Summary of the content on the page No. 1
Quick Installation Guide
24-Port 10/100Mbps
Green Switch
Model# ASW324v2
Ver. 1A
Summary of the content on the page No. 2
Trademarks Copyright © 2011 Airlink101® Airlink101® is a registered trademark. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Phoebe Micro, Inc. Preface FCC Warning This device has been tested and found to comply with limits for Class A digital device, pursuant to Par
Summary of the content on the page No. 3
Introduction Congratulations on your purchase of the 24-Port 10/100Mbps Green Switch! It is an easy-to-install network switch which helps you to extend your network structure quickly and reliably. The 24-Port 10/100Mbps Green Switch is designed for energy saving, easy installation and high performance in an environment where network traffic and the number of users increase continuously. You can add other Ethernet devices like computers, IP cameras, and Network Attached Storage (NA
Summary of the content on the page No. 4
Section 1 Hardware Description 1.1 Hardware Interface • 24 x Port 10/100Mbps auto-negotiation RJ45 port • All ports support auto MDI/MDIX, no need to use cross-over cables 1.2 Panel 1.2.1 Front Panel The front panel of the Switch consists of LED indicators, and 24 10/100Mbps ports. The figure below shows the front panel of the Switch. Figure 1-1 Front Panel View of the Switch • 10/100Mbps Ports (Port 1~24): These ports support 10/100Mbps, and can operate in Half/Fu
Summary of the content on the page No. 5
1.2.2 Rear Panel Figure 1-2 Rear Panel View of the Switch • AC Power Connector: Supports AC 100~240V, 50~60Hz. NOTE: Do not cover or put anything on or surrounding the Switch while the Switch is operating. 1.2.3 LED indicators information The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed. Figure 1-3 Front Panel View of the Switch 4
Summary of the content on the page No. 6
• POWER: Power Indicator Status LED Color Solid Blinking Off The Switch is POWER Green N/A No power power-on • Port 1~24 10/100Mbps Status LEDs Status LED Color Solid Blinking Off No activities The port is LINK/ on the transmitting ACT Green 10/100Mbps or receiving No link Ethernet data at network 10/100Mbps Status LED Color Solid Blinking Off The The respective respective port is port is connected to 10/ 100M Green N/A connected the to the slow 10/100Mbp
Summary of the content on the page No. 7
Section 2 Installing the Switch The site where you place the Switch may greatly affect its performance. 2.1 Installation Please follow the guidelines below to install the Switch: • Please install the Switch in a fairly cool and dry place. Please refer to the Technical Specifications for the acceptable temperature and humidity operating ranges. • Please install the Switch on a sturdy, level surface that can support its weight. • When connecting the power cord to the Swit
Summary of the content on the page No. 8
2.3 Rack Installation The Switch is rack-mountable and can be installed on an EIA 11-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the Switch. 2.4 Power on the Switch The Switch has a universal power supply ranging from 100V to 240V AC, 50 ~ 60Hz power source. The AC power connector is located at the rear of
Summary of the content on the page No. 9
Section 3 Connecting the Switch This section describes how to connect the Switch to your 10/100Mbps Ethernet network. Your network device (i.e. computer, switch, IP Camera, VoIP) can be connected to any port of the Switch via a two-pair UTP Category 5 Cable. If the LED indicators do not light up after making a proper connection, check your network device, the cable, the Switch conditions and connections. 8
Summary of the content on the page No. 10
Section 4 Troubleshooting 1. Power LED is not on • Check if the power adapter is properly connected to the power outlet. Make sure the power jack is firmly plugged into the power socket of the switch. 2. Link/Activity is not lit when connect to 10/100Mbps device • Made sure that the network device attached to the switch is turned ON. • Check the network cable; make sure it is properly connected to the switch and the network device. • Check the network cable; ma
Summary of the content on the page No. 11
Section 5 Technical Specifications Standards • IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX, IEEE 802.3x Flow Control and IEEE 802.3az(EEE – Energy Efficient Ethernet) Network Cables • Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5, Twisted Pair (UTP). Up to 100m • Fast Ethernet (100Base-T): 2-pair UTP Cat. 5, Twisted Pair (UTP). Up to 100m Ports • 24 x 10/100Mbps Auto-Negotiation RJ45 Port Access Method • CSMA/CD Transmission Method • Store and Forward Data Transf
Summary of the content on the page No. 12
• 280mm x 165mm x 45mm (LxWxH) Weight • 1400g (3 lb) Physical and Environmental • Power Input: 100~240V AC, 50~60Hz • Operation Temperature: 0 °C ~ 40°C(32°F ~ 104°F) • Storage Temperature: -20°C ~ 70°C(-4°F ~ 158°F) • Humidity: 5% ~ 90% RH, non-condensing Certification • FCC, CE 11
Summary of the content on the page No. 13
Section 6 Technical Support E-mail: support@airlink101.com Toll-Free: 1-888-746-3238* Web Site: www.airlink101.com * Free Voice Technical Support is only available within the hardware warranty (1-Year Limited Warranty from the date of purchase). Customer is required to provide invoice as purchase evidence. **Network conditions and environmental factors as well as network overhead can lower actual data throughput rate. Copyright © 2011 AirLink101®
