Summary of the content on the page No. 1
Summary of the content on the page No. 2
Vigor2800 Series Quick Start Guide Copyright Information Copyright Copyright 2005 All rights reserved. This publication contains Declarations information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: • Microsoft is a registered trademark of Microsoft Corp.
Summary of the content on the page No. 3
components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or
Summary of the content on the page No. 4
European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2800 Series ADSL2/2+ Routers DrayTek Corp. declares that Vigor2800 series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 89/336/EEC by comp
Summary of the content on the page No. 5
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful in
Summary of the content on the page No. 6
Table of Contents 1 1. Introduction……………………………………….………………….……………. 1.1 Brief Overview…………………………………………………………..……… 2 1.2 Specifications………………………………………………………..…………. 3 1.3 Front Panel LEDs and Rear Panel Interfaces………………..……….…… 5 1.4 Package Contains……………………………………….…………..…………. 9 10 2. Quick Install Your Vigor2800 Series Router…………………..…….. 2.1 Hardware Installation……………………………….……………..………….. 10 2.2 Configure Your Router via Quick Start Wizard…….……………..………. 11 14 3. Wireless LAN Settin
Summary of the content on the page No. 7
1. Introduction Highlights Easy Internet-sharing of your broadband connection Robust firewall to help protect your network from external attacks For G models: ® Wireless LAN with data rate up to 108Mbps using Super G technology Secure connection with advanced WPA2 encryption and authentication Model comparison chart: High Speed ADSL2/2+ Router ISDN Wireless AP * Vigor2800Gi * * Vigor2800G * * - Vigor2800i * - * * Vigor2800 - - 1
Summary of the content on the page No. 8
1.1 Brief Overview Targeting requirement for residential, SOHO (Small Office and Home Office) and business users, the Vigor2800 series are ADSL2/2+ enabled integrated access device. With downstream speed up to 12Mbps (ADSL2) or 24Mbps (ADSL2+), the Vigor2800 series provide exceptional bandwidth* for Internet access. (*note: the available bandwidth also depends on the Internet Service Provider) Embedded with sophistic VPN firewall security features, the Vigor2800 series provide 32 de
Summary of the content on the page No. 9
1.2 Specifications For Vigor2800 G models TM Wireless Access Point Super G IEEE802.11b/g compliant Up to 108 Mbps data rate ** 64/128-bit WEP Utilizing adaptive radio to WPA/WPA2(IEEE802.11i) automatically identify clear 802.1x authentication with channels RADIUS client Real-time hardware data VPN over WLAN compression TM Wireless client list Fast Frames and Hidden SSID standards-compliant bursting MAC address access control Access point discovery * *Actual dat
Summary of the content on the page No. 10
VPN Network Features Up to 32 VPN tunnels DHCP client/relay/server Supported protocol: PPTP, Dynamic DNS IPSec, L2TP, L2TP over IPSec SNTP client DHCP over IPSec(*) Call scheduling Encryption: AES, MPPE and RADIUS client hardware-based DES/3DES DNS cache/proxy Authentication: MD5, SHA-1 UPnP IKE authentication: pre-shared Routing protocol: key and digital signature(X.509)* Static routing LAN-to-LAN, Teleworker-to-LAN RIP V2 Firewall Facilities Router Management
Summary of the content on the page No. 11
1.3 Front Panel LEDs and Rear Panel Interfaces 1.3.1 Vigor2800Gi LED Status Explanation ACT (Activity) blinking The router is powered on and running properly. ISDN on The ISDN network is correctly setup. blinking A successful remote connection on the ISDN BRI B1/B2 channel. on The P2P function is active P2P blinking When starting to prohibit P2P data Firewall on The DoS function is enabled. blinking When encountered DoS attacks. WLAN on The wireless LAN function is enabled.
Summary of the content on the page No. 12
1.3.2 Vigor2800G LED Status Explanation ACT (Activity) blinking The router is powered on and running properly. QoS on The QoS function is active. P2P on The P2P function is active blinking When starting to prohibit P2P data Firewall on The DoS function is enabled. blinking When encountered DoS attacks. WLAN on The Wireless LAN function is enabled. blinking Ethernet packets are transmitting over wireless LAN. DSL on The ADSL,ADSL2/2+ line is showtime. Printer on The USB interfa
Summary of the content on the page No. 13
1.3.3 Vigor2800i LED Status Explanation ACT (Activity) blinking The router is powered on and running properly. ISDN on The ISDN network is correctly setup. blinking A successful remote connection on the ISDN BRI B1/B2 channel. P2P on The P2P function is active blinking When starting to prohibit P2P data Firewall on The DoS function is enabled. blinking When encountered DoS attacks. VPN on The VPN tunnel is launched. DSL on The ADSL,ADSL2/2+ line is showtime. Printer on The US
Summary of the content on the page No. 14
1.3.4 Vigor2800 LED Status Explanation ACT (Activity) blinking The router is powered on and running properly. QoS on The QoS function is active. P2P on The P2P function is active blinking When starting to prohibit P2P data Firewall on The DoS function is enabled. blinking When encountered DoS attacks. VPN on The VPN function is active. DSL on The ADSL,ADSL2/2+ line is showtime. Printer on The USB interface printer is ready. LAN orange A normal 10Mbps connection is through it
Summary of the content on the page No. 15
1.4 Package Contains Quick Start Guide CD UK-type power adapter EU-type power adapter USA/Taiwan-type power AU/NZ-type power adapter adapter RJ-45 to RJ-45 (ISDN) for RJ-45 Cable (Ethernet) Vigor2800 i models or RJ-11 Cable (Annex A / B) RJ-11 to RJ-45 (Annex B) RJ-11 Cable (PSTN line) Antennas for V2800 G models 9
Summary of the content on the page No. 16
2. Quick Install Your Vigor2800 Series Router 2.1 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. 1. Connect the DSL interface to the external ADSL splitter with an ADSL line cable. 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. 3. For G models, connect detachable antennas to the router. 4. Connect the attached power adapter to the power port. 5. Check the ACT and WAN, LAN LEDs to assure network
Summary of the content on the page No. 17
2.2 Configure Your Router via Quick Start Wizard Introduction The Quick Start Wizard is designed for you to easily set up your broadband Internet access. You can directly access the Quick Start Wizard via Web Configurator. Configure Your Router via Quick Start Wizard First make sure your PC connects to router correctly. You may either Step 1. simply set up your PC to dynamic get IP from router or set up the IP address of PC to be the same subnet as the default IP address of Vigor
Summary of the content on the page No. 18
Now Quick Start Wizard is switched on. Enter login password. Then Step 3. click Next to continue. Select the appropriate Internet access type according to the information Step 4 from your ISP. Or Clicking “Auto detect” button also offers the related DSL parameters automatically. If PPPoE/PPPoA is selected, please manually enter the Step 5 Username/Password provided by your ISP service provider. Checking the Always On means Internet access is always on regardless of Internet us
Summary of the content on the page No. 19
Review the summary of settings. Step 6 On the bottom of Web Configurator window, you can find messages showing the system interaction with you. “Ready” indicates the system is ready for you to input settings. “Settings Saved” means your settings are saved once you click “Finish” or “OK” button. 13
Summary of the content on the page No. 20
3. Wireless LAN Settings(for G models) Select from the menu of the Wireless LAN: Wireless LAN >> General Settings Security Access Control WDS Settings Access Point Discovery Station List (The default value of Frequency Domain was set by factory depends on the reselling region.) Wireless Distribution System Wireless Distribution System(WDS) is an advanced technology to link 2 LANs or 2 WLANs through air, if router is set in Bridge Mode, or to extend a Wireless
