Summary of the content on the page No. 1
INDEX
Symbols F4 OAM
overview 4
A ILMI
address-family ipv4 command disabling 43, 44
for BFD 62, 63 enabling 41, 42
ais-shut command 386 overview 4
aps group command 93, 385 optional parameters
aps submode configuring 8
channel command 93, 94, 385 prerequisites 2
interface loopback command 385 VC class-mapping
See aps group command overview 3
area command (BFD) 60 verifying connectivity 21
atm address-registration command 42 verifying ILMI configuration 43, 45
atm ilmi-config disable command 44
Summary of the content on the page No. 2
Index prerequisites 54 clear bfd counters packet command 67 setting the BFD multiplier 58 clear flow exporter command 259 setting the minimum interval 58, 60 clear flow monitor command 259 setting the multiplier 60 clock source command 176, 182, 322, 380, 387, specifying a VPN VRF instance 62 401, 421, 422, 427, 433, 436 static routes command summary configuring 62 FPD commands (table) 152 bfd command 64, 65 commit command 399 bfd fast-detect command 59, 60 configure command 398 bfd minimum-in
Summary of the content on the page No. 3
Index setting the frame type 422 displaying Ethernet interfaces 137 using the clock source command 422 displaying MAC accounting statistics 142 using the controller e1 command 445 enabling flow-control 136 using the framing command 422, 440 enabling Layer 2 transport mode 143 using the national bits command 422, 440 Gigabit Ethernet standards 130 E3 controller IEEE 802.3 Physical Ethernet Infrastructure configuration prerequisites 420 130 configuring 424 IEEE 802.3ab 1000BASE-T Gigabit Ether-
Summary of the content on the page No. 4
Index using the dot1q native vlan command 468 field-programmable gate array using the dot1q vlan command 466 see FPGA using the interface command 468 flow command 258 using the l2protocol command 471 flow exporter map configuration submode 245 using the show vlan interfaces command flow exporter map version configuration submode 467 246 using the show VLAN trunks command 467 flow exporter-map command 251 Ethernet interfaces flow monitor map configuration submode 246 using the mac accounting co
Summary of the content on the page No. 5
Index frame-relay lmi-type command 165, 172 interface Bundle-Ether command 198, 202 framing command 381, 421, 422, 427, 434, 436, interface Bundle-POS command 196 440 interface command 135, 468 H ATM interface configuration mode 12, 17, 23, HDLC 24, 26, 30, 37, 39, 40, 44, 289, 366 on POS interfaces 272 ATM subinterface configuration mode 20 hw-module node reload command 399 Fast Ethernet 232 hw-module port command 398, 399 for Ethernet interfaces 141, 470 hw-module subslot cardtype command fo
Summary of the content on the page No. 6
Index Fast Ethernet 232 loopback command 381 loopback 220 M on ATM subinterfaces 12, 20 mac accounting command 141 on serial interfaces 353 mac address command 128, 136 POS preconfigure 337 mac-accounting command 128 SONET APS 385, 386 management ethernet interface, configuring 230 SRP 178, 183, 324, 401 match mpls experimental topmost command 406 ipv4 unreachables command 222 match precedence command 406 K mdl string command 434 keepalive command 386 mdl transmit command 421, 434 on POS inter
Summary of the content on the page No. 7
Index sampler map 244 class command 407 sampler map configuration submode 247 police command 407 Network Control Protocols (NCPs) 273, 347 policy-map command 406 no interface command 472 priority command 407 no shutdown command 386 set cos command 407 (warning) 336 policy-map command 406 bundle-POS 199, 204, 206, 211 POS (Packet-over-SONET) Fast Ethernet 232 See POS 269 for Ethernet interfaces 136 pos crc command 386 for Fast Ethernet interfaces 139 on POS interfaces 87, 280 SRP 401 POS interf
Summary of the content on the page No. 8
Index MS-CHAP 301, 302, 303, 304, 309 record ipv4 command 255 overview 300 reload spa PAP 301, 302, 303, 304, 305, 306 after FPD upgrade 152 POS configuration example 327 remote-as command (BFD) 58 prerequisites 300 rings (outer and inner) 396 serial configuration example 328 router bgp command 58 CHAP (Challenge Handshake Authentication router ospf command (BFD) 60 Protocol) 347 router static command (BFD) 62 displaying PPP interfaces 314 RP, preconfiguration directory 333 MS-CHAP (Microsoft
Summary of the content on the page No. 9
Index show bundle Bundle-Ether command 201, 208 delay trigger command 380, 389 show bundle Bundle-POS command 212 framing command 381 show controller sonet command 383 loopback command 381 show controllers command 436, 439 overhead command 381 for the E3 controller 426, 428 path command 382, 389 for the T3 controller 430, 432, 434 path scrambling command 386 show flow exporter-map command 252 See controller sonet command show flow monitor map command 257 source command 251 show fpd package com
Summary of the content on the page No. 10
Index T1 configuration mode 177, 182, 322, 436 U using the channel-group command 177, 182, upgrade hw-module fpd command 152, 153, 158 322, 437 V using the clock source command 422, 436 vc-class using the controller t1 command 177, 182, 322, configuring 48 436, 445 creating 48 using the fdl ansi command 422, 437 on ATM interfaces 34 using the framing command 422, 436 ATM interface using the show controllers command 436 attaching a vc-class 36 using the speed command 437 on ATM PVCs 39 using th
Summary of the content on the page No. 11
Index using the show vlan interfaces command 467 using the show VLAN trunks command 467 vp-tunnel configuring 16 creating 16 on ATM interfaces 47 vp-tunnel command on ATM interfaces 17 vrf command (BFD) 62 W wait-to-restore (WTR) 402 wavelength division multiplexing (WDM) 396 Y yellow command 422, 436 Cisco IOS XR Interface and Hardware Component Configuration Guide OL-14352-01 HC-487
Summary of the content on the page No. 12
Index Cisco IOS XR Interface and Hardware Component Configuration Guide HC-488 OL-14352-01
