Summary of the content on the page No. 1
Guide to Supported Hardware for Cisco 7600
Series Routers with Cisco IOS Release 12.2SR
This publication lists the supported hardware for Cisco 7600 series routers with Cisco IOS Release
12.2SR.
Use this publication with the Release Notes for Cisco IOS Release 12.2SRA on the Cisco 7600 Series
Routers.
Contents
This publication contains these sections:
• Document Revision History, page 2
Supported Hardware, page 3
Unsupported Hardware, page 66
Related Documentation, page 68
Obtaining D
Summary of the content on the page No. 2
Document Revision History Document Revision History Revision Date Change Summary OL-10362-6 May, 2008 Added the following for Cisco IOS release 12.2(33)SRC1: SPA-4XT-Serial SPA support on SIP-200 Additional DWDM XFP support for ES20 line card, SIP-400, and SIP-600 OL-10362-5 April, 2008 Added the following for Cisco IOS release 12.2(33)SRB3: DWDM XFP support on Cisco 7600 ES20 line card and SIP-600 SFP-GE-T support on Cisco 7600 ES20 line card, SIP-400, and SIP-600 CWDM SFP support
Summary of the content on the page No. 3
Supported Hardware Revision Date Change Summary OL-10362-2 February, 2007 Added the following for Cisco IOS release 12.2SRB: RSP 720 Policy Feature Card 3C Policy Feature Card 3CXL Distributed Forwarding Card 3CXL SFP-GE-S, SFP-GE-L, SFP-GE-Z 1-Port and 24-Port Channelized CEoP SPAs Ethernet Services 20G line cards Application Control Engine (ACE) Module Service Application Module for IP 6000 W DC power supply Cisco 7609-S router chassis OL-10362-1 May, 2006 Initial version
Summary of the content on the page No. 4
Supported Hardware Enhanced FlexWAN Module Port Adapters, page 49 Service Modules, page 53 Fan Trays, page 58 Power Supplies, page 59 Chassis, page 60 Note Use the values in the “Power Required” column to determine the exact power requirements for your configuration to ensure that you are within the power budget. Daughtercard power is shown separately. Enter the show power command to display current system power usage. Supervisor Engines Supervisor Engine 720, page 4 Superv
Summary of the content on the page No. 5
Supported Hardware Supervisor Engine 720 Common Features Integrated 720-Gbps Switch Fabric 64-MB bootflash device 2 CompactFlash Type II slots (disk0 and disk1) Note Some Supervisor Engine 720 Release 12.2SR images are larger than the bootflash device and must be stored on a CompactFlash card. Two Ethernet uplink ports: – 1-MB packet buffer per port – Port 1—Gigabit Ethernet SFP – Port 2—Configurable as Gigabit Ethernet SFP or 10/100/1000 Mbps RJ-45 QoS port architecture (Rx/Tx): 1p1
Summary of the content on the page No. 6
Supported Hardware Supervisor Engine 720 with PFC3B Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-SUP720-3B 7.50 A@42 V Supervisor Engine 720 with PFC3B: 12.2(33)SRA 512-MB DRAM Policy Feature Card 3B (PFC3B); see the “RSP720-3C-10GE” section on page 10 Multilayer Switch Feature Card 3 (MSFC3): – 512-MB DRAM – 64-MB bootflash Note There are no memory-only upgrade options for WS-SUP720-3B. Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-
Summary of the content on the page No. 7
Supported Hardware These service modules: – WS-SVC-AON-1-K9—Application-Oriented Networking Module – WS-SVC-AGM-1-K9—Anomaly Guard Module – WS-SVC-ADM-1-K9—Traffic Anomaly Detector Module – WS-SVC-MWAM-1—Multi-Processor WAN Application Module Supervisor Engine 32 does not support these software features and commands: – Protocol independent multicast (PIM) snooping designated-router flooding configurability – NetFlow version 9 – Egress multicast replication – Multicast replication mode det
Summary of the content on the page No. 8
Supported Hardware QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t RSP720-3C-GE Product ID Power Minimum (append “=” for spares) Required Product Description Software Version RSP720-3C-GE 6.66 A@42 V Route Switch Processor 720 with PFC3C: 12.2(33)SRB Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45 Integrated 720-Gbps switch fabric PFC3C and MSFC4 with 512
Summary of the content on the page No. 9
Supported Hardware RSP720-3CXL-GE Product ID Power Minimum (append “=” for spares) Required Product Description Software Version RSP720-3CXL-GE 7.33 A@42 V Route Switch Processor 720 with PFC3CXL: 12.2(33)SRB Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45 Integrated 720-Gbps switch fabric PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash, 4-MB NVRAM
Summary of the content on the page No. 10
Supported Hardware RSP720-3C-10GE Product ID Power Minimum (append “=” for spares) Required Product Description Software Version RSP720-3C-10GE 7.33 A@42 V Route Switch Processor 720 with uplink ports: 12.2(33)SRC Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector Integrated 720-Gbps switch fabric PFC3
