Summary of the content on the page No. 1
Model RF500S
Broadband Router
User Guide
Summary of the content on the page No. 2
User Guide Broadband Router Model RF500S PN S000125D Revision D Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2001by Multi Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the content hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-T
Summary of the content on the page No. 3
Table of Contents Contents Contents ...................................................................................................................... 3 Chapter 1 - Introduction ............................................................................................. 6 RF500S Front Panel................................................................................................... 7 Back Panel ...........................................................................................
Summary of the content on the page No. 4
Table of Contents Save Settings to File................................................................................................. 99 Load Settings.......................................................................................................... 100 Upgrade Firmware.................................................................................................. 101 General Diagnostic .................................................................................................
Summary of the content on the page No. 5
Chapter 1 Introduction RouteFinder RF500S User Guide 5
Summary of the content on the page No. 6
Chapter 1 – Introduction Chapter 1 - Introduction Welcome to the world of broadband connectivity to the Internet. The Multi-Tech Broadband RouteFinder connects a cable modem or DSL modem to an Ethernet LAN to provide high-speed broadband access to the Internet for up to 253 users. The Broadband Router features a built-in 4-port 10/100M bps switch, one asynchronous port for backup Internet access or dial-in remote access, firewall services, and network security. This product is ideal for any bus
Summary of the content on the page No. 7
Chapter 1 – Introduction RF500S Front Panel LAN LEDs Link/ACT Lights when the LAN client is correctly connected to the Ethernet port. Blinks when the LAN client is correctly connected to the Ethernet port. 100 Lights when the LAN client is connected at 100MB. Off when the LAN client is connected at 10MB. FDX/COL Lights when the LAN client is connected as full duplex. Off when the LAN client is connected as half duplex. Blinks when there are collisions on the network. Serial LEDs Data Blinks when
Summary of the content on the page No. 8
Chapter 1 – Introduction Back Panel Power 5VDC Connect one end of the power cord to power socket and the other end to the power outlet. 10 BT WAN The WAN port is used to connect the router to a DSL or Cable modem. ASYNC The Serial async port connects the router to a standard modem (optional). Reset The Reset button is used to reset the router to factory defaults. 10/100 BT LAN The 4-10/100 ports are used to connect the router to LAN client workstations. If the RF500S is set to use the Uplink fea
Summary of the content on the page No. 9
Chapter 1 – Introduction Application Examples The following examples provide information about RF500S typical applications. The three examples include: 1. Connecting a local LAN to Internet. 2. Connecting a local LAN to the Internet and setting up a remote site. 3. Setting up a LAN to LAN via the Async Port. Example 1 – Connecting a Local LAN to the Internet RouteFinder RF500S User Guide 9
Summary of the content on the page No. 10
Chapter 1 – Introduction Example 2 – Local LAN to Internet / Remote Site RouteFinder RF500S User Guide 10
Summary of the content on the page No. 11
Chapter 1 – Introduction Example 3 – LAN to LAN via an Async Port Note: Set the modem type to leased line. RouteFinder RF500S User Guide 11
Summary of the content on the page No. 12
Chapter 1 – Introduction Setup for Example 3 The setup describes the RF500S used as routers to route IP traffic between two LANs. Network Addresses LAN A IP Network Address: 192.168.2.x WAN IP Network Address: 10.10.10.x LAN B IP Network Address: 192.168.100.x Note: Between LAN A and LAN B Are Two RF500S RouteFinders and One 56K LAN A RF500S WAN Ethernet port in this case is not used 95/98 Workstation has IP Address: 192.168.2.2 RF500S 10/100 Ethernet port has IP Address: 192.168.2.1 RS232 WAN p
Summary of the content on the page No. 13
Chapter 1 – Introduction Check Assign Remote Site an IP Address and enter the IP Address: 192.168.100.2 Check Allow Remote Dial-in Click the Remote Authentication Settings button if you want to authenticate with user name and password. The Remote Connection Authentication screen displays. Remote Connection Authentication Screen If you check PAP, then check Use Local Settings and enter the Remote User Name and Remote Password. Click the OK button and return to the RouteFinder Manager main menu. 4
Summary of the content on the page No. 14
Chapter 1 – Introduction Check Assign Remote Site an IP Address and enter the IP Address: 192.168.100.1 Check Allow Remote Dial-in Click the Remote Authentication Settings button if you want to authenticate with user name and password. The Remote Connection Authentication screen displays. Remote Connection Authentication Screen If you check PAP, then check Use Local Settings and enter the Remote User Name and Remote Password. Click the OK button and return to the RouteFinder Manager main menu. 4
Summary of the content on the page No. 15
Chapter 1 – Introduction Specifications Hardware ARM RISC CPU32 bit, 40MHZ 4MB DRAM and 512k Flash ROM UART Serial port controller LAN Ports Number of Ports: 4 Interface: 10Base T/100BaseTX, - One port can be used for uplink Standard: 802.3 WAN Ports 1 x 10BaseT 1 x RS232 (V.24) DTE Speed: Up to 460K asynchronous Protocols Security: PAP/CHAP, MSCHAP, NAT Firewall, RADIUS and Callback for remote access. Network: TCP/IP, IPX, DHCP, PPP, PPPoE Filtering: Protocol, port number, URL address and IP ad
Summary of the content on the page No. 16
Chapter 2 Hardware Installation RouteFinder RF500S User Guide 16
Summary of the content on the page No. 17
Chapter 2 – Hardware Installation Chapter 2 - Hardware Installation Safety 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in a wet location unless the jack is specifically designed for wet locations. 3. This product is to be used with UL and cUL listed computers. 4. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 5. Avoid using a telephone during an electrical storm. There
Summary of the content on the page No. 18
Chapter 2 – Hardware Installation Cabling Cabling your RouteFinder requires making the appropriate connections to PCs, Cable or DSL modem, analog modem or ISDN TA (optional), AC power, and the RouteFinder. Then, after your device is properly cabled, you will have to configure your RouteFinder. Follow the instructions provided in the Web Browser Configuration and Management chapter. RouteFinder RF500S User Guide 18
Summary of the content on the page No. 19
Chapter 2 – Hardware Installation Cabling Directions Before beginning, turn the power off on all network devices (PCs, Cable/xDSL modems, analog modems, ISDN TAs, and the router). 1. Connect the Ethernet port of each PC or network device to one of the 4 LAN ports. Important: If you are using the Uplink option, Port Number 1 cannot be used as a LAN port). 2. If you are using an analog modem, connect it to the Serial Async port. 3. If you are using the Uplink option to connect to another network s
Summary of the content on the page No. 20
Chapter 3 Web Browser Configuration And Management RouteFinder RF500S User Guide 20
