Summary of the content on the page No. 1
TM
Hotwire 5216 Remote Termination Unit (RTU)
Customer Premises
Installation Instructions
Document Number 5216-A2-GN10-10
February 1998
Before You Begin
An optional POTS (Plain Old Telephone Service) splitter is available for the 5216 RTU.
When a POTS splitter is installed, the telephone and 5216 RADSL (Rate Adaptive
Digital Subscriber Line) RTU can function at the same time over the same pair of
copper wires. In order to confirm the RTU installation, the POTS splitter should be
installed first.
Summary of the content on the page No. 2
Package Checklist Verify that your package contains the following: Model 5216 Remote Termination Unit (RTU) DSL interface cable with RJ11 modular plugs Power cord with power transformer Two ferrite chokes Warranty card Refer to Cables & Connectors, page 13, for standard pin numbers. What Does the Hotwire RTU Do? The 5216 RTU is a component in the DSL Access System. This system provides high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring. DS
Summary of the content on the page No. 3
When a POTS splitter is used at both ends of the local loop, wiring is connected: From the demarcation point to the CP POTS splitter, and From the demarcation point to the DSL jack. Customer Premises (CP) Demarcation Point CP POTS POTS Splitter Central Office (CO) DSL RTU Jack DSL Local Loop Network Ethernet Service Crossover Provider Cable Punchdown (NSP) Block or NID End-user System 97-15608 DSL - Digital Subscriber Line POTS - Plain Old Telephone Service NID - Network Interface Device RTU
Summary of the content on the page No. 4
DSL Access without a POTS Splitter When the 5216 RTU is installed without a POTS splitter, a second telephone wiring pair is needed for DSL access. Customer Premises (CP) Demarcation Point POTS Central Office (CO) DSL RTU Jack DSL Local Loop Ethernet Network Crossover Service Cable Provider Punchdown (NSP) Block or NID End-user System 97-15609 DSL - Digital Subscriber Line POTS - Plain Old Telephone Service NID - Network Interface Device RTU - Remote Termination Unit New Wiring Connections Exist
Summary of the content on the page No. 5
Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. Typically, the punchdown block is installed in commercial locations and the NID is installed in residential locations. Procedure 1. Access the punchdown block or NID. Disconnect the DSL access pair from the local loop. ! WARNING: Do not continue unless the DSL access line from the local loop has bee
Summary of the content on the page No. 6
Green (T1) and red (R1) are the standard wiring colors used in the next two illustrations. In the following example, a NID is used without a POTS splitter. It includes an existing POTS line and a second pair installed for DSL access. The POTS pair for the existing POTS line wiring does not need to be disconnected unless a POTS splitter is going to be installed. Telephone Network Interface Device (NID) Customer Premises Demarcation Point Tip T1 (Green) DSL Pair POTS Pair Ring R1 (Red) DSL/POTS Ac
Summary of the content on the page No. 7
2. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. Tighten both terminal screws with a flat-blade screwdriver. Telephone Network Interface Device (NID) Customer Premises Demarcation Point Tip T1 (Green) DSL Pair POTS Pair Ring R1 (Red) Wiring to DSL Jack DSL/POTS Access from Existing POTS Local Loop Ground Wiring to 97-15438-01 Telephone 7
Summary of the content on the page No. 8
DSL Jack Installation The 5216 RTU connects to the local loop via wiring from the demarcation point to an RJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ11 jack or replace a single jack with a double RJ11 jack. The RJ11 6-pin jack uses the center two pins. For pin assignments, refer to Cables & Connectors, page 13. Customer Premises Demarcation Point DSL Twisted-pair Wiring DSL Central
Summary of the content on the page No. 9
POWER ETHERNET POWER ETHERNET DSL DSL Installing the RTU Place the 5216 RTU on a flat surface with clearance for the rear connectors. Procedure 1. Use the RJ11 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL. Hotwire RTU DSL Jack 97-15300-01 2. Use an 8-pin Ethernet crossover cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET. Connect the other end to a PC w
Summary of the content on the page No. 10
POWER ETHERNET DSL POWER DSL ETHERNET 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown. 496-14952 4. Close the two halves Hotwire RTU around the cable and snap the ferrite choke Ethernet shut. Press down on the Line plastic latch to secure the ferrite choke in place around the cable. Ferrite Choke 97-15303c 5. Insert the power cord’s round end into the jack labeled P
Summary of the content on the page No. 11
6. Close the two halves around the cable and snap the ferrite choke shut. Press down on the plastic latch to secure the ferrite choke in place around the cable. 7. Plug the transformer into an AC outlet. The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test. Power-On When power is applied, the RTU performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test. During the power-on self-test,
Summary of the content on the page No. 12
LED Condition Status DSL Blinking RTU is establishing the DSL link. The LED blinks on and off about five times per second. ON The DSL link is now active and ready to transmit and receive data. OFF The DSL link has not been established. ETHERNET ON The Ethernet 10BaseT connection to the end-user system is active. OFF No Ethernet 10BaseT device is detected. Firmware Download The firmware download feature is available via the DSL link or the Ethernet port. During a firmware download, the following
Summary of the content on the page No. 13
LED Symptom Action DSL and Ethernet The DSL link and the Ethernet link have been established. If LEDs are on and the problem continues, contact the NSP. there is no data transmission. Ethernet LED is off. Verify that the Ethernet 10BaseT cable is securely installed at both ends, and that a PC is connected and powered on. Verify that the correct crossover cable is installed. Refer to Cables & Connectors, page 13. PWR LED is off. Check that the power cord is securely installed on both ends. If no
Summary of the content on the page No. 14
The Ethernet interface crossover cable connector uses an 8-pin, non-keyed modular plug. Ethern et Cable 8-Pin Plug Pin #8 Pin #1 97-15305 8-Pin Ethern et Cros s o v er Cable Func tion Pin # Pin # Func tion 10BaseT TX D+ 1 1 10BaseT TX D+ 10BaseT TX D 2 2 10BaseT TX D 10BaseT RX D+ 3 3 10BaseT RX D+ Not Used 4 4 Not Used Not Used 5 5 Not Used 10BaseT RX D 6 6 10BaseT RX D Not Used 7 7 Not Used Not Used 8 8 Not Used 97-15316 14
Summary of the content on the page No. 15
Model 5216 RTU Technical Specifications * Item Specification Height x Width x Depth 1.35″ x 6.00″ x 8.75″ (3.43 cm x 15.35 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Input: 100 Vac, 50 Hz; 120 Vac, 60 Hz; or 230 Vac, 50/60 Hz Class 2 Transformer normal service input voltage range Output: 15 Vdc nominal (+10%), minimum 0.6A Approvals FCC Part 15 Class B Subpart B digital device CISPR 22 Class B Safety Certifications Refer to equipment’s label for approvals on product. Physical Environment
Summary of the content on the page No. 16
Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4. Do not attempt to service this pro
Summary of the content on the page No. 17
CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the member states relating to electrical equipment designed for use within states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive 93/68/EEC. Directive 89/336/EEC – Council Directive of 3 May
Summary of the content on the page No. 18
Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: Trade Name: Hotwire Model Number: 5216-A2-200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference receive
Summary of the content on the page No. 19
EMI Warnings ! WARNING: To Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada. Notice to Users of the Canadian Telephone Network The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, opera
Summary of the content on the page No. 20
Warranty, Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Via the Internet: Visit the Paradyne World Wide Web site at: http://www.paradyne.com Via Telephone: Call our automated call system to r
