Summary of the content on the page No. 1
Cisco 820 Series and SOHO Series Routers
Cabling and Setup Quick Start Guide
• Streamlined Installation: Try These Steps First!
Parts List
1: Connect the Router to a PC
2: Connect the Router to a Hub (Optional)
3: Connect a Digital Subscriber Line
4: Connect a Cisco 827-4V Router to a Phone or Fax
5: Connect the Power and Turn On the Router
6: Check the PC Configuration
7: Configure the Router with Cisco Router Web Setup
8: Congratulations! You’re Done!
Related Documentati
Summary of the content on the page No. 2
Streamlined Installation: Try These Steps First! Streamlined Installation: Try These Steps First! This router is configured for the most common type of installation. To set up the router quickly, try performing the following steps. If you cannot complete a step, or if you want more information at any point, skip to the “1: Connect the Router to a PC” section on page 3, and complete the steps described in the other sections of this Quick Start Guide. Step 1 Cable the router. Connect your PCs
Summary of the content on the page No. 3
Model Cisco 828 ETHERNET 10BASE T CONSOLE G.SHDSL TO HUB TO PC 4 3 2 1 Model Cisco 827-4V +5,+12,-12,-24,-71 VDC ETHERNET CONSOLE ADSL PHONE TO HUB TO PC 1 4 3 2 1 1: Connect the Router to a PC 1: Connect the Router to a PC Follow the steps shown in Figure 1 on page 3 to connect the router to a PC with an Ethernet network interface card (NIC) installed. Figure 1 shows portions of two router back panels. Refer to the back panel that is similar to the back panel of the router that you are inst
Summary of the content on the page No. 4
Model Cisco 828 ETHERNET 10BASE T CONSOLE G.SHDSL TO HUB TO PC 4 3 2 1 Model Cisco 827-4V +5,+12,-12,-24,-71 VDC ETHERNET CONSOLE ADSL PHONE TO HUB TO PC 1 4 3 2 1 1X 2X ETHERNET 3X 4X SPEED LED 1 2 3 4 100BaseTX SOLID 5 6 7 8 10BaseT BLINK 5X 6X 7X 8X MDI MDI-X 2: Connect the Router to a Hub (Optional) See the “3: Connect a Digital Subscriber Line” section on page 5 to complete the next step. 2: Connect the Router to a Hub (Optional) If you have PCs connected to a hub, follow the steps shown
Summary of the content on the page No. 5
Model Cisco 827 H ETHERNET 10BASE T CONSOLE ADSL TO HUB TO PC 4 3 2 1 Model Cisco 828 ETHERNET 10BASE T CONSOLE G.SHDSL TO HUB TO PC 4 3 2 1 3: Connect a Digital Subscriber Line Note You must use a crossover cable to connect a hub to an Ethernet port other than the ETHERNET 4 port on Cisco 827H, Cisco 828, SOHO 77H or SOHO 78 routers. Crossover cables must be purchased separately. 3: Connect a Digital Subscriber Line Follow the steps in Figure 3 to connect an asymmetric digital subscriber li
Summary of the content on the page No. 6
Model Cisco 827-4V +5,+12,-12,-24,-71 VDC ETHERNET CONSOLE ADSL PHONE TO HUB TO PC 1 4 3 2 1 4: Connect a Cisco 827-4V Router to a Phone or Fax 4: Connect a Cisco 827-4V Router to a Phone or Fax If you have a Cisco 827-4V router, you can connect analog telephones or fax machines to your router. Use the cables provided with these devices. The gray PHONE 1, 2, 3, and 4 ports are RJ-11 connectors. If you are outside North America, you must buy and attach adapters that allow telephones or faxes
Summary of the content on the page No. 7
Model Cisco 827-4V +5,+12,-12,-24,-71 VDC ETHERNET CONSOLE ADSL PHONE TO HUB TO PC 1 4 3 2 1 5: Connect the Power and Turn On the Router 5: Connect the Power and Turn On the Router Follow the steps in Figure 5 on page 7 to connect an AC adapter to the Cisco router and turn it on. (Figure 5 shows a Cisco 827-4V router, but the process applies to all Cisco 820-series and SOHO routers.) Caution Be sure to use the power supply that was supplied with your Cisco router. Power supplies for other Ci
Summary of the content on the page No. 8
6: Check the PC Configuration 6: Check the PC Configuration Each PC that is connected to the router must be configured to use the Transmission Control Protocol/Internet Protocol (TCP/IP) and to obtain its IP address automatically. Follow these steps to configure each PC that is running Microsoft Windows NT or Microsoft Windows 95 or 98. If the PC is running a different version of Microsoft Windows, refer to the documentation that came with the PC. Step 1 Start the PC, and open the Control P
Summary of the content on the page No. 9
8: Congratulations! You’re Done! 3. If the web page still does not appear, verify that the PC is configured to automatically receive an IP address. Follow the instructions in Step 4 in section “6: Check the PC Configuration.” If you need more information refer to the Cisco Router Web Setup Troubleshooting Guide, which is available on Cisco.com. 4. If the PC is configured to automatically receive an IP address, but the web page still does not appear, select Start/Run, type winipcfg in the R
Summary of the content on the page No. 10
Obtaining Documentation and Submitting a Service Request Cisco 828 Router and SOHO 78 Router Software Configuration Guide—Provides detailed configuration instructions for the Cisco 828 and SOHO 78 routers. Cisco Router Web Setup Troubleshooting Guide—Provides basic router configuration information. Configuration Note for the Cisco SOHO 77 Router—Provides software configuration information for the SOHO 77 and 77H routers. These documents are available on the World Wide Web. You can acce