Summary of the content on the page No. 11
Supported Hardware RSP720-3CXL-10GE Product ID Power Minimum (append “=” for spares) Required Product Description Software Version RSP720-3CXL-10GE 7.33 A@42 V Route Switch Processor 720 with PFC3CXL: 12.2(33)SRC Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector Integrated 720-Gbps switch fabric PFC3C
Summary of the content on the page No. 12
Supported Hardware Policy Feature Cards Policy Feature Card Guidelines and Restrictions, page 12 Policy Feature Card 3BXL, page 13 Policy Feature Card 3B, page 13 Distributed and Centralized Forwarding Cards, page 14 Policy Feature Card Guidelines and Restrictions The PFC3 supports a theoretical maximum of 64,000 MAC addresses (32,000 MAC addresses recommended maximum). You cannot use one type of PFC3 (PFC3BXL or PFC3B) on one supervisor engine and a different type on the other su
Summary of the content on the page No. 13
Supported Hardware Policy Feature Card 3BXL Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6K-PFC3BXL 2.57 A@42 V Policy Feature Card 3BXL (PFC3BXL) Supported only with Supervisor Engine 720 12.2(33)SRA Note There are no memory upgrade options for WS-F6K-PFC3BXL. Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 or WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to thi
Summary of the content on the page No. 14
Supported Hardware Policy Feature Card 3CXL Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6K-PFC3CXL 2.57 A@42 V Policy Feature Card 3CXL (PFC3CXL) Supported only with RSP 720 12.2(33)SRB Note There are no memory upgrade options for WS-F6K-PFC3BXL. Distributed and Centralized Forwarding Cards Centralized Forwarding Card (WS-X6700-CFC), page 14 Distributed Forwarding Card 3BXL, page 15 Distributed Forwarding Card 3B, page 16 Distribu
Summary of the content on the page No. 15
Supported Hardware Distributed Forwarding Card 3BXL WS-F6700-DFC3BXL, page 15 WS-F6K-DFC3BXL, page 15 WS-F6700-DFC3BXL Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6700-DFC3BXL 3.30 A@42 V Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules Supported only with Supervisor Engine 720 12.2(33)SRA Note WS-F6700-DFC3BXL uses memory that is installed on the switching module. Refer to this publication for information about
Summary of the content on the page No. 16
Supported Hardware Distributed Forwarding Card 3B WS-F6700-DFC3B, page 16 WS-F6K-DFC3B, page 16 WS-F6700-DFC3B Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6700-DFC3B 3.00 A@42 V Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules Supported only with Supervisor Engine 720 12.2(33)SRA Note WS-F6700-DFC3B uses memory that is installed on the switching module. Refer to this publication for information about WS-F6700-DFC3B
Summary of the content on the page No. 17
Supported Hardware Distributed Forwarding Card 3CXL Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6700-DFC3CXL 2.35 A@42 V Distributed Forwarding Card 3CXL (DFC3CXL) for use on CEF720 modules Supported with Supervisor Engine 720 and Route 12.2(33)SRB Switch Processor 720 Distributed Forwarding Card 3C Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-F6700-DFC3C 1.65 A@42 V Distributed Forward
Summary of the content on the page No. 18
Supported Hardware 10-Gigabit Ethernet Switching Modules Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-X6704-10GE 6.28 A@42 V 4-port 10-Gigabit Ethernet XENPAK CEF720 with WS-X6700-CFC (adds 0.75 A@42 V) dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V) dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V) Supports egress multicast replication QoS port architecture (Rx/Tx): – With DFC3: 8q8t/1p7q8t – With CFC: 1q8t/1p7q8t Number of ports
Summary of the content on the page No. 19
Supported Hardware Product ID Power Minimum (append “=” for spares) Required Product Description Software Version WS-X6502-10GE 3.30 A@42 V 1-port 10-Gigabit Ethernet With Supervisor Engine 720: – dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V) – dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V) QoS port architecture (Rx/Tx): 1p1q8t/1p2q1t Number of ports: 1 Number of port groups: 1 Port ranges per port group: 1 port in 1 group With Supervisor Engine 720 12.2(33)SRA With Supervisor Engine 32
Summary of the content on the page No. 20
Supported Hardware Product ID Power Minimum (append “=” for spares) Required Product Description Software Version X2-10GB-LR 12.2(33)SRC Note To configure WS-X6708-10GE port oversubscription, refer to the hw-module oversubscription command in the command reference at this URL: http://www.cisco.com/en/US/products/ps6922/prod_command_reference_list.html Installation of a WS-X6708-10GE switching module in a chassis other than the following prevents operation at levels that are fully NEBS-com
