Summary of the content on the page No. 1
Cisco 7206 Router Quick Start Guide
1 Documentation and Resources
2 Prepare for Installation
3 Rack-Mount the Router
4 Connect the Router to the Network
5 Start and Configure the Router
6 After Installation
7 Technical Assistance
Summary of the content on the page No. 2
1 Documentation and Resources This section contains information to help you prepare for installing the Cisco 7206 router. I contains a list of online documentation and resources. Document Revision History The Document Revision History below, records technical changes to this document. Table 1 Document Revision History Document Version Date Notes 78-12771-04 March, 2006 Adding documentation survey information. Documentation Survey Is Cisco documentation helpful? Click here or go to http://foru
Summary of the content on the page No. 3
Port Adapter Documentation � Cisco 7200 Series Port Adapter Hardware Configuration Guidelines—DOC-783471= (This document provides bandwidth point information for Cisco 7200 series routers and port adapters.) http://www.cisco.com/univercd/cc/td/doc/product/core/7206/port_adp/config/index.htm � Port adapter documentation—See the document that ships with the port adapter for the customer order number. Port adapter documentation is online at: http://www.cisco.com/univercd/cc/td/doc/product/core/720
Summary of the content on the page No. 4
Ordering Documentation Cisco documentation is available in the following ways: � Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace: http://www.cisco.com/cgi-bin/order/order_root.pl � Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store: http://www.cisco.com/go/subscription � Nonregistered Cisco.com users can order documentation through a local account representative by
Summary of the content on the page No. 5
2 Prepare for Installation Warning Only trained and qualified personnel should install, replace, or service this equipment. Warning Read the installation instructions before you connect the system to its power source. Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible
Summary of the content on the page No. 6
� Port adapter documentation for configuring the interfaces � T1 channel service unit/data service unit (CSU/DSU) that converts the High-Level Data Link Control (HDLC) synchronous serial data stream into a T1 data stream with the correct framing and ones density to connect a serial port to a T1 network. (Some telephone systems require a minimum number of 1 bits per time unit in a data stream, called ones density.) Several T1 CSU/DSU devices are available as additional equipment, and most prov
Summary of the content on the page No. 7
5 3 1 3 Rack-Mount the Router 3 1 2 1 Rack-mount bracket 3 M4 x 8-mm Phillips flathead screws Cable-management bracket 2 Brackets Front-Mounted—Chassis Protrudes from the Rack Locate the rack-mount and cable-management brackets and screws (1, 2, 3 in the illustration above) and a Number 2 Phillips screwdriver. 1. Align the rack-mount bracket (1)—as shown above—to the side of the router. Insert and tighten the screws (3) if you are not adding the cable-management brackets. Repeat this step on
Summary of the content on the page No. 8
5 3 1 3 2 1 Cable-management bracket M4 x 8-mm Phillips flathead screws 1 3 2 Rack-mount bracket Brackets Front-Mounted—Chassis Recessed in Rack Locate the rack-mount and cable-management brackets and screws (1, 2, 3 in the illustration above) and a Number 2 Phillips screwdriver. 1. Align the cable-management bracket (1) to the side of the router. Align the rack-mount bracket over it—as shown above—and insert and tighten the screws (3). Go to the “Two-Post or Four-Post Rack Installation” sect
Summary of the content on the page No. 9
5 3 1 5 3 1 2 1 4 3 1 Rack-mount bracket 3 Cable-management bracket 2 M4 x 8-mm Phillips flathead screws 4 M4 x 8-mm Phillips flathead screws Brackets Rear-Mounted—Front Protrudes from the Rack 1. Locate the threaded screw holes in the rear sides of the chassis. 2. Align a rack-mount bracket (1) to the threaded holes in the right side of the chassis. 3. Using a Number 2 Phillips screwdriver and two M4 x 8-mm Phillips flathead screws (2), attach the rack-mount bracket to the router. 4. Repeat S
Summary of the content on the page No. 10
5 3 1 5 3 1 Brackets Rear-Mounted—Front Recessed in the Rack 1. Locate the threaded screw holes in the rear sides of the chassis. 2. Align the first rack-mount bracket (1) to the threaded holes in the right side of the chassis. 3. Using a Number 2 Phillips screwdriver and two M4 x 8-mm Phillips flathead screws (2), attach the rack-mount bracket to the router. 4. Repeat Steps 2 and 3 for the bracket on the other side of the router. If you are not installing cable-management brackets, skip to th
Summary of the content on the page No. 11
