Summary of the content on the page No. 1
Model EHA3201
EnviroNET G.SHDSL Router
Quick Start Guide
Important—This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Sales Office: +1 (301) 975-1000
Part Number: 07MEHA3201-QS, Rev. B
Technical Support: +1 (301) 975-1007
Revised: July 21, 2011 E-mail: support@patton.com
WWW: www.patton.com
Summary of the content on the page No. 2
• Do not open the device when the power cord is connected. For sys- tems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. WARNING • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the device shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker in c
Summary of the content on the page No. 3
Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the follow- ing to prevent ESD: WARNING • Always follow ESD prevention procedures when removing and replac- ing cards. • Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to safely channel unwant
Summary of the content on the page No. 4
1.1 Grounding the EHA3201 Before installing the EnviroNET G.SHDSL Router, it is important to establish a good grounding connection first. 1. Assemble a ground wire using #10 AWG wire with green-and-yellow-colored insulation and two ring ter- minals. Make the wire long enough to reach one of the following earth ground sources: •The building ground rod (generally located at the site’s main service entrance) A sprinkler system pipe A cold-water pipe Building structural steel 2. Install th
Summary of the content on the page No. 5
1 TX+ (data output from the G.SHDSL router) 1 2 TX- (data output from the G.SHDSL router) 2 3 RX+ (data input to the G.SHDSL router) 3 4 (no connection) 4 5 5 (no connection) 6 6 RX- (data input to the G.SHDSL router) 7 7 (no connection) 8 8 (no connection) Figure 3. EnviroNET G.SHDSL Router 10/100Base-T RJ-45 Connector Pinout 1.4 Connecting Power The EHA3201 is an internally powered unit. The power connection is made via the 3-pin power connector on the bottom panel of the EnviroNET G.SHDSL R
Summary of the content on the page No. 6
Note It does not matter whether the positive (+) or negative (-) side of the DC power supply is grounded. However, the polarity on the power source must be matched up properly to the EHA3201 power input (i.e. negative power source terminal to negative power input; positive power source terminal to positive power input). 2.0 Configuring the EHA3201 The EnviroNET G.SHDSL Router comes pre-configured to communicate with other devices on the network. To futher configure the EHA3201, you may log
Summary of the content on the page No. 7
2.2 Configuring applications The EHA3201 is typically used in a bridged or routed application. For instruction on how to configure the EHA3201 for an application, refer to the Model 3201 & 3241 User Manual. Bridged Applications For a bridged application connecting standalone units back-to-back, see pages 29-32 in the Model 3201 & 3241 User Manual. For a bridged application connecting the CPE to a DSLAM, see pages 38-46 in the Model 3201 & 3241 User Manual. Routed Applications For a ro
Summary of the content on the page No. 8
B.0 EHA Case Specifications B.1 Power Requirements UAC: 110, 220VAC, 2.25W B.2 Temperature Range -40–185°F (-40–85°C) B.3 Humidity Up to 90% non-condensing. B.4 Dimensions 8”H x 9.25”W x 3.25”D B.5 Weight 6.4lb (2.9kg) Note For Model 3201 unit specifications, refer to the Model 3201 & 3241 User Manual located on the CD- ROM shipped with your EHA3201 and available online at www.patton.com/manuals. 8 EHA3201 Quick Start Guide
Summary of the content on the page No. 9
C.0 Compliance Information C.1 Compliance EMC: FCC Part 15, Class A EN55022, Class A EN55024 Safety: UL 60950-1/CSA C22.2 N0. 60950-1 IEC/EN60950-1 AS/NZS 60950-1 PSTN Regulatory: FCC Part 68 CS-03 AS/ACIF S043:2003 C.2 FCC Part 68 (ACTA) Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX. I
Summary of the content on the page No. 10
3.3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con- firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra- tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. This Declaration of Conformity means that the equipment meets
Summary of the content on the page No. 11
C.5 EC Declaration of Conformity Product Description: Models 3201 & 3241 We certify that the apparatus identified above conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip- ment and the mutual recognition of their conformity. The safety advises in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on th
Summary of the content on the page No. 12
Copyright statement Copyright © 2011, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term EnviroNET is a trademark of Patton Electronics Company. All other trademarks presented in this docu- ment are the property of their respective owners. Warranty, Trademark, & Compliance Information For warranty, trademark and co
Summary of the content on the page No. 13
D.0 Buccaneer 400 Series Environmentally Sealed Connectors The following instructions are provided by Bulgin UK for assembling the 400 Series Buccaneer IP68 Sealed Electrical Cable Connectors. IMPORTANT EHA3201 Quick Start Guide 13
Summary of the content on the page No. 14
14 EHA3201 Quick Start Guide
Summary of the content on the page No. 15
EHA3201 Quick Start Guide 15
Summary of the content on the page No. 16
16 EHA3201 Quick Start Guide
