Model IM1/I QuickConnect™ is designed to plug directly into warranted for One Year parts and labor. If any questions or problems the rear of a Patton Electronics baseband modem (i.e. Model 1090 or arise during installation or use of this product, please do not hesitate to 1092

Summary of the content on the page No. 4

3 3..0 0 C CO ON NF FIIG GU UR RA AT TIIO ON N 4 4..0 0 IIN NS ST TA AL LL LA AT TIIO ON N The Model IM1/I is completely plug and play. This section tells you The Model IM1/I module plugs into Patton’s fiber and copper how to make the connections. baseband modems to provide Ethernet LAN extension. The IM1/I has no switches or jumpers and does not need to be configured. However, 4.1 INSTALLING THE QUICKCONNECT™ MODULE factors such as ty type of medium, throughput across the link and clo

Summary of the content on the page No. 5

3.1.2 Installing the New QuickConnect™ Module 4.2 CONNECTING TO THE 10BASE-T ETHERNET PORT 1) Make sure the power switch on the base unit is off. Leave the The RJ-45 Ethernet port on Model IM1/I is designed to connect power cord plugged into a grounded outlet to keep the unit directly to a 10BaseT network. Figure 3, below, shows the 10BaseT grounded. RJ-45 port pin description. You may make connections up to 330 feet using Type 4 or 5 cable. 2) Hold the module with the faceplate toward

Summary of the content on the page No. 6

5.0 OPERATION 4.3 CONNECTION TO THE LINE INTERFACE MEDIA Once the Model IM1/1 is installed, it should operate transparently. Instructions for connecting the line interface media (twisted pair , or This sections describes power-up, general operating instructions, and fiber optic cable) are contained within the base unit user manual. the LED status monitors. Please refer to the base unit manual for connection details. 5.1 OPERATING INSTRUCTIONS Notice! Any terminal cable connected to the Mo

Summary of the content on the page No. 7

A AP PP PE EN ND DIIX X A A 5.3 LED STATUS MONITORS PATTON MODEL IM1/I SPECIFICATIONS The Model IM1/I features two LEDs that monitor general operating status and the 10Base-T twisted pair link integrity. Figure 4 (below) shows the LEDs located directly beneath the RJ-45 jack. Following LAN Connection: RJ-45, 10Base-T, 802.3 Ethernet Figure 4 is a description of each LEDs function. MAC Address Table Size: 4096 entries Quik-Connect Interface Module MAC Address Aging: MAC addresses deleted af

Summary of the content on the page No. 8

Dear Valued Customer, A AP PP PE EN ND DIIX X B B IM1/I INTERFACE PIN ASSIGNMENT Thank you for purchasing Patton Electronics products! We do appreciate your business. I trust that you find this user manual helpful. 10BASE-T Interface Pin Description We manufacture one of the widest selections of data (RJ-45 Female Connector) communications products in the world including CSU/DSU's, network (DTE Configuration) termination units, powered and self-powered short range modems, fiber optic modem