NETWORK PROCESSING ENGINE-300 1 3 2 4 1 Chassis ground connector 3 Screws Grounding lug Wire 2 4 Chassis Ground Connection Installation Note The grounding lug and Phillips-head screws are not available from Cisco Systems. Get the grounding lug from an electrical-connector vendor and the screws from a hardware vendor. See Page 4 for the parts needed. 1. Locate the chassis ground connector (1) on the rear of your router chassis. 2. Insert the two screws (3) through the holes in the grounding lug
Summary of the content on the page No. 12
4 Connect the Router to the Network 2 1 3 4 1 Auxiliary port-DTE-mode; EIA/TIA-232, DTE-DB-25 3 Modem connector (for modem, CSU/DSU, etc.) Console port-DCE-mode; EIA/TIA-232, DCE-DB-25 Console terminal 2 4 connector (for data terminal) I/O Controller Console and Auxiliary Port Cable Connections Note Both the console and auxiliary ports are asynchronous serial ports; any devices connected to these ports must be capable of asynchronous transmission. 1. Before connecting a terminal to the consol
Summary of the content on the page No. 13
Product Number Description C7200-I/O-2FE/E 2 autosensing Ethernet/Fast Ethernet ports; equipped with 2 RJ-45 receptacles for 10/100-Mbps operation. Note This I/O controller works only with an NPE-225, board label 72-3453 rev. A0 or higher, or faceplate label 800-05418-03 rev. A0 or higher. To check for the correct NPE-225 version in software, use the show 7200 command and look under CPU EEPROM, for Hardware Revision 1.3 or higher. 1 C7200-I/O-FE 1 Fast Ethernet port; equipped with an MII re
Summary of the content on the page No. 14
5 Start and Configure the Router Power Cable Connections Warning This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit. Warning The AC power supply has double pole/neutral fusing. Connecting AC-Input Power 5 1 4 2 3 1 PWR OK LED 4 Cable-retention clip 2 Power switch 5 Hole for nylon cable 3 AC power cable 1. At the rear of the router, check that the power switch (2) is in the off (O) position. 2. Sl
Summary of the content on the page No. 15
4 1 3 2 1 Ground lead service loop 3 Cable tie 2 DC power leads 4 Power switch 1. At the rear of the router, check that the power switch is in the off (O) position. 2. Ensure that the –V and +V leads are disconnected from the power source. 3. Using a wire stripper, strip approximately 0.55 inch (14 mm) from the –V, +V, and ground leads (2). 4. Insert the stripped end of the ground lead (1) all the way into the ground lead receptacle on the DC-input power supply, and tighten the receptacle scre
Summary of the content on the page No. 16
Observing System Startup and Performing a Basic Configuration Check conditions prior to system startup: 1. Check that all hardware parts and cables are securely attached to the chassis. 2. Check that a Flash Disk or Flash memory card is installed. 3. Check that the console terminal is turned on. Starting and Configuring the Router 1. Place the power switch in the on (|) position. Repeat this action if there is a second power supply. 2. Listen for the fans; they should be operating as soon as pow
Summary of the content on the page No. 17
Performing a Basic Configuration Using the Setup Facility If you do not plan to use AutoInstall, do not connect the router’s serial (WAN) cable to the channel service unit/data service unit (CSU/DSU). If the WAN cable is not connected, the router boots from Flash memory and goes automatically into the setup facility. Note You can run the setup facility any time you are at the enable prompt (#) by entering the setup command. If the serial (WAN) cable is connected to the CSU/DSU and the router
Summary of the content on the page No. 18
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x0 Note The first two sections of the configuration script (the banner and the installed hardware) appear only at initial system startup. On subsequent uses of the setup command facility, the script begins with a System Configuration Dialog as shown in the following example: --- System Configuration Dialog --- At any point you may enter a question
Summary of the content on the page No. 19
8. For the following queries, enable routing on AppleTalk and IPX: Configure AppleTalk? [no]: yes Multizone networks? [no]: yes Configure IPX? [no]: yes 9. For the following queries, do not enable VINES, XNS, DECnet, or bridging: Configure Vines? [no]: Configure XNS? [no]: Configure DECnet? [no]: Configure bridging? [no]: 10. In most cases you will use IP routing. If you are using IP routing, you must also select an interior routing protocol. You can specify only one of two interior routing
Summary of the content on the page No. 20
Configuring Interfaces Following are the steps for configuring interfaces to allow communication over a LAN or WAN. To configure the interface parameters, you need your interface network addresses and subnet mask information. Consult with your network administrator for this information. Configuring Ethernet Interfaces In the following example, the system is being configured for an Ethernet LAN using IP. 1. Respond to the prompts as follows, using your own addresses and mask at the setup prompt
