Summary of the content on the page No. 1
DiamondLink™ Model 3201 & 3241
G.SHDSL Router
Quick Start Guide
Important—This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Document Number: 03321U7-001 Rev. B Sales Office: +1 (301) 975-1000
Part Number: 07M3201-QS Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
Revised: October 15, 2008
WWW: www.patton.com
Summary of the content on the page No. 2
• This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. WARNING • The external power adapter shall be a listed Limited Power Source. The mains outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker. • If an AC power adapter is used, ensure that the power cabl
Summary of the content on the page No. 3
Terminal block (-) Terminal (+) Terminal Figure 1. 48VDC power supply 1.2 Models with external DC power supply 1. Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to the 48VDC power supply terminal block (see figure 1). 2. Connect the negative (-) terminal from the power source with to the negative (-) terminal on the power supply. 3. Connect the positive (+) terminal from the power source with to the positive (+)
Summary of the content on the page No. 4
2.1 Connect a PC and log in 1. Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port to the on the DiamondLink’s (red) Console port (see figure 2). PC with terminal emulator Serial port Connect to Console port (red port) Figure 2. Connecting DiamondLink to the PC’s serial port 2. Start a HyperTerminal session on the PC using the settings: 9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
Summary of the content on the page No. 5
3.0 Connect to the local IP network Now you can connect the DiamondLink to your local IP network and complete the remaining configuration from your PC using a standard web browser. Connect the DiamondLink’s (green) Ethernet port to the same Ethernet segment as your PC (see figure 3). Press the MDI-X switch until the Ethernet Link LED turns on. Connect to Ethernet port (green port) PC MDI-X switch Ethernet port Figure 3. Connecting the DiamondLink to the local IP n
Summary of the content on the page No. 6
5.0 Connect the G.SHDSL port 1. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end. 2. Plug one end of the cable into the RJ-11socket (yellow colored port labeled LINE) on the DiamondLink Router. 3. Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service. 4. When a DSL link is established, the front panel WAN Link LED will turn on. 6.0 Additional Information Refer to the Diamon
Summary of the content on the page No. 7
B.0 Compliance Information B.1 Compliance EMC: • FCC Part 15, Class A • EN55022, Class A • EN55024 Safety: • UL 60950-1/CSA C22.2 N0. 60950-1 • IEC/EN60950-1 • AS/NZS 60950-1 PSTN Regulatory: • FCC Part 68 • CS-03 • AS/ACIF S043:2003 B.2 FCC Part 68 (ACTA) Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the
Summary of the content on the page No. 8
2.3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con- firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra- tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. This Declaration of Conformity means that the equipme
Summary of the content on the page No. 9
B.6 Authorized European Representative D R M Green European Compliance Services Limited. Avalon House, Marcham Road Abingdon, Oxon OX14 1UD, UK DiamondLink 3201 & 3241 Quick Start Guide 9
Summary of the content on the page No. 10
Copyright statement Copyright © 2008, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term DiamondLink is a trademark of Patton Electronics Company. All other trademarks presented in this doc- ument are the property of their respective owners. Warranty, Trademark, & Compliance Information For warranty, trademark and
Summary of the content on the page No. 11
DiamondLink 3201 & 3241 Quick Start Guide 11
Summary of the content on the page No. 12
12 DiamondLink 3201 & 3241 Quick Start Guide
